User Guide Type 2292, 6343, 6349, 6350 Type 6790, 6791, 6792, 6793, 6794, 6795 Type 6823, 6825
User Guide Type 2292, 6343, 6349, 6350 Type 6790, 6791, 6792, 6793, 6794, 6795 Type 6823, 6825
Note Before using this information and the product it supports, be sure to read the “Safety Information” on page v and “Appendix E. Notices and trademarks” on page 69. First Edition (August 2001) © Copyright International Business Machines Corporation 2001. All rights reserved. US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract with IBM Corp.
Contents Safety Information . . . . . . . . . . v Lithium battery notice . . . . . . . . . . . vi Modem safety information . . . . . . . . . vi Laser compliance statement . . . . . . . . . vii About this book . . . . . . . . . . . ix How this book is organized . . . . . . . . . ix Information resources . . . . . . . . . . . x Chapter 1. Overview . . . . . . . . . 1 Identifying your computer . . . . . . . . Small desktop model computer . . . . . Desktop model computer . . . . . . .
Trademarks . . . . . . . . . . . . . . 70 Index . . . . . . . . . . . . . . .
Safety Information DANGER Electrical current from power, telephone, and communication cables is hazardous. To avoid a shock hazard: v Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm. v Connect all power cords to a properly wired and grounded electrical outlet. v Connect to properly wired outlets any equipment that will be attached to this product.
réseaux, aux systèmes de té lécommunication et aux modems (sauf instruction contraire mentionnée dans les procédures d’installation et de configuration). v Lorsque vous installez, que vous déplacez, ou que vous manipulez le présent produit ou des périphériques qui lui sont raccordés, reportez-vous aux instructions ci-dessous pour connecter et déconnecter les différents cordons. Connexion: Déconnexion: 1. Mettez les unités hors tension. 1. Mettez les unités hors tension. 2.
v Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. v Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. v Use caution when installing or modifying telephone lines. v Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.
DANGER Laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. DANGER: Certains modèles d’ordinateurs personnels sont équipés d’origine d’une unité de CD-ROM ou de DVD-ROM. Mais ces unités sont également vendues séparément en tant qu’options. L’unité de CD-ROM/DVD-ROM est un appareil à laser.
About this book This publication provides instructions for installing most options into your computer. This publication also includes an overview of computer features, locating connectors, and updating configuration settings. How this book is organized This book contains the following chapters and appendixes: v “Chapter 1. Overview“ provides an introduction to the computer specifications and the options that are available for your computer. v ”Chapter 2.
Information resources The Quick Reference that comes with your computer provides information for installing your computer and starting the operating system. It also includes basic troubleshooting information, software recovery procedures, help and service information, and warranty information. Access IBM provides a link to more information about your computer. Click Start → Access IBM. If you have Internet access, the most up-to-date manuals for your computer are available from the World Wide Web.
Chapter 1. Overview Thank you for selecting an IBM® computer. Your computer incorporates many of the latest advances in computer technology and can be upgraded as your needs change. Adding hardware options to your computer is an easy way to increase its capabilities. Instructions for installing external and internal options are included in this publication. When adding an option, use these instructions along with the instructions that come with the option.
Small desktop model computer Desktop model computer Microtower model computer 2 User Guide
Features This section provides an overview of the computer features, preinstalled software, and specifications. Microprocessor Intel® Pentium™ 4 with 256 KB of internal L2 cache memory and Intel NetBurst™ micro-architecture Memory v Support for three dual in-line memory modules (DIMMs) (some models) v 512 KB flash memory for system programs Internal drives v 3.5-inch, 1.
v Front connectors for microphone and headphone (some models) Expansion v Drive bays – Small desktop model: Three – Desktop model: Four – Microtower model: Five v 32-bit peripheral component interconnect (PCI) adapter slots – Small desktop model: Three (supports low profile adapters only) – Desktop model: Three – Microtower model: Three v One accelerated graphics port (AGP) expansion slot (small desktop model supports low profile adapters) Power v 160 W or 185 W power supply with manual voltage selection sw
v PC DOS Specifications This section lists the physical specifications for your computer. Physical specifications — small desktop model Dimensions Height: 104 mm (4.1 in.) Heat output (approximate) in British thermal units (Btu) per hour: Width: 360 mm (14.2 in.) Minimum configuration: 257 Btu/hr (75 watts) Depth: 412 mm (16.2 in.) Maximum configuration: 686 Btu/hr (200 watts) Airflow Weight Minimum configuration as shipped: 8.1 kg (18 lb) Maximum configuration: 9.
