Installation Guide

ManualsBrandsHydro Systems ManualsBathHarrisburg 5.8 ft. Back Drain Freestanding Air Bath Tub in Biscuit

– 1 –

IMPORTANT SAFETY INSTRUCTIONS

GENERAL INSTRUCTIONS

MR. INSTALLER -

Please pass these

IMPORTANT

instructions along

to the homeowner!

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS.

TABLE OF CONTENTS

Follow All Instructions, Installation Instructions, General Requirements ...............................PAGE 2

General Requirements For Installation cont., Figure 1a, 1b, Figure 2a, 2b ..........................PAGE 3

Electrical Requirements, Installing The Tub ..........................................................................PAGE 4

Test The Whirlpool System, Setting The Tub ........................................................................PAGE 5

Operating Instructions, Figure 3 ............................................................................................PAGE 6

User Care And Maintenance .................................................................................................PAGE 7

Limited Warranty ...................................................................................................................PAGE 8

Summary of content (8 pages)

PAGE 1
RE L L A T S N I MR. ese h t s s a p e s Plea T IMPORTAN ng s alo n o i t c u r t s n i ner! w o e m o h to the IMPORTANT SAFETY INSTRUCTIONS GENERAL INSTRUCTIONS INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS. TABLE OF CONTENTS Follow All Instructions, Installation Instructions, General Requirements................................PAGE 2 General Requirements For Installation cont., Figure 1a, 1b, Figure 2a, 2b...........................
PAGE 2
WARNING: When using your Hydro Systems whirlpool tub, basic precautions should be followed. READ AND FOLLOW ALL INSTRUCTIONS. 1. DANGER: To reduce the risk of injury, do not permit children to use this unit unless they are closely supervised at all times. 2. Use this unit only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer. 3. Never drop or insert any object into any opening. 4. Do not operate this unit without suction cover installed. 5.
PAGE 3
The two most common types of installations are DROP-IN and THREE WALL installations. DROP-IN (Figure 1) For drop-in, or deck-mounted tubs, the finished height of the deck (X) where the tub will sit must equal the dimension from the trimmed edge of the tub to the floor at the drain end of the tub (A) plus 1”. The 1” is for the mortar bed. A 1" 1" X 1" Figure 1a Figure 1b Mortar NOTE: Tub lip resting on ledge, stringer or frame is non-weight bearing. Tub MUST be supported by mortor only.
PAGE 4
For installations that are any combination of decks, walls, and pony walls, use the same methods to determine critical heights. Remember that all supports must be at the same height and must establish a plane that is level front to back and side to side. 4. HOT WATER HEATER: As a rule of thumb, the capacity of the hot water heater needs to be at least 75% of the capacity of the whirlpool tub. ELECTRICAL REQUIREMENTS: A dedicated 20AMP GFCI Protected for each load item i.e. pump, blower, heater, ect.
PAGE 5
3. TEST THE WHIRLPOOL SYSTEM BEFORE YOU INSTALL THE TUB. All Hydro Systems whirlpool tubs are fully tested at the factory before shipping. However, it is the responsibility of the installer to check the system before installing the tub; if the tub is to be set in “rough framing” and can be accessed from all sides after setting, skip to paragraph 4 below. If the tub will be set in “finished framing” and can’t be accessed from all sides, we recommend testing the tub outdoors before setting it.
PAGE 6
ELECTRICAL CONNECTION: If the pump is in the standard location, it is plugged into the control box. So are all accessories. Check all connections. Make sure the bolts have been removed that hold the pump to the pump platform and plug the control box pigtail into the home’s dedicated GFCI. If the tub was ordered with the pump in a remote location, plug the pump into the control box. Plug all accessories into the control box. Check all connections and plug the control box into the home’s dedicated GFCI.
PAGE 7
ELECTRONIC SOFT TOUCH CONTROL - This is the on/off control switch for the whirlpool system. It bears the Hydro Systems logo. Press the logo once to turn the whirlpool system on. Press it again to turn the whirlpool system off. The whirlpool system is configured to run for thirty minutes and shut down automatically. If a longer bathing period is desired, press the logo to start it again. The whirlpool system will not turn on until the jets are covered with water.
PAGE 8
LIMITED WARRANTY This limited warranty is extended to the first user for a period of 10 years from date of purchase and is not enforceable by any other party. HYDRO SYSTEMS, at its option will repair or replace any defective or malfunctioning part of its system or bathtub, excluding pump, controller or accessories which may be guaranteed separately bt their manufacturer.