IBM® TotalStorage Enterprise Tape System 3590 Operator Guide GA32-0330-13
IBM® TotalStorage Enterprise Tape System 3590 Operator Guide GA32-0330-13
Note! Before using this information and the product it supports, be sure to read the general information under “Notices” on page 115. Fourteenth Edition (October 2001) This edition of the IBM TotalStorage™ Enterprise Tape System 3590 Operator Guide , GA32-0330-13, obsoletes and replaces GA32-0330-12. Changes or additions are indicated by an asterisk or pound sign in the left margin. The following paragraph does not apply to any country where such provisions are inconsistent with local law.
Contents Figures . . . . . . . . . . Safety . . . . . . . . . Material Handling Safety . . Laser Safety and Compliance . . . . . . . . . . . . . . . . . v . vii . vii . vii Preface . . . . . . . . . . . . . ix Related Publications . . . . . . . . . ix IBM 3590 Publications . . . . . . . . ix IBM 3490 Publications . . . . . . . . ix IBM TotalStorage Enterprise Automated Tape Library (3494) Publications . . . . ix RS/6000® Publications . . . . . . . . x AS/400® Publications . . . . . . . .
Cleaning the Tape Path . . Model B11/E11 . . . . Model B1A/E1A . . . Cleaning Notification . . Cleaning the Tape Cartridge Cleaning the Magazine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chapter 6. Identifying Subsystem Problems . . . . . . . . . . . . Unable to Insert a Tape Cartridge . . . . . FID or ATTN on the Message Display . . . Tape Drive is Not Ready . . . . . . . . Leader Block Detaches from the Tape . . . SCSI Bus Problems . . . . . . . . . .
Figures 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. A14, C10, and C14 Operator Panel . . Operator Panel . . . . . . . . Options and Status Screen . . . . . 2x Label Icon . . . . . . . . . Library Locating Fiducials . . . . Intervention and Device Activity Messages . . . . . . . . . . Error Message Example . . . . . Example of Selectable Options . . . Operator Menus . . . . . . . . Microcode Level Menu . . . . . Confirmation Menu . . . . . . Confirm Mode Change-Proceed Menu 3590 ACF and Magazine . . . . .
vi 3590 Operator Guide
Safety Material Handling Safety CAUTION: > 28 kg (61 lb) v Products weighing between 18 kg (39.7 lb) and 32 kg (70.5 lb) require 2 or more persons for safe handling. v Products weighing between 32 kg (70.5 lb) and 55 kg (121.2 lb) require 3 or more persons for safe handling. v Products weighing above 55 kg (121.2 lb) are non-portable equipment. Laser Safety and Compliance These products contain components that comply with performance standards that are set by the U.S. Food and Drug Administration.
viii 3590 Operator Guide
Preface Related Publications The following publications provide related information about the IBM SCSI tape drive, medium changer, and library device drivers: IBM 3590 Publications # # v IBM TotalStorage Silo Compatible Tape Frame 3590 Introduction, Planning, and User’s Guide, GA32-0366 # * # # # # v IBM TotalStorage Enterprise Tape System 3590 Operator Guide, GA32-0330 v IBM Magstar® 3590 Tape Subsystem Hardware Reference, GA32-0331 v IBM TotalStorage Silo Compatible Tape Drive Frame Maintenance Inform
RS/6000® Publications For additional information about RS/6000® systems, see: v RS/6000 Getting Started: Using RS/6000, GC23-2521 v RS/6000 Getting Started: Managing RS/6000, GC23-2378 v RS/6000 Problem Solving Guide, SC23-2204 v RS/6000 V4 Problem Solving Guide, SC23-2606 v RS/6000 V4 Message Guide & Reference, SC23-2641 v RS/6000 Planning for System Installation, SA38-0508 v RS/6000 7017 Rack Installation and Service Guide, SA48-0548 AS/400® Publications For additional information about AS/400® systems,
IBM FICON™ Publications v Planning for: Fiber Optic Links (ESCON, FICON, Coupling Links, and Open system Adapters), GA23-0367 v Maintenance Information for: Fiber Optic Links (ESCON, FICON, Coupling Links, and Open system Adapters), SY27-2597 v Fiber Channel Connection (FICON) I/O Interface Physical Layer, SA24-7172 v Planning for the ED-5000 Enterprise Fibre Channel Director v , SA22-7456 v FICON (FCV Mode) Planning Guide, SG24-5445 (available at www.redbooks.ibm.
v Virtual Machine/Enterprise System Architecture General Information, GC24-5550 HP Publications v HP-UX Reference, Volumes 1, 2, and 3 Hewlett-Packard Company, Part B2355-90033 v System Administration Tasks, HP-UX Release 9.0 Hewlett-Packard Company, Part B2355-90040 SUN Publications v Solaris 2.x: Adding and Maintaining Peripherals v SunOS 5.x: User’s Guide to System Administration v SunOS 5.