Physical specifications — desktop model Dimensions Height: 140 mm (5.5 in.) Heat output (approximate) in British thermal units (Btu) per hour: Width: 425 mm (16.7 in.) Minimum configuration: 257 Btu/hr (75 watts) Depth: 425 mm (16.7 in) Maximum configuration: 789 Btu/hr (230 watts) Airflow Weight Minimum configuration as shipped: 10.0 kg (22 lb) Maximum configuration: 11.4 kg (25.
Physical specifications — microtower model Dimensions Height: 444.5 mm (17.5 in.) Heat output (approximate) in British thermal units (Btu) per hour: Width: 165.1 mm (6.5 in.) Minimum configuration: 257 Btu/hr (75 watts) Depth: 497.8 mm (19.6 in.) Maximum configuration: 789 Btu/hr (230 watts) Airflow Weight Minimum configuration as shipped: 9.1 kg (20 lb) Maximum configuration: 10.2 kg (22.
Available options The following are some available options: v External options – Parallel port devices, such as printers and external drives – Serial port devices, such as external modems and digital cameras – Audio devices, such as external speakers for the sound system – USB devices, such as printers, joysticks, and scanners – Security device, such as a Rope Clip – Monitors – IEEE 1394 devices (requires an IEEE 1394 adapter) – SCSI devices (requires a SCSI adapter) v Internal options – System memory, call
When you handle options and other computer components, take these precautions to avoid static electricity damage: v Limit your movement. Movement can cause static electricity to build up around you. v Always handle components carefully. Handle adapters and memory modules by the edges. Never touch any exposed circuitry. v Prevent others from touching components.
10 User Guide
Chapter 2. Installing external options This chapter shows the various external connectors on your computer to which you can attach external options, such as external speakers, a printer, or a scanner. For some external options, you must install additional software in addition to making the physical connection.
The following illustration shows the location of the connectors on the front of the desktop computer. 1 USB connector 2 USB connector The following illustration shows the location of the connectors on the front of the microtower computer. Note: Not all computer models will have the following connectors.
Locating the connectors on the rear of your computer The following illustration shows the location of the connectors on the rear of the small desktop model computer. See page 16 for connector descriptions.
The following illustration shows the location of the connectors on the rear of the desktop model computer. See page 16 for connector descriptions.
The following illustration shows the location of the connectors on the back of the microtower model computer. See page 16 for connector descriptions.
Connector Description Mouse connector Used to attach a mouse, trackball, or other pointing device that uses a standard mouse connector. Keyboard connector Used to attach a keyboard that uses a standard keyboard connector. USB connectors Used to attach a device that requires a Universal Serial Bus (USB) connection, such as a USB scanner or USB printer. If you have more than four USB devices, you can purchase a USB hub, which you can use to connect additional USB devices.
Chapter 3. Installing internal options — small desktop model You can expand the capabilities of your computer by adding memory, drives, or adapters. When installing an option, use these instructions along with the instructions that come with the option. Removing the cover Important Read before removing the cover “Safety Information” on page v and “Handling static-sensitive devices” on page 8. To remove the cover: 1.
Locating components The following illustration will help you locate the various components in your computer. 1 Power supply 2 PCI slot 3 AGP slot 4 Support bar 5 DIMM 6 Hard disk drive 7 CD drive or DVD drive 8 Diskette drive Identifying parts on the system board The system board, also called the planar or motherboard, is the main circuit board in your computer. It provides basic computer functions and supports a variety of devices that are IBM-installed or that you can install later.
