Operating Instructions PAC-080M The lighting flash with CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN TO REDUCE THE RISK OF ELECTRICAL SHOCK DO NOT REMOVE COVER NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL arrowhead within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons The exclamation point within a triangle is intended to tell the user that important operating Version: V1.
Table of Contents About This Guide ------------------------------------------------------------------------------------------------- 3 Customer Support ------------------------------------------------------------------------------------------------ 3 FCC Compliance Statement ------------------------------------------------------------------------------------ 4 FCC Warning ------------------------------------------------------------------------------------------------------ 4 Trademark ----------------------
About This Guide Please follow the instructions in this manual to obtain the optimum results from this unit. We also recommend that you keep this manual handy for future reference. Conventions used in this guide To make sure that you perform certain tasks properly, take note of the following symbols to use throughout this manual. WARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: Information to prevent damage to the components when trying to complete a task.
FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation. FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Chapter 1. General Description The PCM-080M Intelligent Mix Amplify delivers up to 120 watts of output audio power and control 8 Zones Speakers. The audio output terminals block allow connecting 8-ohm/100- or 70-volt (Selectable) speaker, or speaker distribution systems and can be rack mounted by using rack mounting bracket. The PCM-080M Intelligent Mix Amplify can integrate with I-View’s DVR series become to a P.A. DVR system.
1-2. Product Specification Item \ Model Audio Output (RMS) PAC-080M Max. 120W; 100V / 70V (Selectable) with 8 zones output ports. Total impedance loading less than 100V/83Ω; 70v/41.5Ω ≦ 1% @ 1K Hz (1/3 Rated power) T. H. D.
Chapter 2. General Installation 2-1.
2-2. Nomenclature Description 1 ○ 2 ○ 3 ○ 4 5 6 ○ ○ ○ 7 ○ 8 ○ 9 ○ 1 MIC Volume Controls: Adjust gain of Microphone input. ○ 2 TEL Volume Controls: Adjust gain of Telephone input. ○ 3 AUX Volume Controls: Adjust gain of Computer’s sound card. ○ 4 Bass Control: Modifies bass response. Turn clockwise to boost, counter-clockwise to attenuate ○ the bass response. Tone is flat at center. 5 Treble Control: Modifies treble response.
10 ○ 11 ○ 12 ○ 13 ○ 14 ○ 1 ○ 2 ○ 3 ○ 4 ○ 1 AC Outlet: Connects to AC 115V or AC230V power source. ○ 5○ 6 ○ 7 ○ 8 ○ 9 ○ The supply transformer has been designed for use on either 115Vac or 230Vac, selected by slide switch on rear panel. The amplifier is factory set at 230Vac mains voltage. The connection cable must be fitted with an in-line fuse. Quick blow type F10A when Connecting batteries please ensure correct polarity.
1. Use only 100V or 70V (Selectable) Line Loudspeakers and total impedance loading less than 100V/83Ω & 70V/41.5Ω. 2. The Zone 8 can connect the PAC-040S Extension box to increase the speaker zones or save the cable cost. The Zone 8 will be no function when connect to PAC-040S. 3. The default output voltage of speaker is AC100V. You need to turn to 70V from inside switch of PAC-080M audio amplify if you use the 70V speaker. Call your local dealer for this service.
pin assignment of MIC input as diagram. 1. The MIC inputs is balanced standard XLR Jack and 1mV@ 600 Ω. Impedance. 2. The MIC input has VOX priority which will override TEL and AUX input signals. 3. The defaults all speaker zones are on when announcement via this port and you can change the setting from P.A. DVR software. 10 Voltage Selected Switch: Select AC115V or AC230V and voltage will show on switcher. ○ 11 ○ USB port: Connect to the USB port of DVR via USB cable.
2-3. Operation The amplifier should never be placed in areas. Never block ventilation holes. Never to exposed to direct sunlight. Never with high humidity or dust levels. Never with high ambient temperatures. Never susceptible to vibration. Never with poor ventilation. Never adjacent to heat-generating equipment. 1. Connect Connects to earth-ground by shorter than 10 feet 16AWG or thicker cable. 2. Do not remove the case or you may encounter an electric shock.
Obtain desired output level by adjusting the individual input and master volume controls. For normal: The music playing or announcement, adjust volume using their controls until the normal LED intermittently lights. Sound quality is deteriorated when the peak LED remains lit. Upon receipt of the amplifier shipment, please inspect for any damage incurred in transit. If damage is found, please notify your local representative and the transportation company immediately.
