IBM® xSeries 220 IBM User’s Reference SC06-P460-70
First Edition (October 2000) © Copyright International Business Machines Corporation 2000. All rights reserved. US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract with IBM Corp.
Contents Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v Chapter 1.Introducing the IBM xSeries 2201 Features and specifications . . . . . . . . . . . . . . . . . . . . . . . . Notices used in this book . . . . . . . . . . . . . . . . . . . . . . . . . . What your xSeries 220 offers . . . . . . . . . . . . . . . . . . . . . . . Reliability, availability, and serviceability features . . . . Server controls and indicators. . . . . . . . . . . . . . . . . . . . . . Turning on the server . . .
Novell NetWare or IntraNetWare server ODI driver teaming messages . . . . . . . . . . . . . . . . . . . . . . . . . 108 NDIS 4.0 (Windows NT) driver messages . . . . 109 Replacing the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 Getting help, service, and information. . . . . . . . . . . . . 115 Getting information . . . . . . . . . . . . . . . . . . . . . . . . . . 115 Using the World Wide Web . . . . . . . . . . . . . . . . . 115 Getting information by fax . . . . . . . . . . . . . .
Safety Before installing this product, read the Safety Information book. Antes de instalar este produto, leia o Manual de Informações sobre Segurança. Pred instalací tohoto produktu si prectete prírucku bezpecnostních instrukcí. Læs hæftet med sikkerhedsforskrifter, før du installerer dette produkt. Lue Safety Information -kirjanen, ennen kuin asennat tämän tuotteen. Avant de procéder à l'installation de ce produit, lisez le manuel Safety Information.
Lees voordat u dit product installeert eerst het boekje met veiligheidsvoorschriften. Les heftet om sikkerhetsinformasjon (Safety Information) før du installerer dette produktet. Antes de instalar este produto, leia o folheto Informações sobre Segurança. Перед установкой продукта прочтите брошюру по технике безопасности (Safety Information). Pred inštaláciou tohto produktu si pre ítajte Informa nú brožúrku o bezpe nosti. Preden namestite ta izdelek, preberite knjižico Varnostne informacije.
Statement 1 Danger Electrical current from power, telephone, and communication cables is hazardous. To avoid a shock hazard: • Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm. • Connect all power cords to a properly wired and grounded electrical outlet. • Connect to properly wired outlets any equipment that will be attached to this product.
Statement 2 CAUTION: When replacing the lithium battery, use only IBM Part Number 33F8354 or an equivalent type battery recommended by the manufacturer. If your system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of. Do not: • Throw or immerse into water.
Statement 4 ≥18 kg (39.7 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs) CAUTION: Use safe practices when lifting. Statement 5 CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source.
x IBM® xSeries 220 User’s Reference
Chapter 1. Introducing the IBM xSeries 220 Your IBM® xSeries 220 delivers great value for entry server applications. It is ideally suited for networking environments that require superior microprocessor performance, efficient memory management, flexibility, and large amounts of reliable data storage. Your IBM xSeries 220 server comes with a three-year limited warranty and IBM Server Start Up Support.
Features and specifications Table 1 provides a summary of the features and specifications of your xSeries 220 server. Microprocessor: Video: Environment: • Intel® Pentium® III microprocessor with MMX™ technology and SIMD extensions • S3 video controller (integrated on system board) • • Compatible with SVGA and VGA • 256 KB* ECC, level-2 cache (min.) • 8 MB SDRAM video memory • 133 MHz front-side bus (FSB) Size: • Support for up to two microprocessors • Height: 470 mm (18.5 in.
Notices used in this book The caution and danger notices also appear in the multilingual Safety Information book provided on the IBM xSeries Documentation CD that comes with your xSeries product. Each notice is numbered for easy reference to the corresponding notices in the safety book. The following types of notices are used in this book: • Note: These notices provide important tips, guidance, or advice.
• IBM ServerGuide™ CDs The ServerGuide CDs that are included with your server provide programs to help you set up your server and install the network operating system (NOS). The ServerGuide program detects the hardware options that are installed and provides the correct configuration programs and device drivers. In addition, the ServerGuide CDs include a variety of application programs for your server. For more information about the ServerGuide CDs, see “Chapter 4. Using the ServerGuide CDs,” on page 21.
Server controls and indicators This section identifies the controls and indicators on the front of your server. CD-ROM eject button CD-ROM drive activity light Diskette-eject button Diskette drive activity light SCSI activity light Power-on light Power-control button System error light CD-ROM eject button: Press this button to release a CD from the drive. CD-ROM drive activity light: When this light is on, it indicates that the CD-ROM drive is in use.
Cover-release latch: Slide this lever to release the cover. Key lock:Use the key that comes with your server to unlock the cover.
Turning on the server Turning on the server refers to the act of plugging the power cord of your server into the power source and starting the operating system. After you plug the power cord of your server into the power supply and an electrical outlet, the server can start in any of the following ways: • You can press the power-control button on the front of the server to start the server. Notes: 1. You can install a circular disk over the power-control button to prevent accidental manual power-off.
Turning off the server Turning off the server refers to the act of disconnecting the server from the power source. You can turn off the server in any of the following ways: Statement 5 CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source.
Chapter 2. Arranging your workspace To get the most from your server, arrange both the equipment you use and your work area to suit your needs and the kind of work you do. Your comfort is of foremost importance, but light sources, air circulation, and the location of electrical outlets also can affect the way you arrange your workspace. Comfort Although no single working position is ideal for everyone, here are a few guidelines to help you find a position that suits you best.
Place the server and monitor so that nothing blocks the air vents; usually, 15 cm (6 inches) of air space is sufficient. Also, make sure that the vented air is not blowing on someone else. Electrical outlets and cable lengths The location of electrical outlets and the length of power cords and cables that connect to the monitor, printer, and other devices might determine the final placement of your server. When arranging your workspace: • Avoid the use of extension cords.
Chapter 3. Configuring your server The following configuration programs are provided with your server: • Configuration/Setup Utility This program is part of the basic input/output system (BIOS) code that comes with your server. You can use this program to configure serial and parallel port assignments, change interrupt request (IRQ) settings, change the drive startup sequence, set the date and time, and set passwords. See “Using the Configuration/Setup Utility program” for more information.