See the following illustration for the location of parts on the system board.
2. To locate the DIMM connectors. See“Identifying parts on the system board” on page 18 . 3. Open the retaining clips. 4. Make sure the notches in the DIMM align with the tabs on the connector. Push or insert the DIMM straight down into the connector until the retaining clips close. Notches What to do next: v To work with another option, go to the appropriate section. v To complete the installation, go to “Replacing the cover and connecting the cables” on page 26.
2. Pivot one of the drive bay latch handles toward the front of the computer and then pivot the drive bay cage upward, as shown, until it is latched in the up position. Repeat this procedure for the remaining drive bay. 3. Remove the support bar by pulling it outward from the computer. Chapter 3.
4. Remove the adapter slot cover latch and the slot cover for the appropriate expansion slot. 5. Remove the adapter from its static-protective package. 6. Install the adapter into the appropriate slot on the system board. 7. Install the adapter slot cover latch. 8. Replace the support bar and pivot the two drive bays back to their original positions. What to do next: v To work with another option, go to the appropriate section.
Installing internal drives This section provides information and instructions for installing and removing internal drives. Internal drives are devices that your computer uses to read and store data. You can add or replace drives to your computer to increase storage capacity and to enable your computer to read other types of media such as CD-ROM. Internal drives are installed in bays. Within this book, the bays are referred to as bay 1, bay 2, and so on.
Installing a drive To install a CD drive or DVD drive in bay 2, follow these steps. 1. Remove the cover (see “Removing the cover” on page 17). 2. If the drive you are installing is a removable-media drive, remove the bay panel from the front bezel. 3. Remove the metal shield from the drive bay by inserting a flat–blade screwdriver into one of the slots and gently prying it loose. 4. Make sure the drive is set correctly as the master device.
To connect a CD drive or DVD drive to your computer, follow these steps. a. Locate the signal cable that came with your computer or with the new drive. b. Locate the secondary IDE connector on the system board. See “Identifying parts on the system board” on page 18. c. Connect one end of the signal cable to the secondary IDE connector on the system board and the other to the CD drive or DVD drive. d. Your computer has extra power connectors for connecting additional drives.
5. Thread the cable through the Rope Clip and around an object that is not a part of or permanently secured to the building structure or foundation, and from which it cannot be removed; then fasten the cable ends together with a lock. 1 Rope Clip 2 Bolt holes 3 Nuts What to do next: To work with another option, go to the appropriate section.
3. Position the cover over the chassis and pivot it down over the computer until it snaps into place. 4. Reconnect the external cables and power cords to the computer. See “Chapter 2. Installing external options” on page 11. 5. To update the configuration, see “Chapter 6. Using the IBM Setup Utility program” on page 55. Chapter 3.
28 User Guide
Chapter 4. Installing internal options — desktop model You can expand the capabilities of your computer by adding memory, drives, or adapters. When installing an option, use these instructions along with the instructions that come with the option. Removing the cover Important: Read “Safety Information” on page v and “Handling static-sensitive devices” on page 8 before removing the cover. To remove the cover: 1.
Locating components The following illustration will help you locate the various components in your computer. 1 2 3 4 5 6 CD-ROM drive Front USB connector Front USB connector Optional drive bay Hard disk drive Diskette drive 7 DIMMs 8 System board 9 Microprocessor and heat sink 10 AGP slot 11 PCI slots Identifying parts on the system board The system board, also called the planar or motherboard, is the main circuit board in your computer.
See the following illustration for the location of parts on the system board.
3. To locate the DIMM connectors. See “Identifying parts on the system board” on page 30 . 4. Open the retaining clips. 5. Make sure the notches in the DIMM align with the tabs on the connector. Push or insert the DIMM straight down into the connector until the retaining clips close. Notches What to do next: v To work with another option, go to the appropriate section. v To complete the installation, go to “Replacing the cover and connecting the cables” on page 38.