McDATA Switch Lists the IBM McDATA Enterprise Fibre Channel Director. v http://www.storage.ibm.com/ibmsan/director1.htm FICON Lists updated information FICON. v http://www.storage.ibm.com/hardsoft/tape/3590/ficon.html Open Systems support This site describes hardware and software for Midrange and Open Systems Connectivity for IBM TotalStorage 3590. v http://www.storage.ibm.com/hardsoft/tape/3590/3590opn.html Redbooks Lists the IBM Redbooks: v http://www.redbooks.ibm.
When you send information to IBM, you grant IBM a nonexclusive right to use or distribute the information in any way it believes appropriate without incurring any obligation to you.
Summary of Changes This release includes information on the following product enhancements. Fourteenth Edition * * * This edition introduces capacity and performance enhancements and new FICON cable options for the IBM TotalStorage Enterprise Tape Controller 3590 Model A60, as well as the IBM TotalStorage name brand. Thirteenth Edition This edition introduces FICON shortwave and 3590 Fibre Channel drive attachment with a 3590 IBM TotalStorage Enterprise Tape Controller Model A60.
Tenth Edition This release includes information on Fibre Channel Attachment features. With Fibre Channel Attachment, 3590 Model E is now capable of delivering a data rate of 42 MB/s maximum sustained data rate (with 3:1 data compression) and up to 100 MB/s maximum instantaneous data rate. Fibre Channel Attachment has increased the maximum distance to 500 meters. It is possible to extend the maximum distance to 10 kilometers using fibre components.
The 256-track serpentine format results in a tape capacity of 20GB of uncompressed data on the IBM® 3590 High Performance Cartridge Tape. Prior model investments are protected with upgrade capability available. Refer to the IBM TotalStorage Enterprise Tape System 3590 Introduction and Planning Guide for a summary of Models E1A and E11 attachments.
xviii 3590 Operator Guide
Chapter 1. Introduction The IBM TotalStorage Enterprise Tape System 3590 provides high capacity, performance, reliability, and a wide range of host connectivity. The IBM 3590 has the following functions: v The 3590 creates tapes for archival files. v The 3590 backs up and restores systems in case of system or disk storage problems. v The 3590 stores high-speed, high-capacity sequential application data sets. v The 3590 stores temporary data sets.
* * * * * SCSI Ultra/wide data rate and the ESCON or FICON data rate. The Fibre Channel Attachment data rate is an instantaneous 100MB per second. Also, the SCSI Ultra/wide instantaneous data rate is up to 40MB per second. For ESCON, the channel-instantaneous rate is 17 MB per second, and for FICON it is 100MB per second. * * * * * * For more information about the following topics, see the IBM TotalStorage Enterprise Tape System 3590 Introduction and Planning Guide.
Chapter 2. A14, C10, and C14 Control Unit Operator Panel The operator panel, shown in Figure 1, provides a means for the customer to either power on or power off the 3590 A00, A50, or A60 Subsystem. In addition, it provides power status feedback, whether or not errors are present on the A00, A50, or A60 control unit. The following information describes the operator panel switches and indicators: Figure 1. A14, C10, and C14 Operator Panel © Copyright IBM Corp.
The following lists the components of the operator panel: 1. 1 Unit Emergency Switch v With the unit emergency power off (EPO) switch in the up position, it is turned “on” and the AC power is applied to the entire subsystem. v With the EPO switch in the down position, it is turned “off” and all power is removed from the subsystem. 2. 2 System Power Switch v In the upward position, a power on sequence will initiate. v In the downward position, a power off sequence will initiate. 3.
Chapter 3. Drive Operator Panel and Controls Operator Panel Display The operator panel provides a menu-driven operator and service interface through a liquid crystal display assembly. Displays include operator menus and service menus, device status, activities, error conditions, and data. See Table 1 for panel displayed characters. Table 1. Message-Display Symbols Characters Symbols Alphabetic A through Z Numeric 0123456789 National “@ $ #” Special “, .
specifies the SCSI ID for that interface. (0 through 9 and A through F correspond with bits 0 through 15 on the SCSI 2-byte wide interface.) Each Fibre Channel ID consists of six hexidecimal characters that specify the Fibre ID for that interface. At each power-on, this address is retrieved from nonvolatile storage. The online and offline selections control determines whether or not the device is logically enabled to communicate on the interface. Use “Services Menu” on page 33 to access this function.
