Quick Guide

G
H
C
A
B
A
B
C
D
E
F
G
H
D
F
i-teamglobal.com
E
PH
PH
Drain and rinse the solution and recovery tanks with fresh water and leave them open.
Remove and clean the filter/float by rinsing it with water.
Remove the deflector gently from the machine and clean it.
Clean the squeegee blade and suction opening with fresh water and a clean cloth.
Detach and clean the brushes and also the bottom of the
brush-deck, now that it is fully exposed.
Check the charge level on the battery indicator.
Recharge the battery as required.
Check the rubbers on the squeegee blade for damage or wear and tear.
Turn them over or replace them entirely when needed.
Clean the wheels on the squeegee blade, make sure the bearings aren’t clogged.
Unscrew the filter from the solution tank and clean it under running water.
Clean the exterior of the imop with a clean cloth and fresh water.
Remove the brushes from the machine and clean the water nozzles
at the bottom of the scrub deck.
If the imop isn’t being used regularly, remove and store the charged
battery in a dry and clean place. Recharge battery at least monthly.
Clean the filter/float
regularly.
Empty the tank before
storing it and empty the
tank before refilling it.
Leave the rubber cap open
when storing overnight so
the tank can vent.
Close the cap of the
recovery tank, otherwise
there’s no water pick-up.
Do not kick the
deck with foot. Gently
lower by hand only.
ALWAYS switch machine
off when not in use or
when in storage.
Do not operate without
filter/float.
Do not use water with pH
below 4 or above 9, and
temperature higher than
45
o
C / 113
o
F.
Solution tank
Recovery tank
Battery pack
Brushes
Squeegee
Control panel
Vacuum filter/float
Deflector
Brush
Turbine
Water
Eco
Operation
Troubleshooting
Fill solution tank.
Max temperature 45
o
C
/ 113
o
F. Ensure pH is
between 4 and 9.
Select operation mode and
you’re ready to go!
Release magnetic connector
for scrub-deck and slowly
lower deck by hand.
Install battery pack:
Slide in the battery pack.
To remove the battery pack:
Pull back blue release clip away from
battery pack. Battery will be ejected.
Attach solution
tank to
magnetic clip.
Install
recovery tank
by attaching to
magnetic clip.
Make sure top
lid is clicked
and closed.
Maintenance and Care daily weekly monthly
The imop won’t start
Check the charge level on the battery indicater. Remove the battery
pack from the machine. Inspect the connectors on the battery and
on the machine for any damage or obstruction. Reinsert the battery
and switch on the machine. Make sure that the battery is charged,
recharge when needed or grab a freshly charged battery. If the
problem still exists we recommend to reset the imop according to
our reset procedure.
Reduced Water Recovery
Please ensure that you have chosen the right cleaning mode and the
vacuum motor is running. Check the recovery tank, when full empty it.
Always empty the recovery tank after cleaning or when you’ve used
up all the solution in the solution tank. Inspect both the deflector and
the air filter, clean when needed. Make sure that the recovery tank
is seated correctly on the machine, and the cap is back on the top
of the tank and is closed properly. Check if hose is connected in the
deflector block. Inspect the rubbers on the squeegee for any damage
or wear and tear and that there is nothing stuck inside the squeegee
blade blocking the airflow. Make sure the wheels are clean and that
they can turn freely. Detach the vacuum hose from the machine and
check both the hose and the opening on the machine.
Insufficient water flow or no water flow
Check if the solution tank is filled and seated correctly on the machine.
Check if the hole in the cap is not obstructed by any dirt. Open and
close the rubber cap to avoid vacuum in the tank. Make sure that the
right operating mode is selected. Remove the brushes and check
the water nozzles on the scrub deck for any obstructions. Empty the
solution tank and check the filter, make sure that it is clean. If the
filter is dirty, please check that it is cleaned monthly or more often, if
required by your circumstances.
Reset
To reset the imop Lite simply remove the battery pack and put it
back in again.
7