5600 Meter Initiated Valve Water Softener Operation Manual WQA Tested and Certified against CSA B483.1 Read all instructions carefully before operation.
WQA Tested and Certified against CSA B483.1 Performance Data Sheet and Specification Item Number Model Number Capacity - Grains @ 15lbs/ Factory set @ 6lbs/ cu.ft. @ 10 lbs/cu.ft. cu.ft. Service Maximum Resin Flow Rate Flow to Drain Tank Size USGPM (LPM) USGPM (LPM) inches (mm) Twin Tank Models 7600 5600MI-20 22,000 20,000 15,000 8 (30.3) 1.2 (4.5) 7710 5600MI-20 (8x44) 22,000 20,000 15,000 8 (30.3) 1.2 (4.5) 7601 5600MI-30 30,000 27,000 20,000 10 (37.9) 1.5 (5.
Installation Instructions CAUTION: If the ground from the electrical panel or breaker box to the water meter or underground copper pipe is tied to the copper water lines and these lines are cut during installation of the Noryl bypass valve and/or poly pipe, an approved grounding strap must be used between the two lines that have been cut in order to maintain continuity.
2. Water to supply outside faucets used to water lawns and gardens should not be softened. A new water line is often required to be connected to supply hard water to the inlet of the water softener and to the outside faucets. Cut the water line between where it enters the house; before any lines that branch off to feed the hot water heater or other fixtures in the house; and as near the desired location of the water softener as possible.
Drain Line Connection NOTE: W aste connections or drain outlet shall be designed and constructed to provide for connection to the sanitary waste system through an air-gap of 2 pipe diameters or 1 inch (22 mm) whichever is larger. WARNING: N ever insert drain line directly into a drain, sewer line, or trap. Always allow an air gap between the drain line and the wastewater to prevent the possibility of sewage being back-siphoned into the conditioner.
Operating Instructions Setting the Time of Day (Figure 3) This is a 24-hour timer and must correspond with the correct time on your wrist watch to ensure proper cycling of your conditioner. Disengage the drive gear by pressing and holding in the RED BUTTON on the left side of the control. Now turn the large 24-hour gear until the actual time of day is at the time of day arrow at the bottom of the panel. Release the red button to re-engage the drive gear.
Salt Settings are factory set and should not need adjustment 5600MI-20................................ 8 lbs WTC5620................................. 7 lbs 5600MI-30.............................. 10 lbs WTC5630............................... 10 lbs 5600MI-45.............................. 15 lbs 5600MI-60.............................. 10 lbs 5600MI-90.............................. 15 lbs Automatic Bypass The regeneration cycle lasts approximately 2-1/2 hours, after which soft water service will be restored.
Checking the Salt Level Maintenance Check the salt level monthly. Remove the lid from the cabinet or brine tank, make sure salt level is always above the brine level (you should not be able to see water). Adding Salt Use only clean salt labeled for water conditioner use, such as crystal, pellet, nugget, button or solar. The use of rock salt is discouraged because it contains insoluble silt and sand which build up in the brine tank and can cause problems with the system’s operation.
Parts Breakdown Front View Outlet Back View Top View BRINE TANK Inlet Side View 9 8 10 2 BRINE TANK 1 4 6 3 7 Resin 5 Part Number Model Description Distributor (1) Valve (2) Tank (3) Brine Tank (4) Grid (5) Safety Float (7) Resin #21501 7600 5600MI-20 19478 56010-20 100011-2 100284 N/A 13624 0.75 CF 7710 5600MI-20 (8 x 44) 19478 56010-20 18444 100284 N/A 13624 0.75 CF 7601 5600MI-30 19478 56010-21 19480 100284 N/A 13624 1.
Trouble Shooting Guide Before calling for service, follow the steps below, then MANUALLY REGENERATE your softener. PROBLEM 1. S oftener delivers hard water CAUSE A. B. CORRECTION Bypass valve is open No salt in brine tank C. Insufficient water flowing into brine tank D. Salt bridged E. Loose brine line 2. Intermittent soft water F. Plugged injector assembly A. Control will not draw brine properly B. Using hot water during regeneration cycle C. Incorrect salt setting D.
GUARANTEE HYDROTECH guarantees that your new water conditioner is built of quality material and workmanship. When properly installed and maintained, it will give years of trouble-free service. FIVE YEAR COMPLETE PARTS GUARANTEE HYDROTECH will replace any part which fails within 60 months from date of manufacture, provided the failure is due to a defect in material or workmanship.
