5600SXT Valve nextSand Turbidity & Sediment Filter Operation Manual Read all instructions carefully before operation.
Performance and Specifications Item # Flow Rates USGPM (For ultrafine particle removal) Model # Service Peak Backwash Service Flow rates for Typical Application USGPM Peak Backwash Installation Space Fiberglass Tank Size Inches Shipping Weight Lbs 7680 5600SXTM-847NEXTSF-75 4.0 5.0 5 5.6 7.0 5 10 x 10 x 57 8 X 47 75 7681 5600SXTM-948NEXTSF-100 5.0 7.0 6 7.1 8.8 6 11 x 11 x 58 9 X 48 115 7682 5600SXTM-1054NEXTSF-150 7.0 8.0 7 8.7 10.
Control Operation During Programming The control will only enter the Program Mode with the valve in Service. While in the Program Mode, the control will continue to operate normally, monitoring water usage and keeping all displays up to date. Control programming is stored in memory permanently, eliminating the need for battery back-up power. Meter Immediate Control A meter immediate control measures water usage and regenerates the system as soon as the calculated system capacity is depleted.
Installation Instructions All government codes and regulations governing the installation of these devices must be observed. CAUTION: If the ground from the electrical panel or breaker box to the water meter or underground copper pipe is tied to the copper water lines and these lines are cut during installation of the Noryl bypass valve and/or poly pipe, an approved grounding strap must be used between the two lines that have been cut in order to maintain continuity.
2. Attach the bypass valve to the control valve. Connect the inlet and outlet of the water filter to the plumbing in the house. The control valve must not be submitted to temperatures above 71°C (110°F). When sweat fittings are used, to avoid damaging the control valve, solder the threaded copper adapters to the copper pipe and then, using Teflon tape, screw the assembly onto the bypass valve. CAUTION: Do not use pipe thread compound as it may attack the material in the valve body. 3.
Operating Instructions Figure 3 The valve has been pre-programmed with factory settings as follows: Capacity between Regenerations............ 1,500 gallons Regeneration Cycle Step Programming 1. Backwash . ............................................ 6 2. Brine Rinse............................................. 0 3. Rapid Rinse .......................................... 5 4. Brine Refill . ...........................................
User Programming Mode Options Abbreviation Parameter Description DO Day Override The timer’s day override setting This is an option only. Please do not adjust before consulting an authorized dealer. RT Regeneration Time The time of day that the system will regenerate (meter delayed, timeclock, and day-of-week systems) RC Reserve Capacity CD Current Day The fixed reserve capacity The current day of week NOTES: Some items may not be shown depending on timer configuration.
Set treated water capacity (only available in metered systems) 1. Set time of day to 12:01 PM. 2. 3. 4. 5. Press Extra Cycle button to exit the time of day display. Press and hold the Up and Down buttons together until the programming icon replaces the service icon. Press Extra Cycle button till “C” is displayed in the upper left corner of the screen. Use Up and Down buttons to set the amount of treated water that can flow through the unit before a regeneration is required. 650 gallon capacity 6.
Start-Up Instructions Water-only backwash 1. Check that the correct backwash (BW) flowrate has been determined based on the water temperature. (See table below) 2. Allow the tank to slowly fill with water from the bottom. This is most easily accomplished by setting the control valve to the backwash position and partially opening the inlet valve until water flows from the drain line. 3. Allow the media to soak for at least 30 minutes. 4.
Maintenance Instructions Maintenance of your new water filter requires very little time or effort but it is essential. Regular maintenance will ensure many years of efficient and trouble free operation. Care of all Water Filters To retain the attractive appearance of your new water filter, clean occasionally with a mild soap solution. DO NOT use abrasive cleaners, ammonia or solvents. Never subject your filter to freezing.
GUARANTEE HYDROTECH guarantees that your new water conditioner is built of quality material and workmanship. When properly installed and maintained, it will give years of trouble-free service. FIVE YEAR COMPLETE PARTS GUARANTEE HYDROTECH will replace any part which fails within 60 months from date of manufacture, provided the failure is due to a defect in material or workmanship.
