User's Guide

Unfold the board and place cprCUBE
main body matching the logo orientation
접힌 보드를 잘 펴준 뒤, 로고 방향에 맞춰
큐브를 올려 놓습니다.
Compress cprCUBE main body for more
than 3 seconds to activate guide mode
큐브를 3초 간 꾹 누르고 있으면 가이드 모드로
전환됩니다. (가이드 모드가 시작되면 메트로놈
알림음이 반복됩니다.)
COMPOMENTS
① User Guide
② Scenario cards
③ Color ID stickers
④ cprCUBE Board
⑤ cprCUBE main body
Guide for
HOW TO USE
3. Put on the Board
Start guide mode
1. Body rear battery fitting 2. Turn On/Off
Push once to turn on
한 번 눌러 전원을 킵니다.
Push for 2 seconds to turn off
2초 간 눌러 전원을 끕니다.
When the device turn On/Off, LEDs light
and melody sounds
전원 On/Off 시 LED 와 알림벨이 작동 합니다.
The device turns off with no action more
than 10 minutes
10분 이상 동작하지 않으면, 자동으로 꺼집니다.
*Batteries are not included(4 AA batteries needed)
Alkaline batteries are recommended for this product.
AA 배터리는 포함되어 있지 않습니다. (4개 필요)
본 제품은 알카라인 건전지 사용을 권장합니다.
Compression foam
(압박부)
Feedback Component
(피드백부)
⑤
E-mail. [e-mail]
Tel. [phone]
Fax. [phone]
7F ,165, Yeoksam-ro, Gangnam-gu, Seoul
서울특별시 강남구 역삼로 165, 7층 아이엠랩
①
④
②
③
- User Guide-
PRODUCT INFORMATIONPRODUCT INFORMATION
[ Product Information ]
[ Product Specification ]
Product name
Model number
MFR/Country
Certifier Identification code
cprCUBE Pro [특정소출력 무선기기 (무선데이터통신시스템용 무선기기)]
CC3G
I.M.LAB Inc./ South Korea
KC ID: R-C-iML-CC3G
FCC ID: 2ASY3CC3G
1. cprCUBE Board
Dimension
Weight
100×110×0.5 (mm) (Folded)
400×330 (mm) (Unfolded)
17.5g
2. cprCUBE main body
Dimension
Weight
Power supply
Class B Device(B급 기기)
100×100×110(mm)
245g
6.0V , 100mA (4 AA alkaline batteries)
⚠ CAUTION
- Keep the used batteries out of reach of children and dispose separately.
- If you do not use the device for a long period of time remove and store the batteries.
- Do not use a new battery and an old battery together.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF Radiation exposure limits set forth for an uncontrolled environment.
This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.
FCC Part 15.21
Any changes or modifications (including the antennas) to this device that are not expressly approved by the
manufacturer may void the user’s authority to operate the equipment.
FCC Part 15 B
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reason able protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC Part 15.19
RF Specication
- BLE/ 1Mbps
- Frequency 2.4 GHz Band
- Max. RF output power: -13 dBm
Operation Temperature -10~50°C
This device can be operated in at least one Member State without infringing
applicable requirements on the use of radio spectrum.