2. Remove the adapter slot cover latch and the slot cover for the appropriate expansion slot. 3. Remove the adapter from its static-protective package. 4. Install the adapter into the appropriate slot on the system board. 5. Install the adapter slot cover latch. What to do next: v To work with another option, go to the appropriate section. v To complete the installation, go to “Replacing the cover and connecting the cables” on page 38.
Internal drives are devices that your computer uses to read and store data. You can add drives to your computer to increase storage capacity and to enable your computer to read other types of media. Some of the different drives that are available for your computer are: v Hard disk drives v Tape drives v CD drives or DVD drives v Removable media drives Internal drives are installed in bays. Within this book, the bays are referred to as bay 1, bay 2, and so on.
Notes: 1. Drives that are greater than 41.3 mm (1.6 in.) high cannot be installed. 2. Install removable media (tape or CD) drives in the accessible bay: bay 1 or 2. Installing a drive To install an internal drive, follow these steps. 1. Remove the cover. See “Removing the cover” on page 29. 2. If your computer has a CD drive or DVD drive, you might need to remove the signal and power cables from the drive. 3.
v If it is the first CD drive or DVD drive, set as a master device. v If it is an additional CD drive or DVD drive, set as a slave device. Refer to the documentation that comes with your drive for master/slave jumper information. 7. Install the drive into the bay. Align the screw holes and insert the two screws. 8. Pivot the drive bay cage back into place. 9.
3. Connect one end of the signal cable to the drive and the other to the secondary IDE connector on the system board. To reduce electronic noise, use the connectors at the end of the cable only. 4. Your computer has extra power connectors for additional drives. Connect a power connector to the drive. 5. If you have a CD-ROM audio cable, connect it to the drive and to the system board. See “Identifying parts on the system board” on page 30. To connect an additional IDE CD drive or DVD drive 1.
5. Thread the cable through the Rope Clip and around an object that is not a part of or permanently secured to the building structure or foundation, and from which it cannot be removed; then fasten the cable ends together with a lock. 1 Rope Clip 2 Bolt holes 3 Nuts What to do next: To work with another option, go to the appropriate section.
3. Position the cover over the chassis and pivot it down over the computer until it snaps into place. 4. Reconnect the external cables and power cords to the computer. See “Chapter 2. Installing external options” on page 11. 5. To update the configuration, see “Chapter 6. Using the IBM Setup Utility program” on page 55. Chapter 4.
40 User Guide
Chapter 5. Installing internal options — microtower model You can expand the capabilities of your computer by adding memory, drives, or adapters. When installing an option, use these instructions along with the instructions that come with the option. Removing the cover Important: Read “Safety Information” on page v and “Handling static-sensitive devices” on page 8 before removing the cover. To remove the cover: 1.
Locating components The following illustration will help you locate the various components in your computer. 1 Microprocessor and heat sink 2 DIMM 3 AGP slot 4 PCI adapter 5 Power supply Moving the power supply To perform some operations inside the computer, you might need to move the power supply to access parts of the system board that are difficult to see or hard to reach. Use the following procedure to provide easier access to the system board. 1. Locate the power supply.
2. Push the plastic tab to release the power supply. 3. Move the power supply outward from the computer. 4. To replace the power supply, reverse these steps. Identifying parts on the system board The system board, also called the planar or motherboard, is the main circuit board in your computer. It provides basic computer functions and supports a variety of devices that are IBM-installed or that you can install later. Chapter 5.
See the following illustration for the location of parts on the system board.
3. To locate the DIMM connectors. See “Identifying parts on the system board” on page 43 . 4. Open the retaining clips. 5. Make sure the notches in the DIMM align with the tabs on the connector. Push or insert the DIMM straight down into the connector until the retaining clips close. Notches What to do next: v Replace any adapters that were removed. v Replace the power supply. v To work with another option, go to the appropriate section.
2. Remove the adapter slot cover latch and the slot cover for the appropriate expansion slot. 3. Remove the adapter from its static-protective package. 4. Install the adapter into the appropriate slot on the system board. 5. Install the adapter slot cover latch.
What to do next v To work with another option, go to the appropriate section. v To complete the installation, go to “Replacing the cover and connecting the cables” on page 52. Installing internal drives This section provides information and instructions for installing and removing internal drives. Internal drives are devices that your computer uses to read and store data. You can add drives to your computer to increase storage capacity and to enable your computer to read other types of media.
The following illustration shows the locations of the drive bays. The following table describes some of the drives you can install in each bay and their height requirements. 1 Bay 1 - Maximum Height: 41.3 mm (1.6 in.) CD-ROM drive (standard in some models) 5.25-inch hard disk drive 2 Bay 2 - Maximum Height: 41.3 mm (1.6 in.) 5.25-inch hard disk drive 3.5-inch hard disk drive (requires a mounting bracket) CD-ROM drive DVD-ROM drive 3 Bay 3 - Maximum Height: 25.8 mm (1.0 in.) 3.
4. Remove the metal shield from the drive bay by inserting a flat-blade screwdriver into one of the slots and gently prying it loose. 5. Make sure the drive that you are installing is set correctly as either a master or a slave device. v If it is the first CD drive or DVD drive, set as a master device. v If it is an additional CD drive or DVD drive, set as a slave device. v If it is a hard disk drive, set as a slave device.
6. Install the drive into the bay. Align the screw holes, and insert the screws that secure the drive to the bay. 7. Each integrated drive electronics (IDE) drive requires two cables; a four-wire power cable that connects to the power supply and a signal cable that connects to the system board. For a CD-ROM drive, you might also have an audio cable. The steps to connect an IDE drive are different depending on the type of drive you are connecting. Locate the procedure below for your drive connection.
5. If you have a CD-ROM audio cable, connect it to the drive and to the system board. See “Identifying parts on the system board” on page 43. To connect an additional IDE CD drive or DVD drive 1. Locate the secondary IDE connector on the system board and the three-connector signal cable. See “Identifying parts on the system board” on page 43. 2. Connect the extra connector in the signal cable to the new CD drive or DVD drive. 3. Your computer has extra power connectors for additional drives.
5. Thread the cable through the Rope Clip and around an object that is not a part of or permanently secured to the building structure or foundation, and from which it cannot be removed; then fasten the cable ends together with a lock. 1 Rope Clip 2 Bolt holes 3 Nuts What to do next: To work with another option, go to the appropriate section.
3. Position the cover on the chassis so that the rail guides on the bottom of the cover engage the rails and push the cover closed until it latches. 4. Reconnect the external cables and power cords to the computer. See “Chapter 2. Installing external options” on page 11. 5. To update the configuration, see “Chapter 6. Using the IBM Setup Utility program” on page 55. Important: When the power cord is first plugged in, the computer might appear to power on for a few seconds, then power off.
54 User Guide
Chapter 6. Using the IBM Setup Utility program The IBM Setup Utility program is stored in the electrically erasable programmable read-only memory (EEPROM) of your computer. The IBM Setup Utility program is used to view and change the configuration settings of your computer, regardless of which operating system you are using. However, the operating system settings might override any similar settings in the IBM Setup Utility program.
Administrator password Setting an administrator password deters unauthorized persons from changing configuration settings. If you are responsible for maintaining the settings of several computers, you might want to set an administrator password. After you set an administrator password, a password prompt is displayed each time you try to access the IBM Setup Utility program. If you type the wrong password, you will see an error message.
10. Move the jumper back to the standard (pins 1 and 2). 11. Replace the cover and connect the power cord. See “Replacing the cover and connecting the cables” on page 26 (small desktop model), “Replacing the cover and connecting the cables” on page 38 (desktop model), or “Replacing the cover and connecting the cables” on page 52 (microtower model). 12. When you restart the computer, a 0162 error message will be displayed. This is normal.
