Installation Instructions

1 2 3
HOW TO USE THE ISOCKET AUTOSWITCH
1. Plug the i-Socket into any standard 15A/125V outlet.
Set the MODE switch to the AUTO position.
2. Plug vacuum into an ACCESSORY outlet.
Switch ON Vacuum.
3. Plug tool into POWER TOOL outlet.
USE your power tool as normal.
A. Power the tool ON, and the vacuum will automatically start.
B. Power the tool OFF, and the vacuum will continue running
for an additional 7 seconds to clear out the hose.
CAUTION: For indoor use and dry locations only.
Use a 3-prong grounded receptacle only. Failure to heed all
warning instructions could result in serious injury or death.
Warranty: 90 days against manufacturer’s defects.
Register your i-Socket for an extended warranty:
isocketproducts.com/warranty.
INSTRUCCIONES DEL ISOCKET AUTOSWITCH
1. Conecte el i-Socket en cualquier tomacorrient estándar de 15A/125V.
Coloque el interruptor de MODO en la posición AUTO.
2. Enchufe la aspiradora en un enchufe ACCESSORY.
Encender el aspiradora.
3. Enchufe la herramienta eléctrica en el enchufe POWER TOOL.
UTILICE su herramienta eléctrica como de costumbre.
A. Iniciar la herramienta y la aspiradora comenzará a funcionar
automáticamente.
B. Después de detener la herramienta, la aspiradora continuará
funcionando durante unos 7 segundos adicionales para vaciar
la manguera.
ADVERTENCIA: Solo para uso en interiores y lugares secos.
Utilice únicamente un receptáculo de tres patas con conexión
a tierra. No respetar todas las instrucciones de advertencia
podría resultar en lesiones severas o incluso muerte.
Garantía: de 90 días contra defectos del fabricante.
Registre su i-Socket para recibir una garantía extendida:
isocketproducts.com/warranty.
MODE D’EMPLOI L’ ISOCKET AUTOSWITCH
1. Brancher l’ i-Socket à une prise de courant 15A/125VAC.
Mettez l’interrupteur MODE dans la position AUTO.
2. Brancher l’aspirateur dans une prise ACCESSORY.
Allumer l’aspirateur.
3. Brancher l’outil électrique dans la prise POWER TOOL.
UTILISEZ votre outil électrique comme d’habitude.
A. Mettre en marche l’outil et l’aspirateur démarrera
automatiquement.
B. Après l’arrêt de l’outil, l’aspirateur continuera à fonctionner
pendant 7 secondes afin de nettoyer le tuyau d’aspiration.
ATTENTION: A utiliser à l’intérieur et dans des endroits sec.
Toujours utiliser une prise de terre. Ignorer cette mise en
garde annule la garantie et peut creér des risques sérieux
d’électrocution.
Garantie: 90 jours contre les défaults de fabrication.
Enregistrez votre i-Socket pour une garantie prolongeé:
isocketproducts.com/warranty.
Power tool must
have a minimum
continuous power
rating of 60W
B
A
AUTO MAT I C
DUST CONTROL SWITCH
INSTRUCTIONS & SPECIFICATIONS
The i-Socket® wordmark and logo is a registered trademark of
DGC Products Inc. Patents pending.
®2019 DGC Products Inc. All rights reserved.
V1.00
DGC Products, Inc.
5348 Vegas Drive,
Las Vegas, NV 89108
POWER TOOL OUTLET
·
Tool Outlet Connections: 2 or 3 prong plug.
·
Motor rating should not exceed 125V, 15A, 60Hz, 1875W.
·
Power tool must have a minimum continuous
power rating of 60W.
ACCESSORY OUTLETS
·
Controlled by mode switch/power tool.
·
Any standard shop type vacuum (should not exceed 1875W).
·
Dust collector motor should be rated at 125V,
15A and should not exceed 1875W.
MODE SWITCH
·
Controls the Accessory Outlets from AUTO, ON, and OFF.
– AUTO mode enables power tool control.
– ON turns on ACCESSORY outlets independent of power tool.
– OFF turns ACCESSORY outlets o (power tool still usable).
ELECTRICAL SPECIFICATIONS
Outlet Required: Standard 125V, 15A, 60Hz Outlet
Input Connection: 3 prong (grounded) male
Power Rating: 125V, 15A, 60Hz
Actuation Threshold:
~
0.5 Amps (about 60W at 125V)
LED INDICATOR
·
RED Mode LED Indicator
is on when in AUTO Mode.
LED INDICATOR
·
GREEN Accessory LED Indicator is on
when accessory receptacles have power.
Powered By
MODEL# IS-12
If you need further assistance, please email us:
[e-mail]
For technical and alternative use videos,
and to see our full line of products visit:
isocketproducts.com