Operating Instructions PTI-100 Version: V1.3 Doc.
About this guide ---------------------------------------------------------------------------------------- 3 1. POS Text Inserter hardware installation------------------------------------------------------- 4 1-1. Hardware Description:--------------------------------------------------------------------- 4 1-2. Specification: --------------------------------------------------------------------------------- 5 1-3.
About this guide Conventions used in this guide To make sure that you perform certain tasks properly, take note of the following symbols used throughout this manual. WARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: Information to prevent damage to the components when trying to complete a task. IMPORTANT: Information that you must follow to complete a task. NOTE: Tips and additional information to aid in completing a task.
1. POS Text Inserter hardware installation This chapter will show function, specification and configuration of POS Text Inserter system. 1-1. Hardware Description: PTI-100 EX-400USB 1: USB Cable – Connect to POS machine for POS text transmits to DVR via TCP/IP and provides the power for PTI-100 operation. 2: Serial Port (Male) – Connect to printer 3: Power Jack – Connect to DC5V power 4: RS-485 Port – Connect to EX-400USB device for POS text transmits to DVR via RS-485. 5.
1-2. Specification: Item \ Model PTI-100 Function POS text inserter EX-400USB Transaction text data Communication RS-485 full duplex up to 1.2Km using twisted pair cable Baud Rate 19200/ 9600/ 4800/ 2400 BPS Interface Series, Parallel and RS-485 Dimension Power Temperature 4 ports RS-485 interface 135 x 110 x 35 mm 120 x 100 mm DC 5V/250mA DC 5V/500mA Operation: 0-70℃, Storage: -10-80℃ (Non- Condensing) 1-3.
Baud rate 2400 4800 9600 19200 S3 ↓ ↑ ↓ ↑ S4 ↓ ↓ ↑ ↑ Switch Table 1.1 S5-S8: For ID address setting; the table of ID address show as below: Table 1.
P 3-P16: No use. EX-400USB 4 ports RS-485 Interface z RS-485: Each EX-400USB can connect 4 sets PTI-100. Y: Transmitter (+) Z: Transmitter (-) A: Receiver (+) B: Receiver (-) To avoid the interference problems, each twisted pair cable must be connected to Y&Z or A&B port. i.e. Y and A (Z and B) port can not use a twisted pair cable. 1-4.
1-5. How to configure the POS Text Inserter System? The POS text Inserter System allows you to insert text into the video clips, of up to 16 POS systems within 1.2 km by means of twisted pair cable. Using the POS text Inserter System will allow the transaction text of POS to be inserted into the video clips through I-View’s DVR. Please follow instructions below to complete hardware settings. Step 1. Check the printer type (Serial or Parallel) of POS system.
b. Plug USB cable of PTI-100 into the USB port of POS system for power; or use the DC5V power adapter into PTI-100. c. Let S2 switch (8 Pin dip switch) ↓ON. d. Using 4-wire/twisted pair cable to connect the RS-485 port between PTI-100 and EX-400USB. Please make sure the port connection must be Y to Y; Z to Z; A to A; B to B. You can ignore the driver request of POS system when you use the RS-485 text transmission. Via TCP/IP: a. Repeat the same setup as for Via RS-485 in step “a”. b.
Fig 2-1.1 z Font Click z Delete Click Fig 2-1.2 icon, you could specify the font size of POS text to past on the video clips. icon and you could delete the POS text of motor. z POS text data show on Enable/disable Monitor, Video clips and Remote to display the POS text on local monitor, video clips and/or remote PC. z Setup POS connection (Please refer to Fig 2-1.2) Enable/disable Monitor, Video clips and Remote to display the POS text on local monitor.
starts and specifies the time period of video recording once the sale stops Clear text over screen when transaction ends: This would clear/clean up the text over the screen after the specified time period when sale stops. Setup the printer command code: The DVR is able to process certain functions after receiving the printer command code, such as recording with the event of opening cash draw. OK: Click this icon to complete setting. Fig 2-1.3 Fig 2-1.4 2-2.
Fig 2-2.1 Fig 2-2.2 Step 2. Click “Setup POS connection” tab and you should see the following image as Fig2-2.2. a. Select the “Auto ” from “COM Port” tab. b. Select printer model that is to be used with POS system from “ Printer model “ tab. c. Enter IP address of DVR into “ DVR IP address “ tab. The POS transaction text will transmit to the assigned DVR. d. Select the “Auto ” from “ Insert text to camera” tab. e.
Step 3. Enable “Enable auto run system ” tab, the EZNetPOS program will be enable when you turn on the POS machine. Step 4. Click “POS insert text” tab and you search the detail information of POS insert text on each camera. You can refer to the detail description from Chapter 2-3. Step 5. Click “OK” icon to complete the setting. Step 4. Click “POS insert text” tab and you can search for detailed information of POS inserted text on each camera. You can refer to the detail description from Chapter 2-3.
Follow the steps below to play back videos: Step 1. Run EZPOSPlayback program and you will see window below. Step 2. Select the camera which you want playback. Step 3. Select the recording date and all video clips will be listed on the table. Step 4. Enable “ Use default “ icon. If you want to playback the video clips of POS transaction text via LAN, please refer to Witness software operation manual Chapter 6-10 for detailed operation. Step 5. Select video clips from video list table to playback. Step 6.
video clips containing the selected keyword in the inserted text will be listed. c. Search: Select “ Search “ tab and then enter a text that you want to check with video. The video clips containing the selected text will be listed. Step 7. For each icon function of playback, please refer to the Witness software operation manual Chapter 6-10 for detail operation.