Notes: a. You can set an administrator password through the Configuration/Setup Utility program only if the optional system-management adapter is installed in your server. b. If you have set both levels of passwords (user and administrator), you must type the administrator password to access the full Configuration/Setup Utility menu. 3. Follow the instructions that appear on the screen.
Configuration/Setup Utility main menu. — Product Data Select this choice to view system information, such as the machine type and model, the server serial number, and the revision level or issue date of the BIOS that is stored in the flash electrically erasable programmable ROM (EEPROM). • Devices and I/O Ports Select this choice to view or change the assignments for devices and input/output ports. This choice appears only on the full Configuration/Setup Utility main menu.
defaults can only be loaded from the Configuration/Setup Utility main menu. You can enable a virus-detection test that checks for changes in the master boot record at startup. You also can select to run POST in the enhanced mode or the quick mode. • Advanced Setup Select this choice to change values for advanced hardware features, such as cache control and PCI configuration.
configuration information. This usually results in automatic configuration of a PCI device. Attention: You must use the menu selections to save custom settings for the PCI Slot/Device Information choice. The Save Settings, Restore Settings, and Load Default Settings choices on the main menu of the Configuration/Setup Utility do not save the PCI Slot/Device Information settings. After making changes, select: • – Save and exit the PCI Utility to save the changes and return to the Advanced Setup choice.
• Remove the battery and then reinstall the battery. Setting the password-override switch: The following illustration shows the location of the password-override switch (switch 8, which is the switch farthest to the right, on switch block 1) on the system board. Power-on password-override switch (switch 8 of switch block 1) To set the password-override switch, do the following: 1. Review the information in “Before you begin” on page 31. 2.
Type of password Power-on password Administrator password Administrator and power-on password Results • Enter the password to complete the system startup. • All choices are available on the Configuration/Setup Utility main menu. • No password is required to start the system. • Enter the password to access the Configuration/Setup Utility program. • All choices are available on the Configuration/Setup Utility main menu. • You can enter either password to complete the system startup.
5. Follow the instructions on the screen to change the settings of the selected items; then, press Enter. Choices available from the SCSISelect menu The following choices appear on the SCSISelect Utility menu: • Configure/View Host Adapter Settings Select this choice to view or change the SCSI controller settings. To reset the SCSI controller to its default values, press F6; then, follow the on-screen instructions.
Using the PXE Boot Agent Utility program The Preboot eXecution Environment (PXE) Boot Agent is a built-in, menu-driven configuration utility program that you can use to: • Change network startup (boot) protocols • Change network startup (boot) order • Set menu wait times • Select operating system wake up support Starting the PXE Boot Agent Utility program The following sections provide the instructions needed to start the PXE Boot Agent Utility and descriptions of the available menu choices.
• Setup time wait menu Select this choice to set the amount of time (in seconds) that the system will pause during initialization for a Ctrl+S input. — 2 seconds (default) — 3 seconds — 5 seconds — 8 seconds • Legacy OS wake up support Select this choice to allow/disallow a non-windows operating system to use adapter remote wake up capability.
Chapter 4. Using the ServerGuide CDs The ServerGuide CDs include easy-to-use software setup and installation tools that are specifically designed for your IBM server. The ServerGuide Setup and Installation program detects the server model and hardware options that are installed and uses that information during setup to configure the hardware. The ServerGuide tools simplify NOS installations by providing updated device drivers, and in some cases, installing them automatically.
Setup and Installation CD Note: The ServerGuide program requires a supported IBM server with an enabled startable (bootable) CDROM drive. Not all features are supported on all models. • Sets system date and time. • Detects the ServeRAID adapter or controller and runs the ServeRAID configuration program. • Updates the licensed internal code (firmware) level without creating diskettes. • Checks the system BIOS level to determine whether a later level is available from the CD.
• ServerGuide displays choices for running the configuration programs. For example: — The Express Configuration method runs the required programs for your server, based on the hardware that is detected. — The Custom Configuration method displays all programs that are available for your server, and you decide which programs to run. — The Replicated Configuration method provides the option of duplicating your setup selections to other servers that are the same xSeries 220 model.
Note: Exact features and functions can vary with different versions of the ServerGuide software. • After you have completed the setup process, the operating system installation program starts. (You will need your copy of the NOS CD to complete the installation.) • ServerGuide stores information about the server model, service processor, hard disk controllers, and network adapters. It then checks the CD for newer device drivers. This information is stored and then passed to the NOS installation program.
Additional programs included with ServerGuide As a convenience, ServerGuide comes with additional software to assist you with the server installation. A variety of powerful applications are included with ServerGuide. Offerings can vary with the different versions of the ServerGuide software. Check the application CD labels for a list of applications, or start the Setup and Installation CD and view the online Overview. Error symptoms This section provides ServerGuide error symptoms and probable solutions.
26 IBM® xSeries 220 User’s Reference
Chapter 5. Installing options This chapter provides instructions to help you add options to your server. Some option-removal instructions are provided, in case you need to remove one option to install another. For a list of supported options for your server, see the ServerProven list at: http://www.ibm.com/pc/compat/ Major components of the xSeries 220 server Note: The illustrations in this document might differ slightly from your hardware.
System board The illustrations in the following sections show the components on the system board. System-board option connectors The following illustration identifies system-board connectors for user-installable options. Microprocessor 2 (U11) Microprocessor 1 (U12) Voltage regulator module (VRM) 2 (J12) Voltage regulator module (VRM) 1 (J42) DIMM 1 (J19) DIMM 2 (J21) DIMM 3 (J23) DIMM 4 (J26) PCI 1 (J29) PCI 2 (J31) Battery (BH1) PCI 5 (J40) PCI 4 (J39) System management (J32) PCI 3 (J35) Notes: 1.
System-board internal cable connectors The following illustration identifies system-board connectors for internal cables. Microprocessor fan 2 (J2) Microprocessor fan 1 (J3) Fan 2 power (J18) Main power (J1) Diskette drive (J27) DASD I2C (J43) Fan 1 power (J10) IDE (J30) Fan 3 power (J22) (not used) Wake on LAN (J20) SCSI channel (J41) System-board external port connectors The following illustration identifies the external port connectors on the rear of the server.
System-board jumpers and switches The following illustration identifies the jumpers and switches on the system board. Switch block Flash ROM page-swap jumper (J38) System-board jumper blocks Any jumper blocks on the system board that are not shown in the illustration are reserved. For normal operation of the system, no jumpers should be installed on any of the jumper blocks. See “Recovering the BIOS code” on page 97 for information about the flash ROM page-swap jumper.
