Owner's manual

75
4. XSEL-R/S/RX/SX/RXD/SXD
4.6 How to Handle XSEL I/O Port Numbers and PLC Addresses
In PLC, the XSEL 's CC-Link board is set as the remote device station.
The number
of occupied remote device stations varies, depending on the I/O point setting on the
XSEL side.
Shown
below is a table describing the relation between the I/O port numbers and PLC by the number
of I/O ports setting (total number of ports used for CC-Link).
(1) In the case that the I/O Point Setting is up to 96 points (No. of Occupied Stations: One Station)
16 000 to 015 RY 0 to F 300 to 315 RX 0 to F
32 016 to 031 RY 10 to 1F 316 to 331 RX 10 to 1F
48 032 to 047 RWw0 332 to 347 RWr0
64 048 to 063 RWw1 348 to 363 RWr1
80 064 to 079 RWw2 364 to 379 RWr2
96 080 to 095 RWw3 380 to 395 RWr3
Note The ports in gray column show the system domain for the remote device
station on the PLC side, so any of them can not be used as an I/O port.
[Refer to Section 4]
(2)
When the number of I/O points is set to 112 or more and 192 or less (two stations are occupied)
I/O Point
Input Port Number on
XSEL
PLC Side
Output Port Number
on XSEL
PLC Side
16 000 to 015 RY 0 to F 300 to 315 RX 0 to F
32 016 to 031 RY 10 to 1F 316 to 331 RX 10 to 1F
48 032 to 047 RY 20 to 2F 332 to 347 RX 20 to 2F
64 048 to 063 RY 30 to 3F 348 to 363 RX 30 to 3F
80 064 to 079 RWw0 364 to 379 RWr0
96 080 to 095 RWw1 380 to 395 RWr1
112 096 to 111 RWw2 396 to 411 RWr2
128 112 to 127 RWw3 412 to 427 RWr3
144 128 to 143 RWw4 428 to 443 RWr4
160 144 to 159 RWw5 444 to 459 RWr5
176 160 to 175 RWw6 460 to 475 RWr6
192 176 to 191 RWw7 476 to 491 RWr7
Note The ports in gray column show the system domain for the remote device
station on the PLC side, so any of them can not be used as an I/O port.
[Refer to Section 4]
4.6 How to Handle XSEL I/O Port Numbers and PLC Addresses
In PLC, the XSEL’s CC-Link board is set as the remote device station.
The number of occupied remote device stations varies, depending on the I/O point setting on the
XSEL side.
Shown below is a table describing the relation between the I/O port numbers and PLC by the
number of I/O ports setting (total number of ports used for CC-Link).
(1)
In the case that the I/O Point Setting is up to 96 points (one station is occupied)
I/O Point
Input Port Number on
XSEL
PLC Side
Output Port Number
on XSEL
PLC Side
16 000 to 015 RY 0 to F 300 to 315 RX 0 to F
32 016 to 031 RY 10 to 1F 316 to 331 RX 10 to 1F
48 032 to 047 RWw0 332 to 347 RWr0
64 048 to 063 RWw1 348 to 363 RWr1
80 064 to 079 RWw2 364 to 379 RWr2
96 080 to 095 RWw3 380 to 395 RWr3
Note The ports in gray column show the system area for the remote device station on
the PLC side, so any of them can not be used as an I/O port.
[Refer to Section (4)]
(2) When the number of I/O points is set to 112 or more and 192 or less (two stations are occupied)
I/O Point
Input Port Number on
XSEL
PLC Side
Output Port Number
on XSEL
PLC Side
16 000 to 015 RY 0 to F 300 to 315 RX 0 to F
32 016 to 031 RY 10 to 1F 316 to 331 RX 10 to 1F
48 032 to 047 RY 20 to 2F 332 to 347 RX 20 to 2F
64 048 to 063 RY 30 to 3F 348 to 363 RX 30 to 3F
80 064 to 079 RWw0 364 to 379 RWr0
96 080 to 095 RWw1 380 to 395 RWr1
112 096 to 111 RWw2 396 to 411 RWr2
128 112 to 127 RWw3 412 to 427 RWr3
144 128 to 143 RWw4 428 to 443 RWr4
160 144 to 159 RWw5 444 to 459 RWr5
176 160 to 175 RWw6 460 to 475 RWr6
192 176 to 191 RWw7 476 to 491 RWr7
Note The ports in gray column show the system area for the remote device station on
the PLC side, so any of them can not be used as an I/O port.
[Refer to Section (4)]