Installation Sheet

ManualsBrandsHydrosystems ManualsPlumbingLacey 66" Drop In Acrylic Air / Whirlpool Tub with Reversible Drain, Drain Assembly, and Overflow

IMPORTANT SAFETYINSTRUCTIONS

GENERAL INSTRUCTIONS

INSTALLER -

Please pass these

IMPORTANT

instruction along to

the homeowner!

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS.

TABLE OF CONTENTS

Follow All Instructions, Installation Instructions, General Requirements ...............................PAGE 2

General Requirements For Installation cont. .........................................................................PAGE 3

Electrical Requirements, Installing The Tub ..........................................................................PAGE 4

Test The Whirlpool System, Setting The Tub ........................................................................PAGE 5

Operating Instructions, Figure 3 ............................................................................................PAGE 6

User Care And Maintenance .................................................................................................PAGE 7

Limited Warranty ...................................................................................................................PAGE 8

DESIGNER COLLECTION

Please refer to www.hydrosystem.com for videos on how to install your bathtub and get specific dimensions on your

model bathtub

– 1 –

Summary of content (8 pages)

PAGE 1
R E L L A T S IN se e h t s s a p Please T IMPORTAN to ong l a n o i t c u r inst er! n w o e m o the h DESIGNER COLLECTION IMPORTANT SAFETYINSTRUCTIONS GENERAL INSTRUCTIONS INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS. TABLE OF CONTENTS Follow All Instructions, Installation Instructions, General Requirements................................PAGE 2 General Requirements For Installation cont...........................................................................
PAGE 2
WARNING: When using your Hydro Systems whirlpool tub, basic precautions should be followed. READ AND FOLLOW ALL INSTRUCTIONS. 1. DANGER: To reduce the risk of injury, do not permit children to use this unit unless they are closely supervised at all times. 2. Use this unit only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer. 3. Never drop or insert any object into any opening. 4. Do not operate this unit without suction cover installed. 5.
PAGE 3
Please refer to www.hydrosystem.com for videos on how to install your bathtub and get specific dimensions on your model bathtub GENERAL REQUIREMENTS FOR INSTALLATION MECHANICAL REQUIREMENTS: 1. WEIGHT: Tubs must be installed in a location that will support the combined weight of the tub plus the water plus the bather. As a rule of thumb, this will be a maximum of 1000 lbs. for a 60" tub, 1200 lbs. for a 66" tub, and 1400 lbs. for a 72" tub. 2.
PAGE 4
Figure 2a X Figure 2b A X B 1" For installations that are any combination of decks, walls, and pony walls, use the same methods to determine critical heights. Remember that all supports must be at the same height and must establish a plane that is level front to back and side to side. 4. HOT WATER HEATER: As a rule of thumb, the capacity of the hot water heater needs to be at least 75% of the capacity of the whirlpool tub.
PAGE 5
TEST THE ENTIRE SYSTEM INCLUDING INTEGRAL OR LINEAR OVERFLOWS BEFORE YOU INSTALL THE TUB All Hydro Systems whirlpool tubs are fully tested at the factory before shipping. However, it is the responsibility of the installer to check the system before installing the tub; if the tub is to be set in “rough framing” and can be accessed from all sides after setting, skip to paragraph 4 below.
PAGE 6
ELECTRICAL CONNECTION: If the pump and/or is in the standard location, it is plugged into the control box. So are all accessories. Check all connections. Make sure the bolts have been removed that hold the pump to the pump platform and plug the control box pigtail into the home’s dedicated GFCI. If the tub was ordered with the pump in a remote location, plug the pump into the control box. Plug all accessories into the control box.
PAGE 7
ELECTRONIC SOFT TOUCH CONTROL - This is the on/off control switch for the whirlpool system. It bears the Hydro Systems logo. Press the logo once to turn the whirlpool system on. Press it again to turn the whirlpool system off. The whirlpool system is configured to run for thirty minutes and shut down automatically. If a longer bathing period is desired, press the logo to start it again. The whirlpool system will not turn on until the jets are covered with water, if you have optional water level protection.
PAGE 8
Hydro Systems, Inc. warrants to the original purchaser of the Combination, Whirlpool, Thermal Air or Soaking Tub that the plumbing fittings and equipment will not leak water due to defects in materials or workmanship for a period of 3 years from the purchase date. Limited labor for any repair is covered for a period of 3 years for the labor aspect of the warranty only. This limited warranty does not include any other items not manufactured by HYDRO SYSTEMS, INC. HYDRO SYSTEMS, INC.