Before you begin Before you begin to install options in your server, read the following information: • Become familiar with the safety and handling guidelines under “Handling static-sensitive devices”, and read the safety statements in “Safety information” on page 32. These guidelines will help you work safely while working with your server or options.
Safety information Before installing this product, read the Safety Information book. Antes de instalar este produto, leia o Manual de Informações sobre Segurança. Pred instalací tohoto produktu si prectete prírucku bezpecnostních instrukcí. Læs hæftet med sikkerhedsforskrifter, før du installerer dette produkt. Lue Safety Information -kirjanen, ennen kuin asennat tämän tuotteen. Avant de procéder à l'installation de ce produit, lisez le manuel Safety Information.
Les heftet om sikkerhetsinformasjon (Safety Information) før du installerer dette produktet. Antes de instalar este produto, leia o folheto Informações sobre Segurança. Перед установкой продукта прочтите брошюру по технике безопасности (Safety Information). Pred inštaláciou tohto produktu si pre ítajte Informa nú brožúrku o bezpe nosti. Preden namestite ta izdelek, preberite knjižico Varnostne informacije. Antes de instalar este producto, lea la Información de Seguridad.
Statement 1 Danger Electrical current from power, telephone, and communication cables is hazardous. To avoid a shock hazard: • Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm. • Connect all power cords to a properly wired and grounded electrical outlet. • Connect to properly wired outlets any equipment that will be attached to this product.
Statement 2 CAUTION: When replacing the lithium battery, use only IBM Part Number 33F8354 or an equivalent type battery recommended by the manufacturer. If your system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of. Do not: • Throw or immerse into water.
Statement 4 ≥18 kg (39.7 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs) CAUTION: Use safe practices when lifting. Statement 5 CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source.
Rotating the stabilizing feet The feet attached to the bottom cover rotate 90 degrees to provide additional stability for your server. Place the server in an upright position; then, rotate the feet a quarter turn away from the server. Carefully position the server on its feet. When you need to access the inside of the server to install options, you might find it easier to place the server on its side, so that the system board is facing you.
Removing the side cover The following information describes how to remove the side cover. Note: The illustrations in this document might differ slightly from your hardware. Cover-release latch Key lock To remove the side cover from the server, do the following: 1. Review the information in “Before you begin” on page 31. 2. Turn off the server and all attached devices, and disconnect all external cables and power cords. 3. If necessary, unlock the server cover. 4.
Removing the support bracket assembly When working with some options such as hard disk drives and microprocessors, you must first remove the support bracket assembly to access the location of the option. The support bracket assembly consists of a support bracket, an air baffle, and a fan. To remove the support bracket assembly, do the following: 1. Review the safety precautions in “Safety information” on page 32. 2.
8. Store the support bracket assembly in a safe place. Working with adapters You can install up to five peripheral component interconnect (PCI) adapters in the PCI slots on the system board of your server. See the xSeries 220 ServerProven list at http://www.ibm.com/pc/compat/ for a list of PCI adapters that your server supports. Your server comes with an integrated video controller on the system board.
The system scans PCI slots 1 through 5 to assign system resources; then, the system starts (boots) the PCI devices in the following order: PCI slots 1 and 2, system board SCSI devices, and then PCI slots 3 through 5. • If you plan to use the Wake on LAN (WOL) function in the server, you must install a Wake on LAN-enabled NIC adapter in PCI slot 1, and install the Wake on LAN cable that comes with the Wake on LAN adapter to connect this adapter to the system board.
3. Carefully remove the support bracket assembly from the server (see “Removing the support bracket assembly” on page 39). Store the cover and the support bracket assembly in a safe place. 4. Determine which PCI slot you will use for the adapter. Note: Check the instructions that come with the adapter for any requirements or restrictions. 5. Remove the rear adapter retaining bracket from the server.
12. Connect any needed cables to the adapter. Attention: Route cables so that they do not block the flow of air from the fans. The following illustration shows how to reroute the SCSI cable. If you install a ServeRAID adapter and intend to use it with hot-swap hard disk drives, remove the cable from the internal SCSI connector (J41) on the system board and connect it to the ServeRAID adapter.
Installing internal drives Different types of drives enable your system to read multiple types of media and store more data. Several types of drives are available, such as: • • • • Diskette (preinstalled) Hard disk (preinstalled on some models) CD-ROM (preinstalled) Tape Internal drive bays Internal drives are installed in bays. The bays of the xSeries 220 are in the front of the server, as shown in the following illustration.
drives. Refer to the documentation that comes with your server for additional information. Your server supports four 1-inch (26 mm) slim, 3.5-inch SCSI hard disk drives in the hard disk drive bays (4, 5, 6, and 7). You can install four non-hot-swap hard disk drives in the models that have the standard non-hot-swap drive cage. You can install three hot-swap hard disk drives and one non-hot-swap hard disk drive in the models that come with the hot-swap drive cage.
Installing a drive in bay 1, 2, 3, or 4 EMC shield Filler panel To install a drive in bay 1, 2, 3, or 4, do the following: 1. Read the information in “Preinstallation steps (all bays)” on page 45. 2. Turn off the server and peripheral devices; then, remove the side cover (see “Removing the side cover” on page 38 for details). 3. Insert a screwdriver into the slot on the right side of the filler panel, and remove the filler panel from the server. 4.
5. If the drive is a laser product, observe the following safety precaution. Statement 3 CAUTION: When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are installed, note the following: • Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device.
Installing a non-hot-swap hard disk drive in bay 5, 6, or 7 To install a non-hot-swap hard disk drive in bay 5, 6, or 7, do the following: 1. Read the information in “Preinstallation steps (all bays)” on page 45. 2. Turn off the server and peripheral devices, and disconnect all external cables and power cords; then, remove the side cover (see “Removing the side cover” on page 38 for details). 3. Remove the support bracket assembly (see “Removing the support bracket assembly” on page 39). 4.
9. If you have other options to install or remove, do so now; otherwise, replace the support bracket assembly; then, go to “Installing the side cover” on page 60. Note: If your server is a hot-swap model, reinstall the VRM in connector J42 after you reinstall the support bracket assembly. (See “System-board option connectors” on page 28 for connector location.
