26” TFT LCD TV OWNER’S MANUAL HLT-2672
English OWNER’S MANUAL Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back of the set and quote this information to your dealer when you require service.
Table of Contents Important Safety instructions 3 First step Safety instructions 5 LCD TV Overview Front and side view Connection Panel Overview Remote Control Key Functions Using the remote control Accessories 11 11 12 13 14 Equipment Connections and Setup VCR Setup Cable Box Setup DTV Setup DVD Setup PC Setup DVI Setup 15 16 17 18 18 19 Basic Features Setup and Operation Turning on the TV Checking features 21 21 Sleep Timer Setting Sleep Timer 22 Picture & Sound Adjusting picture control Adjus
OWNER’S MANUAL Important Safety Instruction 1) 2) 3) 4) 5) 6) 7) 8) Read all of these instructions. Save these instructions for later use. Follow all warnings and instructions marked on the product. Follow all instructions. Do not use the TV near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturerís instructions. Do not install near any heat sources such as radiators.
OWNER’S MANUAL Important Safety Instruction FCC INFORMATION (U.S.A.) Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
OWNER’S MANUAL Safety Instructions Indoor Installation WARNING Do not place the TV in direct sunlight or near heat sources such as radiators, fires and stove etc. NOTES Do not place inflammable materials beside the TV • This may cause a fire hazard ! • This may cause a fire hazard ! NOTES When unpacking or moving the TV two people will be necessary to lift it safely. Do not place the TV where it might be exposed to dust. • This may cause a fire hazard ! NOTES Ensure good ventilation around the TV.
Safety Instructions Outdoor Installation WARNING Do not use the TV in a damp place such as a bathroom where it is likely to get wet. • This may cause a fire or an electric shock hazard ! WARNING In case of using a receiver (VCR, Digital Set Top Box), do not place an antenna in the vicinity of power lines. • This may cause an electric shock. In case of using a receiver (VCR, Digital Set Top Box), contact your service center to construct an antenna because it needs skilled man.
OWNER’S MANUAL Safety Instructions Power NOTES Do not place heavy objects on the power cord • This may cause a fire or an electric shock hazard ! Do not use too many plugs on the main multioutlet. Never touch the power plug with a wet hand • It may result in overheating of the outlet and causes a fire hazard ! • This may cause an electric shock hazard ! NOTES Hold the plug firmly when unplugging. If you pull the cord the cord may be damaged. Prevent dust collecting on the power plug pins or outlet.
OWNER’S MANUAL Safety Instructions Using NOTES In case of impact shock or damage to the monitor switch it off and unplug it from the outlet and contact your service center. Do not allow any objects to fall into the TV. • This may cause an electric shock hazard ! • This may cause a fire or an electric shock hazard ! NOTES Do not drop the TV or allow impact shock.
OWNER’S MANUAL Safety Instructions Others WARNING Do not watch the TV while driving or walking. • This may cause an accident. NOTES Do not place heavy objects on the TV. • This may cause serious injury to a child or adult. NOTES The distance between eyes and the screen should be about 1.5m. • If not, eyes will strain. Unplug the TV from the wall outlet when it is left unattended and unused for long periods of time.
OWNER’S MANUAL *FRONT AND SIDE VIEW 1. POWER button : Switches TV set on or off. 2. MENU button : Displays a menu. 3. SELECT button : Selects the A/V source. 4. VOLUME (▲ / ▼) : Adjusts the volume / Adjusts menu settings. 5. PR (▲ / ▼) : Selects a programme or menu item. *Connection Panel Overview Back Panel 1. DVI IN : Digital Video Interface. 2. RGB-DTV / PC INPUT : PC OR DTV Video Source Input. 3. PC AUDIO IN : Connect the audio cable from the PC to the PC AUDIO IN of the set. 4. L.
