Parts List

ManualsBrandsHytera Communications ManualsComputers & AccessoriesDIGITAL REPEATER

Table Of Contents

1. Product Overview

1.1 Front Panel

No. Part Name No. Part Name

Air Inlet for PA 8 Timeslot A RX Indicator

Channel Up Key 9 Timeslot A TX Indicator

Channel Down Key 10 Analog Mode Indicator

Seven-segment Display 11 Digital Mode Indicator

Alarm Indicator 12 Audio/Programming Connector

Timeslot B RX Indicator 13 Air Inlet for Power Supply

Timeslot B TX Indicator / /

1.2 Rear Panel

1.2.1 General Version

No. Part Name No. Part Name

TX Antenna Connector 6 DC Power Inlet

Monitor/Tuning Interface 7 AC Power Inlet

Accessory Connector 8 AC Power Switch

RX Antenna Connector 9 Ground Screw

5 LAN

Interface / /

Summary of content (10 pages)

PAGE 1
. Product Overview 1.1 Front Panel No. Part Name No. Part Name 1 Air Inlet for PA 8 Timeslot A RX Indicator 2 Channel Up Key 9 Timeslot A TX Indicator 3 Channel Down Key 10 Analog Mode Indicator 4 Seven-segment Display 11 Digital Mode Indicator 5 Alarm Indicator 12 Audio/Programming Connector 6 Timeslot B RX Indicator 13 Air Inlet for Power Supply 7 Timeslot B TX Indicator / / 1.2 Rear Panel 1.2.1 General Version No. Part Name No.
PAGE 2
1.2.2 Enhanced Version No. Part Name No. Part Name 1 TX Antenna Connector 7 USB Connector 2 Monitor/Tuning Interface 8 DC Power Inlet 3 Accessory connector 9 AC Power Inlet 4 RX Antenna Connector 10 AC Power Switch 5 LAN Interface 11 Ground Screw 6 WAN Interface / / 1.3 Internal Parts 1.3.
PAGE 3
No. Part Name No. Part Name 1 PA Module 5 Wind Scooper 2 Baseband Module 6 Fan 3 Network Board 7 Control Panel 4 Power Supply Module 8 Floating Charge Board 1.3.2 Enhanced Version No. Part Name No.
PAGE 4
2. Installation To ensure optimum performance and reliability of the repeater, read the following instructions carefully. 2.1 Installation Requirements Installation Environment The repeater must be installed in a dry and well-ventilated place. The ambient temperature ranges from –30°C to +60°C, and the relative humidity is 95%. Installation Location The repeater can be installed in a rack, bracket, and cabinet, or on a desk. For more information, refer to the Safety Information Booklet. 2.
PAGE 5
1. Wear the anti-static gloves. 2. Place the repeater to a proper location. 3. Connect accessories including the antenna, feed lines, and power cords to the repeater. You must purchase the antenna and feed lines separately. 4. Ground the repeater through the ground screw located on the rear panel. 2.4 Post-installation Check To check whether the repeater works properly, do as follows: 1. Turn the repeater on. 2. Observe the LED indicators and the display in the front panel. For details, refer to 3.
PAGE 6
3. Basic Operations 3.1 Turning the Repeater On or Off  If the repeater is connected to a DC power supply, press the power switch on the DC power supply to turn the repeater on or off.  If the repeater is connected to an AC power supply, press the AC Power Switch located in the rear panel to turn the repeater on or off. 3.2 Switching the Channel You can use the Channel Up or Channel Down key in the front panel to switch the channel.
PAGE 7
Indicator Description Repeater Status timeslot B. Digital mode: The repeater is receiving in timeslot Green Timeslot B RX B. 3.3.2 Network Interface Indicator Description LED 1 Flashing Repeater Status The network card is transmitting data. The data transmission rate is 1000 LAN interface/WAN interface Glowing M/100 M. LED 2 Off The Data transmission rate is 10 M.
PAGE 8
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications.
PAGE 9
FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an occupational/controlled environment. This transmitter must not be co‐located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 200cm between the radiator &you body. ISEDC Statement This device complies with Innovation, Science and Economic Development Canada Compliance license-exempt RSS standard(s).
PAGE 10
RF Exposure Compliance and Control Guidelines and Operating Instructions To control your exposure and ensure compliance with the occupational/controlled environmental exposure limits, always adhere to the following procedures. Guidelines: Do not remove the RF Exposure Label from the device. User awareness instructions should accompany device when transferred to other users. Do not use this device if the operational requirementsdescribed herein are not met.