Figure 2. Operator Panel From left to right in Figure 2, the push buttons and the indicator are as follows: Reset 1 A push button that allows the service representative to perform a device power-on reset. Note: It is recommended that all SCSI ports be taken offline before resetting the drive. See “Services Menu” on page 33. Change Mode 2 A push button that allows the service representative to toggle between service representative mode and Normal mode.
Enter 5 A push button that allows the operator or the service representative to select the menu option at the location of the cursor arrow. Processor Check 6 An indicator LED that switches on for 10 to 20 seconds during a normal power-on or a power-on reset. If no fault is detected, the LED switches off. If the LED remains on, the 3590 requires service.
Table 2 identifies the various drive type indicators 2 of Figure 3 and Table 3 describes the panel areas it illustrates. Figure 3. Options and Status Screen Table 2.
Table 3. Options and Status Area ACF Mode 1 Description Displays as manual, automatic, system, accumulate, or random when the ACF is installed. When the operator changes modes, any current ACF operation (cartridges in transit) are completed before the request is granted. Drive Type 2 Table 2 provides the history of drive type indicators. v Cleaning: A cleaning cartridge is in the device.
Table 3. Options and Status (continued) Area Description Messages: v Area 4 and 5 is a dual-use area that can be used for prompts and messages. – SCSI messages include: PORT0 ADDR=n ONLINE or OFFLINE . PORT1 ADDR=n ONLINE or OFFLINE . (‘n’ can be in the range 0–F.) For SCSI port 0 or 1 (PORT0 or PORT1), the last assigned SCSI address (ADDR=n) is listed with each port’s online or offline status (ONLINE or OFFLINE ).
Note: The 3590 tape drives that are capable to receive the Extended High Performance Cartridge Tape are labeled 2x on the back of drive chassis. For B Model drives, the 2x label is placed below the serial number label. For Ultra and E Model drives, the 2x label is located below the respective Ultra and E labels which, in turn, are located below the serial number label. See Figure 4 for an illustration of the tape-icon label. The 2x information is available in Table 3 on page 10. Figure 4.
Fiducials Figure 5. Library Locating Fiducials Figure 5 shows a B1A or E1A with a single fiducial 1 . The fiducial is used by cartridge-handling devices to locate and remember where the tape subsystem device is installed. Do not cover or change the fiducial. Drive Power The power switch is located on the back of each device. This toggle switch controls the distribution of ac power to the associated device.
Processor Check Indicator The processor check indicator indicates that the model-unique Licensed Internal Code is not following its normal sequence. A symbol that looks like a wrench identifies the Processor Check indicator on the operator panel. See Figure 2 on page 7 definitions for more details. File Protected Icons The status icons area of the operator panel displays the file-protected icons (see Figure 3 on page 9).
relative to the beginning and end-of-volume. If the device is rewinding, the tape-position indicator illustrates the beginning and end-of-tape. Logically shortened tape is displayed normally, but the rate of change is faster than normal length tapes. Dump Icon The status area of the operator panel displays the dump icon, (see Figure 3 on page 9). The dump icon appears when a trace is available and remains on the screen to indicate that the 3590 stores the trace data.
Intervention Messages The intervention screen displays intervention messages on the operator panel. The intervention screen consists of an 8-character intervention message that is displayed in a large font and a prompt. The prompt indicates that pressing Enter allows access to the Options menu. The screen also has device status information and a 2-line message area in the standard font. A drive type is displayed (see Table 2 on page 9).
Table 4. Intervention and Device Activity Messages (continued) Message Attention Message Meaning These messages indicate error conditions that operators can resolve, such as Lock magazine. See Table 5 on page 24. Routine Messages Mvolser The M prompts the operator to mount volser in the priority cell. *CLEAN This message prefixed with an asterisk (*) prompts the operator to put a cleaning cartridge in the priority cell. Dvolser The D prompts the operator to remove volser from the priority cell.
FID 1 C6 1 2 3 4 5 >Operator Options 6 Figure 7. Error Message Example The service representative makes note of the part identifier (FID) 1 and the severity code 2 . The service representative then uses the FID number 3 to enter the Maintenance Package. The message area of 4 , 5 , and 6 hex data is support information to help determine if model-unique Licensed Internal Code causes the fault.
v FID4 Messages A FID4 message indicates that some service circuitry failed. For example, FID4 E4 could indicate that a parity-check circuit failed. Message Priority and Display Rules This section describes message priorities and their creation, deletion, display, and storage. Message Action Term Definitions This description defines the following message action terms: Display Display means to present a message on the operator panel display.