OWNER’S MANUAL Remote Control Key Functions - When using the remote control aim it at the remote control sensor on the TV 1. POWER Turns on TV or off from st/by mode. 2. MUTE Turns the sound on and off. 3. NUMBER buttons Selects programme numbers. 4. MENU Displays a main menu. 5. TV/AV Selects TV, AV1, AV2, S-VIDEO, COMPONENT, RGB-DTV, RGB-PC, RGB-DVl mode. 6. SLEEP button Sets the sleep timer. 7. ENTER Accepts your selection or displays the current mode. 8. VOL+/- button Adjusts the sound level.
OWNER’S MANUAL Remote Control Key Functions TV/AV select button on the remote control Each press of this button changes the mode as shown below AV1 AV2 TV S-VIDEO COMPONENT RGB-DVI RGB-PC RGB-DTV MULTI MEDI select button on the remote control Each press of this button changes the mode as belows.
OWNER’S MANUAL Using the remote control Notes for using the remote control Make sure these are no objects between the remote control and its sensor. Don’t place the remote control near a heater or damp place. Strong impact on the remote control may cause operation failure. Signal from the remote control may be disturbed by sun light or other strong light. In this case, turn the set to other direction.
OWNER’S MANUAL VCR Setup • Connect an antenna or a RCA Cable between the ANTENNA jack on the rear of the TV and the ANTENNA OUT jack on the VCR. • Connect the RCA Jack of the VCR to the RCA AV1 or AV2 of the set. • Press the PLAY button on the VCR. • When connecting the S-VIDEO VCR to the S-VIDEO socket, the picture quality will be further improved. • Connect the S-VIDEO socket of the VCR to the S-VIDEO socket of the set. • Connect the audio cable from the S-VIDEO VCR to the AUDIO sockets of the set.
OWNER’S MANUAL Cable Box Setup • After subscribing to cable TV service from a local provider and installing a converter, you can watch cable TV programs. Connection of external equipment Tips • For further information regarding cable TV service, contact your local cable TV service proviser(s). To watch Cable TV 1 Press TV/AV button on the remote control and select VIDEO source. 2 Tune to cable service provided channels using the cable box.
OWNER’S MANUAL DTV Setup(SET-TOP BOX) - To watch digital broadcast programs, purchase/connect a digital SET-TOP BOX. How to connect a DTV • You can use either the Monitors COMPONENT (DVD/DTV/INPUT) inputs or the single RGB-DTV/PC INPUT for video connections, depending on your Set Top Box connectors. Then, make the corresponding Audio connections. • DTV input is available to 480i/p, 720p, 1080i mode.
OWNER’S MANUAL DVD Setup How to connect a DVD (digital video disk player) • Connect DVD video inputs to Y, Pb, Pr of COMPONENT (DVD/DTV INPUT) and audio inputs to Audio jacks of AV INPUT. • Component Input is available to 480i/p, 720p, 1080i mode. How to use • Press TV/AV button on the remote control of the TV to select COMPONENT. Use the DVD player according to its owner°Øs manual. •Turn on the DVD player, and insert a DVD.
OWNER’S MANUAL PC Setup PC Setup • First, turn on the PC computer and press the ON/OFF button on the TV to apply power to it. Second, turn on the display by pressing the button on the TV or by pressing the POWER button on the TV remote control. • Use the TV/AV button on the remote control to select the RGB-PC input source. • Set the resolution output of the PC to WXGA or under (1366X768, 60Hz). Tips • Avoid keeping a fixed image on the TV screen for a long period of time.
OWNER’S MANUAL DVI Setup[Option] PC Setup • First, turn on the PC computer and press the ON/OFF button on the TV to apply power to it. Second, turn on the display by pressing the button on the TV or by pressing the POWER button on the TV remote control. • Use the TV/AV button on the remote control to select the RGB-PC input source. • Set the resolution output of the PC to WXGA or under (1366X768, 60Hz) Tips • Avoid keeping a fixed image on the TV screen for a long period of time.
OWNER’S MANUAL Turning on the TV - When using the remote control, aim it at the sensor on the TV. Turning on the TV just after installation 1 2 Connect power cord correctly. At this moment, the TV is switched to Standby mode. Press the POWER button on the TV or press the POWER Button or associated with TV button on the remote control and then the TV will be turn on.
