User's Manual

ManualsBrandsi.Tech Dynamic ManualsAudio EquipmentBLUETOOTH HEADSET

Fig.1

ULC 303

Bluetooth Headset

User Guide

Contents

Product Specifications-----------------------

ULC 303 Overview-----------------------

Getting Started-----------------------

Charging Your Headset----------------------

Indicator Light----------------------

Pairing Your Headset with a Bluetooth Mobile Phone----------------------

Using Your Headset----------------------

Factory Reset----------------------

Troubleshooting----------------------

Safety Information----------------------

Care and Maintenance----------------------

Declaration of Conformity----------------------

Product Specifications

Bluetooth Specification: v2.0 Class 2 + EDR

Bluetooth Profiles Supported: Headset and Handsfree

Range of Frequency: 2.4GHz spectrum

Nominal Charging Time: Within 3 hours

Talk Time*: Up to 4.5 hours

Standby Time*: Up to 90 hours

Dimensions: 44 (L) x 20.5 (W) x 11.3 (H) mm

Weight: 8.9 grams

* may vary due to the user’s habit, different modes of operation, and mobile phone

settings.

ULC 303 Overview

1. Multi-function Button (MFB)

• Power On / Off

• Pair with mobile phone

• Answer / End a call

• Last number redial

• Voice dialing

Summary of content (8 pages)

PAGE 1
ULC 303 Bluetooth Headset User Guide Contents Product Specifications----------------------ULC 303 Overview----------------------Getting Started----------------------Charging Your Headset---------------------Indicator Light---------------------Pairing Your Headset with a Bluetooth Mobile Phone---------------------Using Your Headset---------------------Factory Reset---------------------Troubleshooting---------------------Safety Information---------------------Care and Maintenance---------------------Declarati
PAGE 2
. 3. 4. 5. 6. 7. Volume Key • Adjust volume • Reject / Transfer a call Status Indicator Built- in Rechargeable Battery Microphone Charging Socket Speaker Getting Started To use your ULC 303 Bluetooth headset (“headset”), please follow the steps below: 1. Ensure your headset is fully charged. 2. Pair your charged headset with a Bluetooth-enabled mobile phone. Charging Your Headset The headset comes with a built- in rechargeable battery.
PAGE 3
Pairing Your Headset with a Bluetooth Mobile Phone 1) Ensure the headset is off. 2) To activate the pairing mode, press and hold the headset’s MFB for 8 seconds without releasing your finger until its status indicator flashes green and red light alternately. 3) Activate your mobile phone’s Bluetooth, search Bluetooth devices, select “ULC 303” and enter the passcode “0000”. When the pairing is completed, the headset’s status indicator will flash green light rapidly five times.
PAGE 4
(mobile phone to once headset)* * Subject to mobile support Factory Reset You may reset the headset to its default settings. Resetting will also remove the pairing history of your headset with the mobile phone. 1. Hold the volume key and plug charging cable into the charging socket. The status indicator will flash Green 3 times. 2. Release the volume key. 3. The status indicator will stay Green again and the headset is reset. i.Tech Bluetooth headset is designed to work with Bluetooth devices.
PAGE 5
doesn’t response. • Plug charging cable into the charging socket Safety Information • Check and observe local laws regarding the use of a mobile phone and a headset while driving. If you use the headset while driving, ensure your full attention and focus. It is your responsibility to drive safely. Consider to pull off the road before making or answering a call. • Never leave your headset above any air bag deployment area inside your car as serious injury may result when an air bag deploys.
PAGE 6
• • • • • • • • • • • • accidentally depressed, your mobile phone may place an unintended call. Do not expose the headset to liquid, moisture or humidity, or rain as it is not waterproof. Do not use abrasive cleaners to clean the headset. Do not expose the headset to extremely high or low temperatures. Do not leave the headset in direct sunlight for an extended period of time. Do not leave the headset near open flames such as cooking burners.
PAGE 7
i.Tech ULC 303 Model No.: C51-B303-XX is in conformity with the following essential requirements of Council Directive 1999/5/EC (referred to as R&TTE Directive): Article 3.1a, 3.1.b and 3.2. and the product is manufactured in accordance with Annex II of the above directive. A copy of the Declaration of Conformity can be found at http://www.itechdynamic.com.
PAGE 8
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna.