Installation Guide

ManualsBrandsHydro Systems ManualsBathAnn Arbor 6 ft. Center Drain Freestanding Air Bath Tub in Biscuit

INSTALLATION INSTRUCTIONS

USER MAINTENANCE INSTRUCTIONS

INSTALLATION INSTRUCTIONS

•

Read all instructions before proceeding with installation.

•

Inspect the tub before installation. If any damage or defects are found, do not install the tub. If the tub is not the right

size, model or color do not install the tub. Contact tech support at 661-775-0686 or email support@hydrosystem.com

•

INSTALLATION OF A THE MAESTRO COLLECTION BATHTUB MUST MEET ALL APPLICABLE CODES AND REGULATIONS.

IMPORTANT-

All tub and systems are thoroughly tested and inspected at the factory prior to shipment. However, it is possible for

damage to occur during shipment and installation. Such damage is not always readily visible. To maintain the warranty, it

is important to water test the tub, integral overﬂow and thermal system a minimum of 30 minutes for leaks prior to rough

installation before enclosing the tub. Hydro Systems is not responsible for the cost to remove/reinstall a tub.

CARE AND CLEANING-

To assure a long lasting “like new” look on your Maestro Collection bathtub we recommend the following easy

care procedures:

1) For normal maintenance, especially after use, clean with a soft cloth or sponge and a mild soap or liquid detergent.

2) DO NOT USE abrasives such as scouring compounds, scouring pads, steel wool or harsh chemicals on your

Hydro Systems bathtub. For deeper stains, hard scale deposits or any other cleaning or maintenance problem,

contact your Hydro Systems dealer.

THE MAESTRO COLLECTION

INSTRUCTIONS PERTAINING TO A RISK OF FIRE,

ELECTRIC SHOCK, OR INJURY TO PERSONS.

1. DANGER: To reduce the risk of injury, do not permit children to use this unit unless they are closely supervised at all times.

2. Use this unit only for its intended use as described in this manual. Do not use attachments not recommended by the

manufacturer.

3. Never drop or insert any object into any opening.

4. Do not operate this unit without the cover over the suction fitting.

5. The unit must be connected only to a dedicated electrical supply circuit that is protected by a Ground Fault Circuit

Interrupter (GFCI). The GFCI must be provided by the installer and should be tested on a routine basis by the homeowner.

To test the GFCI push the test button. The GFCI should interrupt power. Push the RESET button. Power should be restored.

If the GFCI fails to operate in this manner there is a ground current fault, indicating the possibility of an electric shock.

Do not use the tub. Disconnect the power and have the problem corrected by a qualified service representative. Re-test the

GFCI. Only when it is operating properly may the whirlpool tub be used.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: WHEN USING YOUR HYDRO SYSTEMS BASIC PRECAUTIONS SHOULD BE FOLLOWED, SEE BELOW

SAVE THESE INSTRUCTIONS FOR LATER REFERENCE

READ AND FOLLOW ALL INSTRUCTIONS

GLOSS FINISH

• Clean with mild dish soap and water, any non abrasive product to clean high-gloss counter surfaces will work.

• Remove dust with a soft damp cloth, for example; microﬁber or calico cloths.

• Clean oil, paint, ink or grease with rubbing alcohol and dry with a soft cloth.

• Avoid using abrasive cleaners, it is not safe to use these on your glossed product.

• Please do not use any sharp objects because that might result in scratching the surface of the tub.

Please do not use anything else other than what was instructed. Improper use can result in damage to the tub or

its ﬁnish and may void the warranty. Keep in mind, if you do end up damaging the tub, scratches can usually be

removed, buffed or polished out by an Authorized Hydro Systems Service Agent.

CLEANING INSTRUCTIONS

You will need to know the bathtub serial number attached

to your warranty card and also located on the bottom side

of the bathtub when contacting Hydro Systems.

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS. THE MAESTRO COLLECTION WARNING: WHEN USING YOUR HYDRO SYSTEMS BASIC PRECAUTIONS SHOULD BE FOLLOWED, SEE BELOW READ AND FOLLOW ALL INSTRUCTIONS 1. DANGER: To reduce the risk of injury, do not permit children to use this unit unless they are closely supervised at all times. 2. Use this unit only for its intended use as described in this manual.
PAGE 2
FREESTANDING INSTALLATION FIGURE 1 PREPARATION 1 Clean, level, and prepare the floor for installation. 2 Place the unit in the exact installed position on the floor and trace the outline of the bath with a pencil or any erasable marking (Figure 1). Templates for Freestanding bathtubs come with the tub. 3 Determine the location of the drain pipe, on the floor by taking measurements of the drain and waste location underneath the unit (Figure 2).
PAGE 3
FIGURE 6 FIGURE 9 INSTALL BATHTUB FIGURE 7 13 Adjust legs to a height of 1/8" max below skirt. 14 Apply generous bead of adhesive or silicone to the bottom of the tub supports and feet. (Figure 6). 15 Carefully set tub into position (Figure 7) and connect the drain hardware (previously installed). 16 Then apply a bead of tub and tile caulk or silicone around the edge of the base (Figure 8).
PAGE 4
FIXTURES • No Fixtures can be mounted on the tub deck. Floor and wall-mounted fixtures are required. • Wall-Mounted – The position of the tub and the reach of the spout are critical. Pay special attention to the spout reach when choosing your fixtures. Be careful to ensure the spout will extend out far enough to clear the tub deck and the falling water will not hit too high up the side wall of the tub and splash.