OWNER’S MANUAL Checking features 3 4 Press the PR+/- button. Press the VOL ( +) button to select a feature to adjust, and then press the PR+/- buttons to adjust the selected item. • Press the MENU button to exit. Setting Sleep Timer Sleep Timer turns the TV off after a preset time Press the SLEEP button to set sleep time.
OWNER’S MANUAL Adjusting picture control Use APC to set the TV for the best picture appearance APC (Auto Picture Control) 1 2 Press the APC button. Press the APC buttons to select your desired picture condition. CUSTOM • Each press of APC button changes the screen display as shown below. STANDARD SOFT CUSTOM STRONG • You can also select STANDARD, SOFT, CUSTOM or STRONG in the PICTURE menu. Adjusting picture appearance Press the MENU button and then press the VOL+/- button to select PICTURE menu.
OWNER’S MANUAL Auto Sound Control ASC(Auto Sound Control) 1 2 Press the MENU button and then VOL+/- button to select a SOUND setup. Press PR- button and then VOL+ button to select a sound setup. • Each press of ASC or PR+/- button changes the screen display as shown below. STANDARD MUSIC MOVIE SURROUND USER SPEECH • You can also select SURROUND, STANDARD, MUSIC, SPEECH, MOVIE, USER in the SOUND menu.
OWNER’S MANUAL Auto programme tuning Up to 125 TV stations can be stored by programme numbers (1 to 125). Once you have preset the stations, you will be able to use the PR+/PR- or NUMBER buttons to scan the stations you programmed. Stations can be tuned using automatic or manual modes. Note : In some models up to 181 CH stations can be stored. All stations that can be received are stored by this method. It is recommended That you use auto programme during installation of this set.
OWNER’S MANUAL MANUAL programme tuning 4 5 6 7 Press the PR+/- button to select the programme number. Press the VOL+ button to select the ADD and ERASE. Select the desired programme number (1 to 125) with the PR+/- button. Press the ENTER button. Press the PR+/- button to select FINE. Press the VOL+ button. Press the VOL+ button to fine tune for the best picture and sound on the Fine pull-down menu. Press the VOL+ button.
OWNER’S MANUAL Selecting language for the menus Press the MENU button and then press the VOL+/- button to select ETC menu. Press the PR - button. 1 2 3 Press the PR+/- button to select Language and then press the VOL (+ ) button. Press the PR+/- button to select the desired language. Press the ENTER button. Selecting COLOUR TEMP. for the menus Press the MENU button and then press the VOL+/- button to select ETC menu. Press the PR- button.
OWNER’S MANUAL Selecting CLOSED CAPTION for the menus Press the MENU button and then press the VOL+/- button to select ETC menu. Press the PR- button. 1 2 3 Press the PR+/- button to select CLOSED CAPTION and then press the VOL (+ ) button. Press the VOL+/- button to select the desired CLOSED CAPTION. Each press of this button changes the mode as belows. CC2 CC3 CC4 TEXT1 TEXT2 TEXT3 TEXT4 CC1 OFF Press the ENTER button.
OWNER’S MANUAL Selecting PARENTAL CONTROL for the menus 3 Press the PR+/- button to select SET PASSWORD and then press the VOL+ button. Enter your current password using the number buttons on the remote control. (The default password is 0000) Re enter the password to confirm. your new password is active. Press the ENTER button. 4 Press the PR+/- button to select MPAA and then press the VOL+ button. Press the VOL+/- button to select the desired ratings. Press the ENTER button.
OWNER’S MANUAL Selecting PARENTAL CONTROL for the menus 3 Press the PR+ button and then PR+/- button to select AUX CONTROL and then press the VOL+ button. Press the VOL+/- button to select the desired rating. Press the ENTER button. TV Guidelines TV-MA Mature audiences only. This program may contain mature themes, profane language, graphic violence and explicit sexual content. TV-14 Parents strongly cautioned.
