5/3/2-MEGA PIXELS NETWORK CAMERA IR-5MIP566/ IR-3MIP566 IR-5/2MIPN/2MIPS/3MIPW42 USER MENU Version: V1.3 Doc. No.
Safety information This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit. Megapixels This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING To prevent damage that may result in fire or electric shock hazard, do not expose this appliance to rain or moisture.
filled with water on top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects. 7. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service center. Continued use in such a condition may cause fire or electric shock. 8. If this product fails to operate normally, contact the nearest service center and never disassemble or modify this product in any way.
IMPORTANT SAFETY INSTRUCTIONS Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, or other apparatus (Including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug.
SAFETY INFORMATION FCC STATEMENT This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received including interference that may cause undesired operation. CAUTION This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of FCC Rules.
About This Guide Conventions used in this guide To make sure that you perform certain tasks properly, take note of the following symbols to use throughout this manual. WARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: Information to prevent damage to the components when trying to complete a task. IMPORTANT: Information that you must follow to complete a task. NOTE: Tips and additional information to aid in completing a task.
Table of Contents Chapter 1. Introduction ---------------------------------------------------------------------------------------- 8 1-1. Highlights of your new Network IP Camera ------------------------------------------------ 8 1-2. Product Specification --------------------------------------------------------------------------- 9 1-3. Packaging Contents --------------------------------------------------------------------------- 18 1-4.
Chapter 1. Introduction 1-1.Highlights of your new Network IP Camera Congratulates on purchasing this high-resolution 5M pixels network IP Camera! This IP Camera provides 5-Mega pixels high-resolution video quality, with its advanced megapixel lens; you can view remote images in more detail than conventional close-circuit cameras. Other highlights of this network IP Camera include: Onvif compliant. Built-in 802.3af compliant PoE Two way audio support. IP67 waterproofing criterion.
1-2. Product Specification IR-5MIPN42 Series System Platform: TI DM368 SoC CPU; Linux Embedded O.S. Image Device 1/2.5" 5 M pixels (2592x 1944 pixels) progressive CMOS sensor. Video Setting Compression: Video: 0.1M ~ 12M bits/sec (CBR/VBR/LBR configurable) H.264 μ HP/MP/BP, M-JPEG; Audio: G.711 -low/a-low Codec Resolution: Main Streaming: 2592×1920, 2048×1536, 1920×1080, 1280×720. Sub streaming: 320×288, 320*240 Frame Rate: 5-Mega: 10 fps; 3-Mega: 20 fps; 1080p: 30 fps @ H.
I/O Port Standard: Audio in (2Vp-p); Audio out (30mW/600 Ω); DC power in, RJ-45 (LED indicates power /linking status). Full function: Alarm in x1; Alarm out x1; TV out, Reset button, Video out, SD Card slot. (IR-5MIPN42-Fxxxx-F) Option: USB for Wi-Fi device Surge Protector Video: Peak Inverse Blocking Voltage: VPIB= 100V; Peak Pulse Current: Ipp=44A; Clamping Voltage: 10V @ Ipp= 5A. Power: Maximum Energy: 3.6J @10/1000µs; Clamping Voltage: 16.8KA(1-Time)/8.
Housing Waterproof IP67 housing with anti-cut cable and 3-Axis bracket. Dimension/Weight 310mm (L) x 100 mm (W) x 85 mm (H) / 0.98Kg; (Including bracket). Operation Power: Maximum 3 W & 8W(IR LED On); PoE IEEE 802.3af Class 3; DV12V Temperature: Temperature -10°C ~ 50°C; Humidity 20% ~ 80% RH. IR-2MIPN42 Series System Platform: TI DM365 SoC CPU; Linux Embedded O.S. Image Device 1/3" 1.3 M pixels (1280x 960 pixels) progressive CMOS sensor. Video Setting Compression: Video: 0.
External Microphone input; Speaker output. Ω impedance. 2Vp-p audio input and audio output with 600 Network Protocol: HTTP, HTTPS, TCP/ IP, IPv4, IPv6, UDP, SMTP, FTP, DHCP, DDNS, NTP, DNS, SNMP, RTSP, RTP/RTCP, Bonjour, PPPoE, QoS, UPnP, IGMP; uPnP and 802.1x. Interface: 10BASE-T/100 BASE-TX; Wi-Fi (Via USB optional) Compatible: Onvif compliant. I/O Port Standard: Audio in (2Vp-p); Audio out (30mW/600 Ω); DC power in, RJ-45 (LED indicates power /linking status).
