Owner's manual

76
4. XSEL-R/S/RX/SX/RXD/SXD
(3) When the number of I/O points is set to 208 or more and 256 or less (three stations are occupied)
I/O Point
Input Port Number on
XSEL
PLC Side
Output Port Number
on XSEL
PLC Side
16 000 to 015 RY 0 to F 300 to 315 RX 0 to F
32 016 to 031 RY 10 to 1F 316 to 331 RX 10 to 1F
48 032 to 047 RY 20 to 2F 332 to 347 RX 20 to 2F
64 048 to 063 RY 30 to 3F 348 to 363 RX 30 to 3F
80 064 to 079 RY 40 to 4F 364 to 379 RX 40 to 4F
96 080 to 095 RY 50 to 5F 380 to 395 RX 50 to 5F
112 096 to 111 RWw0 396 to 411 RWr0
128 112 to 127 RWw1 412 to 427 RWr1
144 128 to 143 RWw2 428 to 443 RWr2
160 144 to 159 RWw3 444 to 459 RWr3
176 160 to 175 RWw4 460 to 475 RWr4
192 176 to 191 RWw5 476 to 491 RWr5
208 192 to 207 RWw6 492 to 507 RWr6
224 208to 223 RWw7 508 to 523 RWr7
240 224 to 239 RWw8 524 to 539 RWr8
256 240 to 255 RWw9 540 to 555 RWr9
A
pp
licable 䋭 RWwA 䋭 RWrA
A
pp
licable 䋭 RWwB 䋭 RWrB
Note The ports in gray column show the system domain for the remote device
station on the PLC side, so any of them can not be used as an I/O port.
[Refer to Section 4]
In the case of three occupied stations, 12 words for each input and output are allocated
for the data register on the PLC side (10 words for XSEL). Take care of the duplicated
use of the data registers on the PLC side.
I/O Point
Input Port Number on
XSEL
PLC Side
Output Port Number
on XSEL
PLC Side
16 000 to 015 RY 0 to F 300 to 315 RX 0 to F
32 016 to 031 RY 10 to 1F 316 to 331 RX 10 to 1F
48 032 to 047 RY 20 to 2F 332 to 347 RX 20 to 2F
64 048 to 063 RY 30 to 3F 348 to 363 RX 30 to 3F
80 064 to 079 RY 40 to 4F 364 to 379 RX 40 to 4F
96 080 to 095 RY 50 to 5F 380 to 395 RX 50 to 5F
112 096 to 111 RWw0 396 to 411 RWr0
128 112 to 127 RWw1 412 to 427 RWr1
144 128 to 143 RWw2 428 to 443 RWr2
160 144 to 159 RWw3 444 to 459 RWr3
176 160 to 175 RWw4 460 to 475 RWr4
192 176 to 191 RWw5 476 to 491 RWr5
208 192 to 207 RWw6 492 to 507 RWr6
224 208 to 223 RWw7 508 to 523 RWr7
240 224 to 239 RWw8 524 to 539 RWr8
256 240 to 255 RWw9 540 to 555 RWr9
Unavailable
for Setting
─ RWwA ─ RWrA
Unavailable
for Setting
─ RWwB ─ RWrB
Note The ports in gray column show the system area for the remote device
station on the PLC side, so any of them can not be used as an I/O port.
[Refer to Section (4)]
In the case of three occupied stations, 12 words for each input and output are allocated
for the data register on the PLC side (10 words for XSEL). Take care of the duplicated
use of the data registers on the PLC side.