Preface Thanks for your favor in our product. To derive optimum performance from the product, please read this manual, the corresponding TETRA Terminal Series Feature Book and the Safety Information Booklet carefully before use.
Term Individual Call Group Call Half-duplex Full-duplex Direct Mode Operation (DMO) 13 A half-duplex or full-duplex call initiated by an individual user to another individual user. A half-duplex call initiated by an individual user to a group. Half-duplex communication is also called “two-way alternate communication”. It indicates the communication is provided in both directions, but only one direction at a time, that is, only one party is allowed to transmit or receive at a time.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Contents Contents---------------------------------------------------------------------1 Managing the Contacts -------------------------------------------6 Items in the Package-----------------------------------------------------2 Using BT Device ----------------------------------------------------7 Product Overview ---------------------------------------------------------2 Enabling/Disabling Covert Mode -------------------------------7 Product Controls--------------------------------------------------
Items in the Package Product Overview Please unpack carefully and check that all items listed below are received. If any item is missing or damaged, please contact your dealer.
The charger LED indicates you the charging process. When the charger LED glows red, the charging begins. When charging is complete, the charger LED glows green. The table below shows you the details. Step 2 Loosen the screws fixing the SIM card cover, open the cover, and then place the card into the slot properly, as shown in the figure below. Note ●● To achieve optimal battery performance, please charge the battery for 5 hours before initial use.
Status Indication Name Status Icon Name Battery Strength Icon RSSI Icon Message Icon Operation Mode Icon Profile Icons Accessory Icon Icon Terminal Status The battery strength is low. More bars indicate more battery strength. GPS Icon The terminal has not registered with the network (applicable for TMO only). More bars indicate a stronger signal. The Inbox is full. Normal Terminal Status A GPS module is connected and the valid GPS data is received.
Menu Navigation TMO Menu The following menu lists show the full menus of the terminal in TMO and DMO. You can select your needed menus to be displayed via your dealer. To select and confirm the options in the menu, operate as follows: in the home screen, you can press the Func/OK key to enter the “Func” menu, or press the Options/Back key to enter the “Options” menu; then press the Up/Down key on the Navigation key to select the needed menu, finally press the Func/OK key.
Basic Operations Turning On/Off To turn on the terminal, rotate the Power On-Off/ Volume Control knob clockwise. Then the LED indicator flashes green, and the terminal shows the power-up screen and sounds power-up alert. Upon successful powering on, the terminal enters the home screen. In TMO, after being turned on; the terminal will register with the network. In DMO, the terminal will be ready for use after being turned on.
Func menu by pressing the Func/OK key, and go to “PhoneBook” menu; then press Func/OK to enter “Memory”. Using BT Device As soon as the product gets successful connection to the BT device, the audio signal will be transmitted via the BT device instead of the microphone and speaker of the product. Caution: ●● To derive the optimum audio quality, you should use BT devices specified by The Company: wireless headset, wireless remote speaker microphone and wireless finger PTT.
Call Services TMO Answering an Individual Call ● Individual Call In TMO mode, an individual call can be initiated either as a half-duplex call or full-duplex call, which can be received without pressing any key (Direct Signaling) or PTT (Hook Signaling). Contact or by pressing your dealer for such programming as well as more details. Initiating an Individual Call ● ● Via Menu In the home screen, press Func/OK key to enter the “PhoneBook” or “Call Log” submenu, and select a contact.
Telephone Call The telephone call is a full-duplex individual call with Hook signaling. To initiate the call, follow the steps below. To answer or hang up/reject the call; see the “Individual Call” in “TMO”. Initiating a Telephone Call Step 1 Select a gateway. On the home screen, press Options/Back key to enter the “PSTN G AT E” o r “PA B X G AT E” s u b m e n u . Select an appropriate gateway, and press Func/OK key to confirm. Step 2 Input a telephone number. Return to the h o m e s c r e e n .
Note: The Send StatusMsg function and the status message are predefined by the dealer via the CPS. Sending a Status Message ● ● Press the Func/OK key and go to “Message -> Create Msg -> StatusMsg -> Sel Msg”. Select a desired status message, and press the Func/OK key to proceed. Choose either an individual or a group as the target contact, input the appropriate number and press Func/OK to send the message. Long press the programmed Send StatusMsg key to send the preset status message directly.
Troubleshooting Phenomenon Network registration fails or network can not be found. Analysis Solution The terminal may be operating in DMO. The terminal may get out of the network coverage (in TMO mode). Switch to TMO mode. Check the signal strength. Make sure the terminal is within the network coverage. Contact the network operator for the terminal authorization. Check the signal strength. Make sure the terminal is within the network coverage. The terminal may not be granted network access.
Phenomenon Analysis Solution As for the same status message, the content displayed at the receiving party is different from that of the sending party . The parties have associated the same status message ID with different contents. Make sure the status message ID is associated with the same content. The BT device can not connect to the product. The BT device battery may be low. Charge the BT device. The distance between the BT device and the product may be out of 10 meters.
Care and Cleaning Optional Accessories To guarantee optimal performance as well as a long service life of the product, please follow the tips below. The following items are the main optional accessories for the product, and please consult your local dealer for more other accessories. Caution: Use the accessories specified by the Company only. If not, we shall not be liable for any losses or damages arising out of use of unauthorized accessories.
Appendix SSI&TSI Dialing Rules In the TETRA system, subscribers are distinguished by different identities. Each subscriber is assigned with a unique short subscriber identity (SSI), which serves a part of the TETRA subscriber identity (TSI). And TSI is generally composed in this way: Mobile Country Code (MCC) + Mobile Network Code (MNC) + SSI. To initiate an individual call, please dial the SSI or TSI in compliance with the rules below. ● SSI Dialing Make sure there are not more than 8 digits.