Time management: Manual Time Setting; Time Server and NTP support; Real Time Clock. Event management: Events triggered by motion detection or sensor configured by schedule. Event notification: Notify to FTP, email, Samba server or Digital output triggered. Update: Support Firmware update. Browse I.E. 7.0 above; Safair Browser, Firefox and Chrome V3.0 above with plug in. Housing Waterproof IP67 housing with anti-cut cable and 3-Axis bracket. Dimension/Weight 310mm (L) x 100 mm (W) x 85 mm (H) / 0.
D-WDR: 76dB Overlay: Text / Time Stamp Audio Setting μ-Low/ a-Low G.711 audio encoding and decoding; 2-way audio. External Microphone input; Speaker output. Ω impedance. 2Vp-p audio input and audio output with 600 Network Protocol: HTTP, HTTPS, TCP/ IP, IPv4, IPv6, UDP, SMTP, FTP, DHCP, DDNS, NTP, DNS, SNMP, RTSP, RTP/RTCP, Bonjour, PPPoE, QoS, UPnP, IGMP; uPnP and 802.1x. Interface: 10BASE-T/100 BASE-TX; Wi-Fi (Via USB optional) Compatible: Onvif compliant.
Storage Micro SD slot for SD/SDHC card storage; Support Pre-recording and Post recording; Network failed start recording on SD card, Backup/Restore to device configuration file, Backup, Upload data to FTP/SMTP sever. Management Time management: Manual Time Setting; Time Server and NTP support; Real Time Clock. Event management: Events triggered by motion detection or sensor configured by schedule. Event notification: Notify to FTP, email, Samba server or Digital output triggered.
Sub streaming: 320×288, 320*240 Frame Rate: 3-Mega: 20 fps; 1080p: 30 fps @ H.264/M-JPEG Mode; Frame rate can be adjustable by user. Streaming: Multi-Stream H.264 Base/Main/High Profile and Motion JPEG video streaming Control: Brightness, Contrast, Saturation, Sharpness, Exposure, Motion detection, Mirror, Shutter, Privacy mask, Flickerless, Noise reduction, IRIS, AES, AWB, AGC, BLC, WDR, ROI, Audio gain, Alarm in/out Color: 0.2 Lux 1/F1.2 B/W: 0 Lux. (IR LED on) . WDR: 83.
16.8KA(1-Time)/8.4KA(2-Times) @8/20µs (1 Time); Insulation Resistance: 10000M Ω. ≧ Lens & IR Illuminators 〜 〜 f=2.8〜12 mm/ F1.2〜F2.8 (IR-3MIPW42-F0312 & IR-3MIPW42-F0312-F ); Lens: f=3 9 mm/ F1.2 F2.3 (IR-3MIPW42-F0309 & IR-3MIPW42-F0309-F ); f= 4mm; 6mm, 8mm, 12mm/ F1.8 (Optional) (IR-3MIPW42-F04/06/08/12). IR Cut: Built on removable IR-cut filter for day & night function. IR Illuminators: 42 pieces IR LED Illuminators.
1-3. Packaging Contents Please check the contents of your new Network IP Camera when you unpack the package. If any item is missing, please contact your dealer of purchase for help. The package includes the following items: Network IP Camera x 1ea Bundle NVR & CMS software CD x 1ea User manual x 1ea Accessory package x 1 set Anchor 7x27 * 3 ea Screw 4 x27 Tp1 Bnd Sus *3 ea Hexagon wrench 3.0mm L type * 1 ea Mount hole sticker * 1ea 1-4.
1-5. Product Parts Description Front side items description: 1. Sunshield: It protects the camera from the direct sunlight. 2. Sunshield Hold: It fixed the sunshield with the camera. 3. IR LED: These infrared LED’s are controlled by the illumination sensor. 4. Illumination Sensor: Detects incoming light to control the IRLED. Cable (Standard version) 1. Audio in cable: Plug microphone into audio in.
2. Power cable: Connect to DC12V power adapter when use none POE Hub 3. Network port: Plug the RJ-45 LAN cable of POE switch Hub. The Green LED on for power OK; Green LED flash for communication. 4. Audio out cable: Plug microphone into audio in and speaker into audio out. Cables: (for Full function IP camera) 1. Audio in & out cable: Plug microphone into audio in and speaker into audio out. 2. Network port: Plug the RJ-45 LAN cable of POE switch Hub.