Note: The hard disk drive activity light and hard disk drive status light on the backplane match the hard disk drive activity light and hard disk drive status light on the hot-swap drive. The following illustration shows the rear connectors on the hot-swap-drive backplane, as viewed from the rear of the server. SCSI cable connector SCSI power cable connector 2 I C cable connector The following illustration shows how to install a hot-swap hard disk drive in the server.
Note: You do not have to turn off the server to install hot-swap hard disk drives in these bays. 3. Remove the filler panel from one of the empty hot-swap bays by inserting your finger into the depression at the left side of the filler panel and pulling it away from the server. 4. Install the hard disk drive in the hot-swap bay: a. Ensure that the tray handle is open (that is, perpendicular to the drive). b. Align the drive tray assembly with the guide rails in the bay. c.
DIMM 1 DIMM connector 1 DIMM 2 DIMM connector 2 DIMM connector 3 DIMM connector 4 Attention: When you handle electrostatic discharge (ESD) sensitive devices, take precautions to avoid damage from static electricity. For details on handling these devices, see “Handling static-sensitive devices” on page 31. To install a DIMM, do the following: 1. Review the safety precautions in Statement 1 and Statement 5 in “Safety information” on page 32. 2.
• If you installed additional memory, start the Configuration /Setup Utility program and select Save Settings. • If you just replaced a failed DIMM, you must start the Configuration /Setup Utility program, select Advanced Setup, select Memory Settings, highlight the connector or bank of connectors that you want to enable, then select Enable. • In some memory configurations, the 3-3-3 beep code might sound during POST followed by a blank screen.
Installing and removing a microprocessor Your server comes with one microprocessor, which is installed on the system board. If you install an additional microprocessor kit, your server can operate as a symmetric multiprocessing (SMP) server. With SMP, certain operating systems and application programs can distribute the processing load between the microprocessors. This enhances performance for database and point-of-sale applications, integrated manufacturing solutions, and other applications. Notes: 1.
bracket assembly in a safe place. 4. Lift the release lever and remove the terminator card from the microprocessor connector. 5. Install the microprocessor: a. Touch the static-protective package containing the new microprocessor to any unpainted metal surface on the server; then, remove the microprocessor from the package. b. Orient the microprocessor over the microprocessor connector, as shown in the following illustration. Carefully press the microprocessor into the connector.
8. If you are installing a microprocessor that has a speed lower than 933 MHz, install the heat sink onto the microprocessor: VRM 2 (J12) Terminator card Microprocessor 1 Microprocessor 2 VRM 1 (J42) Heat sink Heat-sink retainer a. Peel the plastic protective strip off the bottom of the heat sink. Make sure that the square of thermal material is still on the bottom of the heat sink. b. Align and place the heat sink on top of the microprocessor. c.
9. If you are installing a microprocessor that has a speed of 933 MHz or higher, install a fan sink onto the microprocessor and connect the fan-sink power cable to the system board: VRM 2 (J12) Terminator card Microprocessor fan 1 (J2) Microprocessor fan 2 (J3 ) Microprocessor VRM 1 (J42) Fan sink Fan-sink retainer a. Peel the plastic protective strip off the bottom of the fan sink. Make sure that the square of thermal material is still on the bottom of the fan sink. b.
(2) If you installed the microprocessor in connector U12, press down on the latches on either side of connector J42, and install the VRM in connector J42. Note: If your server is a hot-swap model, reinstall the VRM in connector J42 after you reinstall the support bracket assembly. b. Make sure that the VRM is oriented and aligned correctly. c. Press the VRM into the connector.
d. Disconnect the fan-sink power cable from the appropriate connector on the system board: • If you are removing the microprocessor from connector U11, disconnect the fan-sink power cable from connector J2. • If you are removing the microprocessor from connector U12, disconnect the fan-sink power cable from connector J3. 7. Lift up the release lever and remove the microprocessor from the connector. Store the microprocessor in a static-protective bag for possible future use. 8.
Installing the side cover The following information describes the cover installation procedure. Note: The illustrations in this document might differ slightly from your hardware. Cover-release latch Key lock Note: If you removed the support bracket assembly after you removed the cover, reinstall it before you install the cover. To install the server side cover: 1. Clear any cables that might impede the replacement of the cover. 2.
Connecting external options You can attach a SCSI storage expansion enclosure to your server if you install an optional SCSI adapter in one of the five PCI adapter slots on the system board. Installation procedure To attach an external device, do the following: 1. Read “Before you begin” on page 31 and the documentation that comes with your options. 2. Be sure that your server and all attached devices are turned off. 3.
Input/output ports This section provides information about the input/output (I/O) ports on your server. These ports include the following: • One parallel port • One video port • One keyboard port • One auxiliary pointing-device (mouse) port • Two serial ports • Two Universal Serial Bus (USB) ports • One SCSI connector • One Ethernet port • One communication connector dedicated to the system-management adapter Notes: 1.
Parallel port connector The following table shows the pin-number assignments for the 25-pin, female D-shell parallel-port connector on the rear of the server.
Configuration/Setup Utility program to change serial port address assignments to prevent or resolve address conflicts. Viewing or changing the serial-port assignments To view or change the serial-port assignments, do the following: 1. Restart the server and watch the monitor screen. 2. When the message Press F1 for Configuration/Setup appears, press F1. 3. From the main menu, select Devices and I/O Ports; then, press Enter. 4.
USB technology provides up to 12 megabits-per-second (Mbps) speed with a maximum of 127 external devices and a maximum signal distance of five meters (16 ft) per segment. USB-port connectors Each USB port has an external connector on the rear of the server for attaching USBcompatible devices. The following table shows the pin-number assignments for the USB-port connectors on the rear of the server. Pin Signal 1 +5 V dc 2 -Data 3 +Data 4 Ground Table 6.
The following table shows the pin-number assignments for the auxiliary-device connector on the rear of the server. 6 5 4 3 2 Pin 1 Signal 1 Data 2 Reserved 3 Ground 4 +5 V dc 5 Clock 6 Reserved Table 8. Auxiliary-device connector pin-number assignments Video port Your server comes with an integrated super video graphics array (SVGA) video controller. This controller is not removable, but you can disable it by installing a PCI video adapter.
