-1PHONE: 763-331-3066 EMAL: info@hydro-smart.com WEB: www.hydro-smart.
-2PHONE: 763-331-3066 EMAL: info@hydro-smart .com WEB: www.hydro-smart.com WARNING!! Do not plug in control cord until all fluids are introduced and thermostat connection(s) are finished. DAMAGES - If unit is damaged, do not return to store. Please call 763-331-3066 for trouble shooting, returns, or replacement parts. Step 1- Mount Integrator Panel onto wall with four 1/4” x 1 - 1/2” Lg wood screws.
-3PHONE: 763-331-3066 EMAL: info@hydro-smart.com WEB: www.hydro-smart.com Filling The System Overview of a typical System What you’ll need: °1/2 HP Transfer Pump °5-10 Gal.
-4PHONE: 763-331-3066 EMAL: info@hydro-smart .com Filling The System WEB: www.hydro-smart.com E Quick Start B A Entry Fill A B Exit Fill C Purge Tee D 1/2 HP Transfer Pump E Air Eliminator F Hoses C F D When filling the system you will use a “Fill Entry Point” (A) and a “Fill Exit Point” (B), 5-10 gallon bucket, 3 washing machine hoses (F) (6 Ft), 1/2 Hp “Transfer Pump” (D) and system fluids. When filling, purge 1-loop at a time with the rest of the remaining loops closed.
-5PHONE: 763-331-3066 EMAL: info@hydro-smart.com WEB: www.hydro-smart.com Filling The System Entry Fill and Exit Fill You will fill your system using the entry and exit fill located on the panel. Entry fill will be used to pump water into the system. Exit fill is where the water will return back into your bucket.
-6PHONE: 763-331-3066 EMAL: info@hydro-smart .com WEB: www.hydro-smart.com Filling The System Purge Tee When filling your system, The purge tee handle should be in the vertical position, once the system is filled, purged, and pressurized, you will return it back to the horizontal position for normal operation.
-7PHONE: 763-331-3066 EMAL: info@hydro-smart.com WEB: www.hydro-smart.com Filling The System Transfer Pump and Hoses OUT Connect a hose from the “IN” side of the transfer pump and run it to your bucket. Connect a hose from the “out” side of the transer pump, and connect it to the “Entry Fill” on the panel. Connect a hose to the “exit fill” on the panel and run it back to your bucket.
-8PHONE: 763-331-3066 EMAL: info@hydro-smart .com WEB: www.hydro-smart.com Filling The System Air Eliminator When filling your system, close the air eliminator. Once your system is filled, purged, and pressurized, Open the air eliminator prior to operation by twisting the Air stem cap one turn counter clock wise.
-9PHONE: 763-331-3066 EMAL: info@hydro-smart.com WEB: www.hydro-smart.com Filling The System Manifold When filling the system, fill each loop individually. Close All loops By Twisting the knobs located on the manifold. Start with the first loop by opening it and purge all of the air out. When the air is purged out, close that loop and move on to the next loop, repeating this process until all loops have been purged.
-10PHONE: 763-331-3066 EMAL: info@hydro-smart .com WEB: www.hydro-smart.com Checking your system Verify System is running correctly Once your system has been Filled, Purged, and Pressurized, verify that both Primary and Secondary pumps are running. Check your supply and return pressures. Your supply gauge should be the same as what you pressurized it to. You should see about a 5-7 PSI differential on the return gauge when the system is running. Verify the boiler is energized and providing heat.