Chapter 2. Camera Installation 2-1. Wall Mount installation Fix the camera This camera is waterproof and in compliance with the IP66 spec, but the jack connected to the external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed. 1) Paste the mount hole sticker on the position that you want to install.
Adjust camera angle from bracket mount (Please refer the photo as below) 1) Use the Hexagon wrench to loosen the bolt and to rotate the bracket to suitable position. 2) Adjust horizontal, vertical or rotate camera body angle of the camera. 3) Use the Hexagon wrench to tighten a bolt after adjusting the camera. Adjust the Lens’s zoom and focus (Please refer the photo as below) 1) Remove the sunshield from the camera. 2) Remove the front cover from the camera by turning it counterclockwise.
Chapter 3. Running IP Camera by Witness Pro NVR software 3-1. Network Deployment General Connection (without PoE) 1. Connect RJ45 Ethernet cable to a switch. Use a Category 5 Cross Cable when your network camera is directly connected to PC. 2. Connect the power cable from the Network Camera to a power outlet. 3.
3-2.Install Witness Pro NVR software You can use your new Network IP Camera by its web user interface v There is a NVR software CD comes with IP camera which allow you run 32/64 channels IP cameras on a PC. Please follow the steps below to complete the installation of Witness Pro NVR software. While into Windows, and insert the I-View DVR software CD into a CD/DVD drive. Select the NVR64 or NVR32 software . Fig. 1-3-1.1 Installation Menu Step 3.
Step 5. Click the “Browse” button to install into a different directory, otherwise click on the “Next” button to install the software into the proposed director. Fig. 1-3-1.5 Installation Step 6. Select “No, I will restart my computer later” and press on the “Finish” button to exit. Fig. 1-3-1.
3-3. Setting IP camera for Witness Pro NVR software Click “ Start “ >> “ All Programs” >> “Witness NVR32 Pro”, then select the “ Video Parameters setup-ezSetup” accessory program to setup the parameters. You will see the diagram as below Fig A Fig B Disable channel: This will disable the selected channel when enable this function. Install video codec: Install the video codec, if you connect IP camera at first time. Vendor & Model: Select the correct brand and model for the connected IP camera.
used camera support Onvif compliant from: http://www.onvif.org. Click “ Onvif setup “ icon to setup the parameters which you want to run on the Hybrid DVR or NVR. Compress: Select the suitable codec for video recording and transmission. Recording resolution: Select the resolution for video recording and display. Frame rate: Select the frame rate for video recording and display. Rate Control: You can choice video quality or bit rate from this tab.
setting process. For the detail information, please refer to the IP camera operation menu. HTTP port & RTSP port: The both port number must be matched the setting of IP camera.. Display streaming: You can select the “Dual streaming” or “Same as recording” mode; If you select the “Dual streaming” mode, the live display video will show lower resolution (320*240) for split video and higher resolution (same as recording resolution; such as 1920*1080) for pop-up to single video on the screen.
Chapter 4. Running IP Camera by I.E. Browser You can use your new Network IP Camera by its web user interface via I.E. web browser. The requirements for viewing IP camera are as below: OS: Microsoft Windows 2000/XP/Vista/7/8. Browser: IE6 or above. Cell phone: 3GPP player. Chrome V3.0 or above with plug in. You must know the IP address of IP Camera before you can connect to it. The IP Camera will use DHCP server on your local network to obtain an IP address automatically by default.
Step 2. Press “Search “button to search for all IP Cameras on your local network. Step 3. If you need to change IP address, double click the Mouse on the selected IP Camera and then change the IP address and Gateway IP, then click the “OK” button to save the setting. Step 4. If you no longer need to use this utility, click “Exit” button to close it. .The default User name / Password is “ admin / 123456 “ and IP address is 192.168.0.123.
IE 8 and earlier version: Right click the indication bar and click: “Install This Add-on for All Users on This Computer…” to install ActiveX plug-in. IE 9 version: Click ‘Install’ button located at the bottom of I.E. to install ActiveX plug-in. If you’re prompted that the Windows Firewall has blocked some features of this program’ Click “Allow access” button to enable the IP Camera function properly. When you’re installing Internet Explorer plug-in, you may also be prompted the diagram.
