Installation Guide
LIVE OUTDOOR REALITY (LOR)
TM
EXPERIENCE
Upright Storage Kit Installation Guide
Upright Storage Kit Installation Guide
Drywall: Wood Studs
Gather the tools you will need:
Drill
Stud fi nder
Level
Wrench
Pencil
Measuring tape
NEED HELP?
support@hydrow.com
hydrow.com
PREP
STEP 1
Safety
1
STEP 2
Lay out the parts
2
STEP 5
Drill holes
5
STEP 6
Secure the plate
6
STEP 7
Add the plastic cover
7
STEP 8
A ach the strap
8
For your safety, we recommend professional
installation of the Hydrow Upright Storage Kit.
Please contact your local construction company
or handyman to schedule installation.
If you choose to install the Hydrow Upright
Storage Kit yourself, please follow all instructions
in this guide carefully, and only mount the kit to
studs on load-bearing walls.
Use these instructions exactly as written. If
you do not install the Hydrow Upright Storage
Kit according to these exact instructions, your
warranty of the Hydrow Upright Storage Kit will be
voided, and you will assume all liability for product
use. To view the warranty, visit
www.hydrow.com/warranty. Any changes or
modifi cations not expressly approved by Hydrow,
Inc. would void your authorization to operate this
device.
Use these instructions exactly as written. If you
do not install the Hydrow Upright Storage Kit
according to these exact instructions, you may:
1) Cause personal injury to yourself or nearby
bystanders in the process of storing your Hydrow
or removing it from storage
2) Cause damage to the rower by improperly
storing or retrieving it
3) Cause personal injury to yourself if you then
proceed to use a rower that has been damaged
through improper use of the Upright Storage Kit
a. Use a drill and included 15/64” drill bit to
make 3” deep holes in the two circles on the
template. Ensure drill is held steady while
drilling.
b. If an error renders a hole unusable, drill a
comparable hole in the same area.
a. Place the plate on the wall as
shown.
b. Place washers over lag bolts.
c. Place one lag bolts with washer into each of the
drilled holes.
d. Screw the lag bolts halfway with the wrench.
e. Use the level to ensure the plate is straight.
f. Tighten all lag bolts completely.
a. Fit the plastic cover over the plate as shown.
b. The cover will snap into place using the
embedded magnets when secure.
a. Unfold strap and locate the metal clip.
b. Open clip and secure it to the storage bracket.
A 1x Strap
B 1x Bracket
C 1x Cover
This guide will teach you how to safely and securely
install your Upright Storage Kit for Hydrow. Please
follow all instructions in this guide for the safety of
the rower, your personal property, and the people in
your home.
D 2x 3/8” x 3” Wood
Stud Lag Bolts
E 2x Washers
F 1x 15/64” Drill Bit
G 2x Wheel Stickers
CARE
STEP 11
Continued Safety Checks
INSTALLATION
STEP 3
Choose a spot
3
STEP 9
Mark the wheel spots
9
11
USE
STEP 10
Hydrow storage with the
Upright Storage Kit
10
STEP 4
Determine location
4
a. Select a location for the Upright Storage Kit with
at least 2 feet of clearance on all sides.
b. Using a stud fi nder, choose a stud for the Upright
Storage Kit.
c. Mark the left and right side of the stud in
pencil.
d. Mark the center of the stud in pencil.
NOTE: If you cannot locate a stud, please
contact a local construction company to locate
the stud.
Decide on the perpendicular or parallel storage
position.
a. For perpendicular storage:
Find the point on the wall where the line created
by connecting the two drill holes meets the fl oor.
Mark a spot 9” to the right and 9” to the left of
that point.
Extend each mark 38” onto fl oor (perpendicular to
wall) and place stickers.
a. Regularly inspect the hardware and tighten the
bolts.
b. To contact Customer Care, please visit
support.hydrow.com
or email support@hydrow.com.
a. Find a friend to help. This is a two person job.
b. Unplug Hydrow.
c. Collapse the Hydrow monitor into its storage
position by simultaneously lifting the monitor’s
weight and pressing the fold button on Hydrow’s
neck. Once the button is depressed, gently guide
the monitor into its collapsed storage position.
d. Slide seat toward front of top rail.
e. Being mindful of cord position, lift Hydrow from
the back legs and tip Hydrow onto its wheels,
positioning the wheels onto the wheel stickers
marking Hydrow’s storage spot.
f. Once in place, lift Hydrow into its full vertical
storage position, bracing Hydrow with one hand
while taking hold of the storage kit strap in the
other hand.
g. Wrap the strap around Hydrow’s rail below the
back legs and clip to secure.
a. Put a mark between 64” and 70” above the fl oor
(depending on strap height preference).
b. Put a second mark 4 3/4” above the fi rst mark.
Note: The Hydrow Upright Storage Kit is not
compatible with drywall with metal studs.
b. For parallel storage:
Find the point on the wall where the line created
by connecting the two drill holes meets the fl oor.
Mark a spot 12” to the left or right of that point
(depending on which way you want your Hydrow
to face in the stored position).
Mark a line perpendicular to the wall at that
point.
Place stickers 4” and 22” away from the wall
along the line.
A B C D E F G