SCSI port Your server has an integrated small computer system interface (SCSI) controller with an internal connector (J41) on the system board. This controller supports an Ultra160 SCSI internal channel. This channel supports up to 15 SCSI devices.
SCSI connector pin-number assignments The following table shows the pin-number assignments for the 68-pin SCSI connector.
Pin Signal Pin Signal 31 +Data 8 65 -Data 8 32 +Data 9 66 -Data9 33 +Data 10 67 -Data 10 34 +Data 11 68 -Data 11 Table 10. 68-pin SCSI connector pin-number assignments Ethernet port Your server comes with an integrated Ethernet controller. This controller provides an interface for connecting to 10-Mbps or 100-Mbps networks and provides full-duplex (FDX) capability, which enables simultaneous transmission and reception of data on the Ethernet local area network (LAN).
Teaming Mode: Your Ethernet controller provides options, called teaming options. These options increase throughput and fault tolerance when running with Windows NT 4.0 or NetWare 4.1x or later. • Adapter fault tolerance (AFT) provides automatic redundancy for your adapter. If the primary adapter fails, the secondary adapter takes over. Adapter fault tolerance supports from two to four adapters per team.
The requirements for effectively using IEEE 802.1p tagging are: • The other devices receiving and routing 802.1p tagged packets must support 802.1p. • The adapters on these devices must support 802.1p. The Ethernet controller in your xSeries 220 and all IBM Netfinity10/100 Ethernet Security Adapters support 802.1p. • The adapter cannot be assigned to an adapter team. • If you are setting up VLANs and packet tagging on the same adapter, 802.1p/802.1Q tagging must be enabled on the IBMSet Advanced tab.
To join a VLAN from Windows NT 4.0: 1. Create a VLAN on the switch. Use the parameters that you assign there to join the VLAN from the server. Refer to your switch documentation for more information. 2. In the Control Panel window, double-click the Network icon. 3. On the Adapters tab, select the adapter that you want to be on the VLAN, and click Properties. 4. In IBMSet, click Join VLAN. Note that VLANs cannot be assigned to adapters that are already defined to have an adapter teaming option. 5.
Chapter 6. Solving problems This section provides basic troubleshooting information to help you resolve some common problems that might occur with your server. If you cannot locate and correct the problem using the information in this section, refer to “Getting help, service, and information” on page 115 for more information.
Server Support Server working properly? Yes Register and profile your server After you register and profile, you will be able to: • Diagnose problems using the IBM Online Assistant • Participate in the IBM discussion forum • Receive e-mail notifications of technical updates related to your profiled products No Check all cables for loose connections and verify that all optional devices you installed are on the Server Proven list. You can view the Server Proven list at: Register at: http://www.ibm.
POST When you turn on the server, it performs a series of tests to check the operation of server components and some of the options installed in the server. This series of tests is called the power-on self-test, or POST. If POST finishes without detecting any problems, a single beep sounds, and the first window of your operating system or application program appears. If POST detects a problem, more than one beep sounds, and an error message appears on your screen.
Repeating short beeps The system board might contain a failing component, your keyboard might be defective, or a key on the keyboard might be stuck. Ensure that: 1. Nothing is resting on the keyboard and pressing a key. 2. No key is stuck. 3. The keyboard cable is connected correctly to the keyboard and to the correct connector on the server. Running the diagnostic tests can isolate the server component that failed, but you must have your system serviced. If the error message remains, call for service.
POST beep codes Beep code Description Action 1-1-2 Microprocessor register test has failed. 1-1-3 CMOS write/read test has failed. 1-1-4 BIOS ROM checksum has failed. 1-2-1 Programmable Interval Timer test has failed. 1-2-2 DMA initialization has failed. 1-2-3 DMA page register write/read test has failed. 1-4-3 Interrupt vector loading test has failed. 2-1-1 Secondary DMA register test has failed. 2-1-2 Primary DMA register test has failed.
1-2-4 RAM refresh verification has failed. 1-3-1 First 64 Kb RAM test has failed. 1-3-2 First 64 Kb RAM parity test has failed. 3-3-1 A memory size mismatch has occurred. 3-3-3 No memory has been detected in the system. Reseat the memory modules or install a memory module. If the problem persists, call for service. Attention: In some memory configurations, the 3-3-3 beep code might sound during POST followed by a blank screen.
POST error messages The following tables provide information about the POST error messages that can appear during startup. POST message 062 Description The server failed to boot on three consecutive attempts. All caches are disabled. Repeatedly turning the server on and then off or resetting the server might cause this problem. Action: Start the Configuration/Setup Utility program and verify that all settings are correct.
POST message 162 Description A change in device configuration occurred. This error occurs under one or more of the following conditions: • A new device has been installed. • A device has been moved to a different location or cable connection. • A device has been removed or disconnected from a cable. • A device is failing and is no longer recognized by the server as being installed. • An external device is not turned on. • An invalid checksum is detected in the battery-backed memory.
POST message 186 Description A system board or hardware error occurred. Call for service. Action: 187 The VPD serial number is not set. The system serial number is set in the VPD EEPROM at the time of manufacturing. If the system board has been replaced, the system serial number will be invalid and should be set. From the main menu of the Configuration/Setup Utility program, select System Information, then select Product Data.If the problem persists, call for service.
POST message 602 Description Invalid diskette boot record. 1. Replace the diskette. Action: 2. If the problem persists, make sure that the diskette drive cables are correctly and securely connected. 3. If the problem remains, replace the diskette drive. If the problem persists, call for service. 604 An error occurred during a diskette drive test. 1. Verify that the Configuration/Setup Utility program correctly reflects the type of diskette drive that you have installed. Action: 2.
POST message 1962 Description No valid startup devices were found. The system cannot find the startup drive or operating system. Be sure that the drive you want to start from is in the startup sequence. Action: 1. Select Start Options from the Configuration/Setup Utility program main menu. If you are unable to set the startup sequence, call for service. 2. Check the list of startup devices in the Startup device data fields.
POST message 00012000 Description Processor machine check. 1. Update the system BIOS. Action: 2. If the problem persists, replace the microprocessor. 00019501 Processor 1 is not functioning. Action: Replace microprocessor 1. If the problem persists, call for service. 00019502 Processor 2 is not functioning. Action: Replace microprocessor 2. If the problem persists, call for service. 00019701 Processor 1 failed the built-in self-test. Action: Replace microprocessor 1.