IE 10 version: Click ‘Install’ button located at the bottom of I.E. to install ActiveX plug-in. You need to do the process as below: Click “Internet options” section, then choice “ Security “ tab >> “ Trusted sites “ and change the bar to “Low”. Click “ Sites “ to add the trusted site for this IP camera. Please refer to the diagram.
4-2. The Function Description of Live Window After ActiveX plug-in is installed, you should be able to see the live video from IP camera as below window. 1 2 3 4 5 6 7 8 9 10 11 12 This section introduces the function buttons of live window. You can test the IP camera function from your Brower. The button functions are as below: 1. Listen: Click this icon to listen the audio from IP camera when Microphone had installed. 2.
7. Screen: Choice the video streaming on the screen. 8. View: Click this icon to display the video of IP camera. 9. Play Mode: Click this icon to choice the display speed or video quality will be priority first. 10.Setup: Click this icon to setup the parameters of IP camera. 11.Pan/Tilt/Zoom button: Move the Pan/Tilt/Zoom position of IP Speed dome camera, this function just effect for the IP PTZ camera only and the detail description as below. 12.Exit: Click this icon to exit the I.E. browser viewing.
4-3. The Network setup Function Description Click “ Setup “ icon to start setup the parameters of IP camera. You can configure basic IP camera settings like data transfer protocol and data storage folder…etc. Device Info: Click this button to check the current Mac number, Firmware version, model, and also allow you entry the camera name on the “Device name:” tab. Click Save to change the setting.
configured before you operate the IP camera over network. IPv4 and IPv6 are both supported. Configure the NIC settings, including the IPv4 (IPv6) Address, IPv4(IPv6) Subnet Mask and IPv4(IPv6) Default Gateway. Click Save to change the setting. 1. If the DHCP server is available, you can check to automatically obtain an IP address and other network settings from that server. 2. The valid value range of Maximum Transmission Unit (MTU) is 500 ~ 9676. 3.
click Save to change the setting. QoS: Click this button to adjust the QoS (Quality of Service) volume and it can help solve the network delay and network congestion by configuring the priority of data sending the audio and video and control command. The valid DSCP value ranges from 0 to 63. The DSCP value is bigger, the priority is higher. Click Save to change the setting.
(2) Set the date of the DST period then click to save the settings. Manual setup: Configuring Time Synchronization Manually. (1) Check the Manual Time checkbox. (2) Click to set the system time from the pop-up calendar and then click to save the settings. You can also click the Save icon with computer time checkbox to synchronize the time of the IP Camera with the time of your computer. PC Time: Select this item and IP camera will synchronize the Date/ Time with your computer’s (or NVR) time as its time.
UPnP: Click this button to enable the UPnP (Universal Plug and Play) function. UPnP™ is a networking architecture that provides compatibility among networking equipment, software and other hardware devices. The UPnP protocol allows devices to connect seamlessly and to simplify the implementation of networks in the house and corporate environments. With the function enabled, you don’t need to configure the port mapping for each port, and the camera is connected to the Wide Area Network via the router. 1.
Before you start, please registration on the DDNS server is required before configuring the DDNS settings of the IP Camera. Please do the process to setup the DDNS. (1) Enter the DDNS Settings interface: (2) In the Domain text field, enter the domain name obtained from the DDNS website. (3) Enter the Port, User Name, Password registered on the DDNS website and the check interval period of DDNS server. Click to save the settings.
Mobile Phone Viewer: Click this button to enable IP camera for the mobile or Table PC remote viewing, this function can suit for the Android, iPhone Mobile phone and i-Pad Table PC. Entry the UID number or scan QR code into your mobile App, then you can remote viewing /Recording the IP camera video and also can control the PTZ IP camera. .
Streaming: Configuring Video streaming settings as below: Source Resolution: Select video main streaming resolution from the drop menu. Streaming ID: Streaming 1 means is the “ Main Streaming “ that for the recording purpose. The streaming 2 means is the “ Sub streaming” that is for the remote viewing from Internet when bandwidth is not enough or split video display to reduce the system loading. Video Encode: The Video Encoding standard can be set to H.264 or MJPEG.
higher bitrates (and therefore more storage space) to be allocated to the more complex segments of media files while less space is allocated to less complex segments. CBR (Constant Bit Rate): The rate at which a codec's output data is constant. CBR would not be the optimal choice for storage as it would not allocate enough data for complex sections (resulting in degraded quality) while wasting data on simple sections. Bit Rate mode: Set the max. Bitrate to 200~12000 Kbps.