Selecting 3D COMB FILTER for the menus Press the MENU button and then press the VOL+/- button to select ETC menu. Press the PR - button. 1 2 3 4 Press the PR+/- button to select 3D COMB FILTER. Press the VOL+ button to select OFF. Press the VOL+ button to change the state of ON or OFF. Press the ENTER button. • ON/OFF state of 3D COMB FILTER is user choice. • It is better to select the 3D COMB FILTER “OFF”, when TV Broadcast is sports, action movie.
OWNER’S MANUAL Selecting PC CONTROL for the menus Press the MENU button and then press the VOL+/- button to select ETC menu. Press the PR- button. 1 2 3 Press the PR+/- button to select PC CONTROL and then press the VOL (+) button. Use the VOL +/- button to make appropriate adjustments and then Press the ENTER button. Press the PR+/- button to select other items. The OSD function for this PC control becomes activated, when the sources are available on RGBDTV/ PC INPUT or DVI-IN external connector.
Selecting CLOCK for the menus 3 4 Press the PR+/- button to select ON TIME and then press the VOL(+) button. Press the PR+/- button to select time and PR, VOL, ON/OFF. Press the ENTER button. Press the PR+/- button to select AUTO SLEEP and then press the VOL(+) button. Press the PR+/- button to select ON/OFF. Press the ENTER button.
OWNER’S MANUAL Setting picture format Press the ARC button to select a desired picture format. • Each time you press ARC button, you can select 16:9 or 4:3 or ZOOM or PANORAMA alternatively. 16:9 16:9 4:3 4:3 ZOOM ZOOM PANORAMA Picture in picture (PIP) function PANORAMA - PIP PICTURE will let you view two seperate inputs on your TV screen at the same time. - Color of main picture may be different from PIP°Øs in PIP PICTURE.
OWNER’S MANUAL Picture in picture (PIP) function Change the main picture and the sub picture Press the SWAP button in PIP mode. When the main picture is TV/AV1/AV2/S-VIDEO, the sub picture input is TV / AV1 /AV2 / S-VIDEO. Twin picture function How to use twin picture Press the SIZE button to select twin picture. Each time you press SIZE button, you can select TWIN or PIP alternatively. • TWIN PICTURE let you view different inputs on your TV screen at the same time.
OWNER’S MANUAL Twin picture function Changing the picture of main and sub picture - PIP/TWIN PICTURE let you view different inputs on your TV screen at the same time. - Color of main picture may be different from PIP’s in PIP/TWIN PICTURE.Press the SWAP button in twin picture mode. - When the main picture input is TV / AV1 / AV2 / S-VIDEO/, the sub picture input is TV/AV1/AV2/S-VIDEO. MULTI PIP This function can be operated when input signal is TV signal.
Troubleshooting Check list Problem Check item No picture on screen and no sound from speakers. �Insert the AC power cord plug securely in AC power outlet. �Make sure the remote control is not in the standby mode (The POWER/Standby indicator is red.) �Turn on the MAIN POWER button on the top of the display. No picture/No picture from AV terminal. �Check the brightness setting of the display. �Lamp may have malfunction.
OWNER’S MANUAL Product specifications Contents Model Name Specification HLT-2672 HLT-3272 Aspect Ratio 16:9 Resolution 1366 X RGB X 768 Receiving channel Low-CH: E2 - S10 VHF High-CH: E5 - S41 Input Terminals UHF CH: E21 - E69 TV 1,0Vp-p / 75Ϊ VIDEO 1,0Vp-p / 75Ϊ S-VIDEO Y: 1,0Vp-p / 75Ϊ C: 0,3Vp-p / 75Ϊ COMPONENT (DVD.
OWNER’S MANUAL Maintenance Guide Cleaning the screen �Always disconnect your TV from any power source when cleaning. �Do not use substances such as glass cleaners, solvents, and thinners,. �Do not apply abrasive or ammonia-based window cleaners. �The screen of your TV has been specially treated, and can be scratched or damaged easily. Wipe the surface gently using only a cleaning cloth or a soft, lint-free cloth. �Do not apply water directly on the screen or any parts of the TV.
OWNER’S MANUAL MEMO