POST message 00180500 Description A PCI adapter ROM error occurred. Action: Remove the PCI adapters. If you can start the server without the adapters, reinstall each adapter one at a time and retest after each is reinstalled. When an adapter fails, replace it. If you cannot isolate and correct the problem, call for service. 00180600 A PCI-to-PCI bridge error occurred. More than one PCI bus tried to access memory below 1 MB. Action: Remove the PCI adapter that has the PCI bridge.
POST message Description POST could not find an operating system. I9990305 Install an operating system. If you have already installed the operating system, check the drive startup sequence. If the drive sequence is correct, run the diagnostic tests to verify that the hard disk drive is functioning correctly. If there is a problem with the hard disk drive (such as a bad sector), you might need to reinstall the operating system. Action: If you cannot reinstall the operating system, call for service.
Table 14. SCSI messages SCSI Messages All Description One or more of the following might be causing the problem. • A failing SCSI device (adapter, drive, controller) • An improper SCSI configuration • Duplicate SCSI IDs in the same SCSI chain • An improperly installed SCSI terminator • A defective SCSI terminator • An improperly installed cable • A defective cable Action: Verify that: • The external SCSI devices are turned on. External SCSI devices must be turned on before the server.
iii is the three-digit device ID. (These codes are for trained service personnel and are described in the Hardware Maintenance Manual.) date is the date that the diagnostic test was run and the error was recorded. cc is the check digit that is used to verify the validity of the information. text message is the diagnostic message that indicates the reason for the problem.
5. When the Diagnostic Programs screen appears, select the test you want to run from the list that appears; then, follow the instructions on the screen. Notes: a. If the server stops during testing and you cannot continue, restart the server and try running the diagnostic programs again. If the problem persists, call for service. b. The keyboard and mouse (pointing device) tests assume that a keyboard and mouse are attached to the server. c.
Diagnostic error message tables The following tables provide descriptions of the error messages that might appear when you run the diagnostic programs. Attention: If diagnostic error messages appear that are not listed in the following tables, make sure that your server has the latest levels of BIOS, ServeRAID, and diagnostics microcode installed. Code 001 Function Core system Result Failed Text message Processor board, ECC Test Action Call for service.
Code 035 Function ServeRAID Result Text message Action Aborted Test setup error: No ServeRAID adapter found on system board or PCI bus Make sure that the ServeRAID adapter is properly installed. If the problem remains, replace the ServeRAID adapter. If the problem persists, call for service. Failed Adapter in slot n; adapter/drive configuration error Run the ServeRAID Configuration Utility.
Code 089 Function Microprocessor Result Failed Text message Invalid microprocessor in slot xyz or BIOS setup problem (where xyz identifies the microprocessor that is causing the error message) Processor in socket id xyz is installed but not functioning (where xyz identifies the microprocessor that is causing the error message) Action 1. Check the system error log for the related error messages. 2. If your server does not have the latest level BIOS installed, update the BIOS. 3.
Code Function Microprocessor Result Failed Text message Action VRM corresponding to Microprocessor in socket xyz is defective (where xyz identifies the microprocessor whose VRM is causing the error message) VRM corresponding to Microprocessor in socket id xyz is not installed (where xyz identifies the microprocessor whose VRM is causing the error message) 175 System thermal Failed Fan # n Replace the VRM. If the problem remains, call for service. Install a VRM.
Code 202 Function Result System cache Aborted Text message Action Test setup error: BIOS cannot access VPD information If your server does not have the latest level Test setup error: Corrupt DMI BIOS. Information in BIOS installed, update BIOS is not as expected the BIOS to the latest level and run the diagnostic program again. If the problem persists, call for service.
Code 264 Function Magnetic tape drive Result Aborted Text message Action Test setup error: No tape drive found Check the cable and power connections to the drive. Refer to the information that is provided with the tape drive. If the problem persists, call for service. Failed The load/mount test failed for device n on adapter m (where n is the number of the device and m is the adapter number) The Self-diagnostic failed for device n on adapter m.
Code 405 415 Function Ethernet Analog/digital modem Result Failed Not applicable Text message In PCI slot n Action (where n is the PCI slot number in which the failing Ethernet adapter is installed) Replace the Ethernet adapter in slot n. If the problem persists, call for service. On system board Call for service. No modem was detected 1. Verify that the modem is properly attached to the server. 2. If the problem remains, replace the modem. If the problem persists, call for service.
Recovering the BIOS code If the BIOS code has become damaged, such as from a power failure during a flash update, you can recover the BIOS code using the flash ROM page-swap jumper (J38) and a BIOS flash diskette. Note: You can obtain a BIOS flash diskette from one of the following sources: • Use the ServerGuide program to make a BIOS flash diskette. • Download a BIOS flash diskette from the World Wide Web. Go to http://www.ibm.
12. Turn off the server. 13. Move jumper J38 to the "hi" setting (pins 1 and 2) to return to normal startup mode. 14. Restart the server. Identifying problems using status LEDs Your server has LEDs to help you identify problems with some server components. These LEDs are part of the diagnostics that are built into the server. Use the illuminated LEDs to identify the failing or incorrectly installed components. Front panel and system board LEDs The system error LED is on the front panel inside the server.
Diagnostic LEDs You can use the diagnostic LEDs built into your server to quickly identify the type of system error that occurred. Your server is designed so that LEDs remain illuminated when the server shuts down, as long as the power supplies are operating properly. This feature helps you to isolate the problem if an error causes the server to shut down.
Error LED (on the system board or front panel) On System board or front panel LED on Cause Action VRM 1 or VRM 2 (system board) One of the microprocessor VRMs has failed, or a microprocessor VRM is installed in the wrong connector. 1. Check the microprocessor VRM error LEDs on the system board. If a microprocessor VRM error LED is on for a microprocessor VRM connector that has a terminator card installed instead of a microprocessor, the microprocessor VRMs are not installed in the correct order.
Troubleshooting charts You can use the troubleshooting charts in this section to find solutions to problems that have definite symptoms. Attention: If diagnostic error messages appear that are not listed in the following tables, make sure that your server has the latest levels of BIOS, ServeRAID, and diagnostics microcode installed. See “Starting the diagnostic programs” on page 88 to test the server.