1. Start the IBM Setup Utility program (see “Starting the IBM Setup Utility program” on page 55). 2. Select Startup. 3. Select Startup Sequence. See the information displayed at the right side of the screen. 4. Select the sequence of devices for the Primary Startup Sequence, the Automatic Startup Sequence, and the Error Startup Sequence. 5. Select Exit from the IBM Setup Utility menu and then Save Settings.
Appendix A. Changing the battery Your computer has a special type of memory that maintains the date, time, and settings for built-in features, such as parallel-port assignments (configuration). A battery keeps this information active when you turn off the computer. The battery normally requires no charging or maintenance throughout its life; however, no battery lasts forever. If the battery fails, the date, time, and configuration information (including passwords) are lost.
Note: When the computer is turned on for the first time after battery replacement, an error message might be displayed. This is normal after replacing the battery. 9. Turn on the computer and all attached devices. 10. Use the IBM Setup Utility program to set the date and time and any passwords.
Appendix B. Updating System Programs The following contains information about updating system programs (POST/BIOS) and how to recover from a POST/BIOS update failure. System programs System programs are the basic layer of software that is built into your computer. They include the power-on self-test (POST), the basic input/output system (BIOS) code, and the IBM Setup Utility program. POST is a set of tests and procedures that is performed each time you turn on your computer.
6. Replace the cover. See “Replacing the cover and connecting the cables” on page 26 (small desktop model), “Replacing the cover and connecting the cables” on page 38 (desktop model), or “Replacing the cover and connecting the cables” on page 52 (microtower model). 7. Reconnect the power cords for the computer and monitor to electrical outlets. 8. Insert the POST/BIOS update (flash) diskette into drive A, and turn on the computer and the monitor. 9.
Appendix C. System address maps The following charts represent how the hard disk stores different types of information. Address ranges and byte sizes are approximate. System memory map The first 640 KB of system board RAM is mapped starting at address hex 00000000. A 256-byte area and a 1 KB area of this RAM are reserved for BIOS data. Memory can be mapped differently if POST detects an error. Table 1.
Table 2.
Table 2.
Table 3.
Appendix D. Interrupt request and direct memory access channel assignments The following tables list the IRQ and DMA channel assignments. Table 4.
68 User Guide
Appendix E. Notices and trademarks This publication was developed for products and services offered in the U.S.A. IBM may not offer the products, services, or features discussed in this document in other countries. Consult your local IBM representative for information on the products and services currently available in your area. Any reference to an IBM product, program, or service is not intended to state or imply that only that IBM product, program, or service may be used.
intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited. Trademarks The following terms are trademarks of the IBM Corporation in the United States or other countries or both: IBM Wake on LAN PS/2 Pentium and NetBurst are trademarks of Intel Corporation in the United States, other countries, or both.
Index A E adapters accelerated graphics port (AGP) 8 installing desktop model 32 microtower model 45 small desktop model 20 peripheral component interconnect (PCI) slots 20, 32, 45 address map DMA input/output (I/O) 65 input/output (I/O) 63 system memory 63 audio, subsystem 3 audio line in connector 13, 14, 15, 16 audio line out connector 13, 14, 15, 16 environment, operating 5, 6, 7 Ethernet connector 13, 14, 15, 16 C cables, connecting 26, 38, 52 changing the battery 59 channel assignments DMA 67 IRQ
O options available 8 external 8, 11 installing desktop model 29 microtower model 41 small desktop model 17 internal 8, 17, 29, 41 P parallel connector 13, 14, 15, 16 password erasing 56 lost or forgotten 56 setting, changing, deleting 56 power Advanced Configuration and Power Interface (ACPI) support 4 Advanced Power Management support 4 R recovering from a POST/BIOS update failure 61 removing the cover desktop model 29 microtower model 41 small desktop model 17 replacing the cover desktop model 38 micro
Part Number: 25P4024 Printed in the United States of America on recycled paper containing 10% recovered post-consumer fiber.