Scene setup: White balance: There are some scene modes to difference environments, such as Auto, Cloudy, Sunny, Tungsten and Fluorescent mode WDR: Allow to enable /disable WDR function. Flickless: Set the Video Standard to 50hz(PAL) or 60hz(NTSC) according to the video system in your country, Wrong frequency will show the scrolling lines on the video. Noise reduction: The noise reduction function processes the noise between two frames besides processing the noise in one frame.
OSD: Allow to paste text (Device name) and time stamp on the video. Basic setup: You can choice the font size and transparency for the text (Device name) and time stamp which you want to show on the video of IP camera. System setup: Allow enable/disable the “Device name” and “Time stamp” to paste on video; and you also can setup the display position. The left/top is original position of X/Y axis. Allow user to define the time format and paste text position.
Privacy Mask: Privacy mask enables you to cover certain areas on the live video to prevent certain spots in the surveillance area from being live viewed and recorded. Enable Privacy mask function, click and drop the left button of Mouse for setup up the mask. Allow setup several mask areas, but the total areas cannot exceed 5% of image. Video system: Choice the video system for the TV out (Composite signal). . The maximum frame rate will be 30 fps when choice the NTSC mode and 25fps at the PAL mode.
I/O & PTZ setup: You can setup the alarm input/output and PTZ protocol from this section. PTZ: Setup the PTZ parameters such as Baud rate, protocol and ID address. (Option) Alarm I/O: Alarm input: Setup the name of alarm input and define the level of trigger single. Alarm output: Setup the name of alarm output; define the mode (NC or NO) and trigger period. (0 ms: Continue trigger) Alarm Trigger: You can setup the image motion trigger and sensor alarm trigger from this section.
Motion alarm: Enable Motion detection function and you can setup the trigger schedule and detection area. Click and drag the left button of Mouse to setup the detection and you also can select the motion sensitivity. You can specify the linkage method (Such as Trigger alarm output, move the PTZ camera preset position and notify via email) when an event occurs. Alarm trigger: The alarm trigger almost same as Motion alarm, please refer the description of Motion alarm section.
Recording: Click this button to setup the type of triggered recording, storage media and schedule recording. You can setup the Pre recording & Post recording period with the video and picture format on difference storage device. Please refer the detail process as below: Recording: Enable the” Schedule” recording and you can select “Continue recording “, “ Start recording when network failed” and “ Schedule recording “ mode.
For example, if an alarm triggers recording at 10:00, and the pre-record time is set as 5 seconds, the IP Camera starts to record at 9:59:55. Post-record: The time you set to stop recording after the scheduled time or the event. For example, if an alarm triggered recording ends at 11:00, and the post-record time is set as 5 seconds, the IP Camera records until 11:00:05. Overwrite: If you enable his function and the HDD is full, the new record files overwrite the oldest record files automatically.
“FTP server”: Setup the recording path via FTP server mode. The detail information of FTP server, maybe need to ask the MSI people. “SD Card ”: Setup the recording path on SD Card. You need to format the SD card from the IP camera before you used. Local path: Setup the saving path of video clips and snapshot on the PC which connect this IP camera. Authority: Setup authorized users and group from this section.
User: Click this button to create a new user or delete/ modify available user. There are three user accounts, Media user, Operator and Administer. Protocol: The IP camera support the Onvif protocol and you will find out the version. Maintenance: Click this button to update the firmware, restore the default setting and check the view log …etc. Please refer the detail process as below: Reboot: There are 2 choices to reboot the IP Camera, one is menu, the other by schedule setting.
Reset: You can choice reset the IP address or all parameters become to the default setting. Click the “ Reset IP address “ icon just let the IP address only become to default only, the reset parameters will keep the used setting. Click the “Reset “ icon the IP camera setting become to default. Clicking Reset icon will restores all the parameters to default settings including the IP address and user information. Please use this button with caution.
Chapter 5. Troubleshooting Before you send this IP Camera back to your dealer when you found this IP Camera is not working properly, please checks the table as below to save your time. Problem description Can’t connect to IP Camera Possible solution(s) Check the IP address and port number is correct or not Make sure the entry User name/Password is correct. Make sure the port number is opened from the NVR and Router. Make sure the network cable is correctly connected to your local area network.