Device Intermittent problems A problem occurs only occasionally and is difficult to detect. Suggested action Verify that: 1. All cables and cords are connected securely to the rear of the server and attached options. 2. When the server is turned on, air is flowing from the rear of the server at the fan grill. If there is no airflow, the fan is not working. This causes the server to overheat and shut down. 3.
Device Monitor problems The screen is blank. Suggested action Verify that: 1. The server power cord is plugged into the server and a working electrical outlet. 2. The monitor cables are connected properly. 3. The monitor is turned on and the Brightness and Contrast controls are adjusted correctly. If the items above are correct and the screen remains blank, call for service. Attention: In some memory configurations, the 3-3-3 beep code might sound during POST followed by a blank screen.
Device Option problems An IBM option that was just installed does not work. Suggested action Verify that: 1. The option is designed for the server. Refer to the "Server Support" flowchart for information about obtaining ServerProven™ compatibility information from the World Wide Web. 2. You followed the installation instructions that came with the option. 3. The option is installed correctly. 4. You have not loosened any other installed options or cables. 5.
Device Printer problems The printer does not work. Suggested action Verify that: 1. The printer is turned on and is online. 2. The printer signal cable is connected to the correct serial or parallel port on the server. Note: Non-IBM printer cables might cause unpredictable problems. 3. You have assigned the printer port correctly in your operating system or application program. 4. You have assigned the printer port correctly using the Configuration/Setup Utility program.
Device Suggested action Universal Serial Bus (USB) port problems A USB device does not work. Verify that: 1. You are not trying to use a USB device during POST if you have a standard (nonUSB) keyboard attached to the keyboard port. Note: If a standard (non-USB) keyboard is attached to the keyboard port, then the USB is disabled and no USB device will work during POST. 2. The correct USB device driver is installed. 3. Your operating system supports USB devices.
Ethernet controller problem The server stops running when loading device drivers. Suggested Action The PCI BIOS interrupt settings are incorrect. Check the following: • Determine if the interrupt (IRQ) setting assigned to the Ethernet controller is also assigned to another device in the Configuration/Setup Utility program. Although interrupt sharing is allowed for PCI devices, some devices do not function well when they share an interrupt with a dissimilar PCI device.
Ethernet controller messages The integrated Ethernet controller might display messages from the following device drivers: • • Novell™ NetWare™ or IntraNetWare Server ODI NDIS Adapter for level 4.0 (Windows NT) Novell NetWare or IntraNetWare server ODI driver teaming messages This section provides explanations of the error messages for the Novell NetWare or IntraNetWare server ODI driver, and suggested actions to resolve each problem.
Requested number of Secondary cards are not found. Explanation: The number of adapters specified in the bind command could not be located. Action: Verify the numbers and slot locations of the adapters to be bound. If the problem persists, contact your network supplier. Failed to create AFT group. Make Explanation: Binding of protocol failed. Protocol is either not bound to any sure that the drivers for supported adapter or is bound to more than one adapter in the group.
Error code (hex) Description 0x02 Explanation: Bad node address (multicast address). Action: Make sure that the locally administered address is valid, if one is specified. The address can not be a multicast address. 0x03 Explanation: Failed self-test. Action: Make sure a cable is attached to the Ethernet connector. If the problem persists, call for service. 0x0D Explanation: Could not allocate enough memory for transmit queues. Action: 1.
Ethernet teaming messages: Event ID Type Description 01 Error Explanation: Team Name and physical adapter name are the same. This is an invalid configuration. Action: Reconfigure the adapter team by double-clicking the PROSet icon in the control panel. 02 Error Explanation: Unable to allocate required resources. Action: Free some memory resources and restart. 03 Error Explanation: Unable to read required registry parameters.
Event ID Type Description 17 Informational Explanation: Team nn. Preferred primary adapter has been detected. Action: None. 18 Informational Explanation: Team nn. Preferred secondary adapter has been detected. Action: None. 19 Informational Explanation: Team nn. Preferred primary adapter took over. Action: None. 20 Informational Explanation: Team nn. Preferred secondary adapter took over. Action: None. 21 Warning Explanation: Team nn.Primary adapter does not sense any Probes.
Replacing the battery When replacing the battery, you must replace it with a lithium battery of the same type, from the same manufacturer. To avoid possible danger, read and follow the safety statement below. To order replacement batteries, call 1-800-772-2227 within the United States, and 1800-465-7999 or 1-800-465-6666 within Canada. Outside the U.S. and Canada, call your IBM reseller or IBM marketing representative.
3. Remove the battery: a. Use one finger to lift the battery clip over the battery. b. Use one finger to slightly slide the battery out from its socket. The spring mechanism will push the battery out toward you as you slide it from the socket. c. Use your thumb and index finger to pull the battery from under the battery clip. d. Ensure that the battery clip is touching the base of the battery socket by pressing gently on the clip. 4. Insert the new battery: a.
Getting help, service, and information If you need help, service, technical assistance, or just want more information about IBM products, you will find a wide variety of sources available from IBM to assist you. This section contains information about where to go for additional information about IBM and IBM products, what to do if you experience a problem with your computer, and whom to call for service should it be necessary.
The troubleshooting information or the diagnostic programs might tell you that you need additional or updated device drivers or other software. IBM maintains pages on the World Wide Web where you can get the latest technical information and download device drivers and updates. To access these pages, go to http://www.ibm.com/pc/support and follow the instructions.
If possible, be at your computer when you call. Please have the following information ready: • Machine Type and Model • Serial numbers of your IBM hardware products • Description of the problem • Exact wording of any error messages • Hardware and software configuration information Phone numbers are subject to change without notice. For the most up-to-date phone numbers, go to http://www.ibm.com/pc/support and click HelpCenter Phone List.
Other services IBM Update Connector is a remote communication tool that you can use with some IBM computers to communicate with the HelpCenter. Update Connector enables you to receive and download updates for some of the software that might come with your computer. With some computer models, you can register for International Warranty Service.
Appendix A. Product warranties and notices This chapter contains warranty and emission notices. It also contains trademarks and general-information notices. Warranty Statements The warranty statements consist of two parts: Part 1 and Part 2. Part 1 varies by country. Part 2 is the same for all countries. Be sure to read both the Part 1 that applies to your country and Part 2.
