User's Manual Part 2

ManualsBrandsI-Tel ManualsElectronics5.8 GHz FHSS Cordless Phone

This section is a reference guide to the basic functions and operations of your cordless

telephone. For more detailed descriptions of the operations and features of this telephone, refer

to the Contents on page 1.

1. Carefully remove your cordless telephone from its shipping carton. If there is any visible

damage, do not attempt to operate this equipment. Return it to the place of purchase.

2. Check to be sure you have all items that come with this cordless telephone system. You

should have four HANDSETS, BASE UNIT, four AC/DC ADAPTERS, three CHARGER

UNITS, TELEPHONE LINE CORD, SHORT TELEPHONE LINE CORD, four BELT CLIPS,

and an Owner’s Manual.

3. Insert the small plug on the end of the AC/DC ADAPTER(9V DC, 500 mA) into the POWER-

IN CONNECTION JACK at the back of the BASE UNIT.

4. Plug the AC/DC ADAPTER into a 120V AC wall outlet.

USE ONLY WITH CLASS 2 POWER SOURCE 9V DC, 500 mA for the BASE UNIT.

USE ONLY WITH CLASS 2 POWER SOURCE 9V DC, 100 mA for the CHARGER.

5. Insert one plug of the TELEPHONE LINE CORD into the house telephone jack and the

other end into the TELEPHONE LINE CONNECTION JACK at the back of the BASE UNIT.

(If you have an older 4-prong telephone jack, you will need an RJ-11C telephone jack

adapter. This adapter is available at the same place you purchased your telephone.)

6. We recommend not placing this unit next to appliances. Doing so may cause interference.

TELEPHONE

LINE CORD

SHORT TELEPHONE

LINE CORD

BELT CLIP (4)

AC ADAPTER (4)

BATTERY

PACK

HANDSET (4)

BASE UNIT

CHARGER (3)

Summary of content (15 pages)

PAGE 1
Getting Started Connecting Your Phone This section is a reference guide to the basic functions and operations of your cordless telephone. For more detailed descriptions of the operations and features of this telephone, refer to the Contents on page 1. 1. Carefully remove your cordless telephone from its shipping carton. If there is any visible damage, do not attempt to operate this equipment. Return it to the place of purchase. 2.
PAGE 2
Remote Control Operation Remote Operation through a Tone Telephone You can use many Answering System features when you are away from home. To protect your privacy, most of the features can be used only after you enter the three-digit Remote Access Code. Remote Access Codes The Remote Access Codes are preset at the factory as below. You can use the preset codes or choose your own.
PAGE 3
Remote Control Operation Using the Remote Instruction Code 1. Dial your telephone number. 2. Listen to or bypass the OGM in the PRIMARY MAILBOX by entering your Remote Access Code. 3. A “beep” will sound when your Remote Access Code is correctly accepted by your Answering System. 4. If the announcement does not stop, enter the Remote Access Code again. 5. The Answering System will request that you enter the Instruction Code or press “0” for help. A.
PAGE 4
Speakerphone Operation Speakerphone Operation This telephone allows you to answer calls using the BASE UNIT speakerphone function. 1. When the phone rings, press the spkr button. 2. Start your conversation. 3. To end your conversation, press the NOTE: Press the or spkr button again. button to adjust the BASE UNIT speaker volume to a comfortable listening level.
PAGE 5
Recharging the BATTERY PACK Battery Type Use the following type and size of BATTERY PACK: Cordless Telephone BATTERY PACK 3.6V, 600mAh U.S. Electronics Inc. Ni-MH Battery Pack: Model B655 (GP60AAAH3BML) This BATTERY PACK is available through: U.S. Electronics Service Center 105 Madison Avenue New York, NY 10016 1-800-828-5208 NOTES: 1. During a power interruption, the BASE UNIT does not operate, and a phone conversation cannot be made on the HANDSET. 2.
PAGE 6
Changing the BATTERY PACK Changing the Battery Pack The BATTERY PACK provides power for the HANDSET of your cordless telephone. To Replace BATTERY PACK: 1. Remove the HANDSET BATTERY COMPARTMENT COVER by sliding it down. 2. Pull out the BATTERY PACK PLUG and remove the BATTERY PACK. 3. Plug the new BATTERY PACK into the BATTERY CONNECTOR. 4. Slide the HANDSET BATTERY COMPARTMENT COVER firmly into place in its closed position. 5. Before use, charge the new BATTERY PACK for 12 hours.
PAGE 7
Problem Solving Problem Solving Section For your assistance, we have listed below a few common problems. Phone does not work, check the following: 1. 2. 3. 4. BASE UNIT is plugged into a power source. HANDSET is charged. TONE/PULSE Select switch is in the right position. TELEPHONE LINE CORD is plugged into the TELEPHONE JACK. Range of phone limited, check the following: 1. BASE UNIT is centrally located in your residence. 2. BASE UNIT is not located near appliances.
PAGE 8
Problem Solving Answering System does not work, check the following: 1. BASE UNIT is plugged into a power source. Answering System does not answer calls, check the following: 1. ANSWER ON/OFF LED indicator is lit. Answers calls only after 10 rings, check the following: 1. ANSWER ON/OFF LED indicator is lit. 2. Message Memory is not full. Does not respond to remote commands, ensure the following: 1. Correct Remote Access Code is entered. 2. A TONE telephone is being used.
PAGE 9
Technical Information Technical Information This cordless telephone uses radio frequencies to allow mobility. There are certain difficulties in using radio frequencies with a cordless telephone. While these are normal, the following could affect the operation of your system. Noise Electrical pulse noise is present in most homes at one time or another. This noise is most intense during electrical storms.
PAGE 10
FCC Requirements Federal Communications Commission Requirements This equipment complies with Part 68 of the FCC rules. A label on the BASE UNIT of the equipment contains, among other information, the ACTA Product Number and the Ringer Equivalence Number (REN) for this equipment. You must, upon request, provide this information to your telephone service provider.
PAGE 11
FCC Requirements Federal Communications Commission Requirements (continued) CAUTION: Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
PAGE 12
Warranty Warranty Information BellSouth Products One-Year Limited Warranty This limited warranty sets forth all BellSouth Products responsibilities regarding your telephone. There are no other expressed or implied warranties from BellSouth Products. Warranty Service Provided If you purchased the telephone new from a retail vendor, BellSouth Products warrants the telephone against defects in material and workmanship for a period of one (1) year from the original date of purchase.
PAGE 13
Warranty What To Do for Warranty Service During the first thirty (30) days, a defective product is eligible for over-the-counter exchange at the retailer from whom it was purchased. After thirty (30) days, the defective product should be returned to the authorized service center. Please allow 2-3 weeks for the return of your telephone product. The shipping address of the authorized service center is: U.S.
PAGE 14
IMPORTANT In order to get maximum life from the HANDSET BATTERY PACK, be sure to charge the HANDSET for 12 hours before initial use. IMPORTANT Placing your BASE UNIT near appliances such as another telephone, televisions, refrigerators, radios, or microwave ovens may cause interference. IMPORTANT To obtain better sound quality for locally recorded (OGMs and Memos) message, speak directly into the MICROPHONE from a distance of 9 to 12 inches.
PAGE 15
STOP Make certain you receive the best performance from your telephone. Read this manual first. Visit Us on the Web: www.uselectronics.