The IBM Warranty for Machines IBM warrants that each Machine 1) is free from defects in materials and workmanship and 2) conforms to IBM’s Official Published Specifications. The warranty period for a Machine is a specified, fixed period commencing on its Date of Installation. The date on your sales receipt is the Date of Installation, unless IBM or your reseller informs you otherwise.
When warranty service involves the exchange of a Machine or part, the item IBM or your reseller replaces becomes its property and the replacement becomes yours. You represent that all removed items are genuine and unaltered. The replacement may not be new, but will be in good working order and at least functionally equivalent to the item replaced. The replacement assumes the warranty service status of the replaced item.
This limit also applies to IBM’s suppliers and your reseller. It is the maximum for which IBM, its suppliers, and your reseller are collectively responsible.
Extent of Warranty The warranty does not cover the repair or exchange of a Machine resulting from misuse, accident, modification, unsuitable physical or operating environment, improper maintenance by you, or failure caused by a product for which IBM is not responsible. The warranty is voided by removal or alteration of Machine or parts identification labels.
You also agree to 1. ensure that the Machine is free of any legal obligations or restrictions that prevent its exchange; 2. obtain authorization from the owner to have IBM or your reseller service a Machine that you do not own; and 3. where applicable, before service is provided a. follow the problem determination, problem analysis, and service request procedures that IBM or your reseller provides, b. secure all programs, data, and funds contained in a Machine, c.
Part 2 - Worldwide Country-Unique Terms ASIA PACIFIC AUSTRALIA: The IBM Warranty for Machines: The following paragraph is added to this Section: The warranties specified in this Section are in addition to any rights you may have under the Trade Practices Act 1974 or other legislation and are only limited to the extent permitted by the applicable legislation.
Warranty Service If you purchased an IBM Machine in Austria, Belgium, Denmark, Estonia, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland or United Kingdom, you may obtain warranty service for that Machine in any of those countries from either (1) an IBM reseller approved to perform warranty service or (2) from IBM.
to damages caused by IBM with fraud or gross negligence and for express warranty. In item 2, replace "U.S. $100,000" with "1.000.000 DEM." The following sentence is added to the end of the first paragraph of item 2: IBM’s liability under this item is limited to the violation of essential contractual terms in cases of ordinary negligence.
otherwise gives rise to the claim. The following item is added to this paragraph: 3. breach of IBM’s obligations implied by Section 12 of the Sale of Goods Act 1979 or Section 2 of the Supply of Goods and Services Act 1982. Applicability of suppliers and resellers (unchanged). The following is added to the end of this Section: IBM’s entire liability and your sole remedy, whether in contract or in tort, in respect of any default will be limited to damages.
incorporated in new editions of the publication. IBM may make improvements and/or changes in the product(s) and/or the program(s) described in this publication at any time without notice. Any references in this publication to non-IBM Web sites are provided for convenience only and do not in any manner serve as an endorsement of those Web sites. The materials at those Web sites are not part of the materials for this IBM product, and use of those Web sites is at your own risk.
Other company, product, and service names may be trademarks or service marks of others. Important notes Processor speeds indicate the internal clock speed of the microprocessor; other factors also affect application performance. When referring to hard disk drive capacity, MB stands for 1000000 bytes and GB stands for 1000000000 bytes. Total user-accessible capacity may vary depending on operating environments.
Industry Canada Class A emission compliance statement This Class A digital apparatus complies with Canadian ICES-003. Avis de conformité à la réglementation d'Industrie Canada Cet appareil numérique de classe A est conforme à la norme NMB-003 du Canada. Australia and New Zealand Class A statement Attention: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Taiwan electrical emission statement Japanese Voluntary Control Council for Interference (VCCI) statement Power cords For your safety, IBM provides a power cord with a grounded attachment plug to use with this IBM product. To avoid electrical shock, always use the power cord and plug with a properly grounded outlet. IBM power cords used in the United States and Canada are listed by Underwriter’s Laboratories (UL) and certified by the Canadian Standards Association (CSA).
IBM power cord part number Used in these countries and regions 13F9940 Argentina, Australia, China (PRC), New Zealand, Papua New Guinea, Paraguay, Uruguay, Western Samoa 13F9979 Afghanistan, Algeria, Andorra, Angola, Austria, Belgium, Benin, Bulgaria, Burkina Faso, Burundi, Cameroon, Central African Rep., Chad, China (Macau S.A.R.
134 IBM® xSeries 220 User’s Reference
Index Numerics 933 MHz microprocessor installing 57 removing 58 A acoustical noise emissions 2 activity lights CD-ROM drive 5 diskette drive 5 hard disk drive 5, 49 SCSI 5, 49 adapter considerations 40 Ethernet 41, 72 fault tolerance 70 full length 40 installing 41 optional system-management 41 PCI 40 PCI bus 40 RAID 43, 51 Wake on LAN 72 adaptive load balancing 70 administrator password 16 advanced configuration options 18 advanced setup 14 air baffle removing 39 air circulation 10, 47 alternative start
error messages 108 failover 69 high performance modes 69 IntraNetWare error messages 108 NetWare error messages 108 pin-number assignments 72 port 62, 69 priority filters 70 priority packet mode 70 teaming 70 teaming error messages 111 troubleshooting information 106 VLAN 71 Windows NT error messages 109 expansion bays location 44 specifications 2 type 44 expansion enclosure problem 101 expansion slot cover 42 location 28 specifications 2 external options connecting 61 port connectors 29 F failover E
O option installing 27 problem 104 optional system-management adapter 41 override switch, password 16 P parallel port description 62 pin-number assignments 63 problem 104 parity checking, SCSI 18 password administrator 16 forgotten power-on 15 override switch 16 power-on 15 PCI adapters 40 bus A 40 bus B 40 bus control 14 configuration 14 Ethernet adapter slot 41, 72 expansion slots 40 plug and play Ethernet 69 slot/device information 15 system-management adapter slot 41 Wake on LAN adapter slot 72 pin-num
T tape drive installing 44, 46 teaming 69 teaming error messages 111 temperature air 2 terminator card microprocessor 55, 57 test log viewing diagnostic 89 thermal material 56, 57 time and date 13 trademarks 129 traffic class expediting 70 transfer rate SCSI devices 18 troubleshooting charts 101 Ethernet 106 information 73 turning off the server 8 turning on the server 7 U U11 connector 54 U12 connector 54 United States electronic emission Class A notice 130 United States FCC Class A notice 130 Universal