4. FID 2 5. FID 3 6. FID 4 Note: “Message Life Cycle Rules” describes the priority relationships between individual Routine Messages. Message Life Cycle Rules “Message life cycle rules” are the rules that govern creating, replacing, displaying, storing, and deleting messages.
v Stored: A Mount message is stored when a cartridge is unloading and a Demount message is displayed. v Displayed: A stored Mount message is displayed when the previous Demount message is deleted. Previous Demount messages are deleted when the accessor removes a cartridge from the loader. v Deletion: The device removes a Mount message from the display when it initiates a cartridge load. When the device transitions to the Ready state (stored or displayed message), it deletes the Mount message.
mount portion of the demount/mount message is displayed. For a loaded cartridge, the demount portion of the message is deleted when the accessor removes a cartridge from the loader. A message control of “100” (alternate message) will cause the demount and mount messages to alternate as long as a cartridge is loaded. Demount is deleted when a cartridge is unloaded. Routine Messages—General (Custom): v Creation: A General message is created when a Display Message is received that requests a General message.
FID 2: v Creation: A FID 2 message is created when the device microcode detects a permanent failure of a serious nature that puts the device in a degraded state. The drive can still be used, but it is in a less available state. If a subsequent FID 2 message is generated, it replaces any earlier FID 2 messages. v Stored: A FID 2 message is stored and overlaid when a higher priority message is displayed. v Displayed: A FID 2 message is displayed when it is not overlaid by a higher priority message.
Table 5. Operator Messages Message Operator Response ACF IRQ FAULT Service representative intervention required. ACF MESSAGE MISSING Service representative intervention required. Operator intervention required. ACF NOT ENABLED Ensure cartridge is in ACF import position. For more information, see “Cartridge Magazine Positions” on page 52 and “Chapter 6. Identifying Subsystem Problems” on page 73.
Table 5. Operator Messages (continued) Message Operator Response Service representative intervention required. FEED OVERCURRENT Report any FID codes to your service representative. FSC TRAP TAKEN Service representative intervention required. Operator intervention or possible service representative corrective action required. HEAD CALIB FAILED. Select Unload on the operator panel and press Enter. If the device fails to unload the cartridge, note any FID messages and call your service representative.
Table 5. Operator Messages (continued) Message Operator Response Operator action required: MAGAZINE EXPORT ER When the tape subsystem placed a cartridge in the magazine, the cartridge was placed either beyond or in front of the Export position. When the cartridge is not in the true Export position, it is possible that a cartridge placed in front of the Export position may unexpectedly be reused.
Table 5. Operator Messages (continued) Message Operator Response Operator action required: NO MAGAZINE The tape subsystem does not detect a magazine in the ACF. If a magazine is installed in the ACF, clear the condition by removing and then replacing the magazine in the ACF. Try another or a different magazine. If the condition persists or a FID message is displayed, report any FID codes to your service representative.
Table 5. Operator Messages (continued) Message Operator Response Operator intervention or possible service representative corrective action required. TENSION DROPPED Select Unload on the operator panel and press Enter. If the device fails to unload the cartridge, note any FID messages and call your service representative. 1. Operator intervention required. TRANSPORT FULL 2. The drive attempted to unload a cartridge, but had no place to put it.
option 1 when there is no cartridge in the device. The Unload Drive option 2 shows the darker font, which indicates that it can be selected. Figure 8. Example of Selectable Options If you move the cursor ( ) to 1 and press Enter, the selection responds with the normal font 2 momentarily. It then returns to the lighter font. The 3590 will not perform any action. Chapter 3.
Operator Flow Chart Figure 9 shows the operator menus with panel functions. Figure 9.
Operator Menus Operator menus are available at the successful completion of the power-on self-test (POST). Options Menu Table 6 shows the Options menu. Table 6. Options Function Next Menu Start/Allow Load (Model C12/C14 only) — Set ACF Mode... “Set ACF Mode Menu” on page 32 Unload Drive — Services... “Services Menu” on page 33 Note: Supplemental Message Line 1: Supplemental Message Line 2: Start Enables the ACF on Models E11 or B11.
Set ACF Mode Menu Table 7 shows the Set ACF Mode menu. Table 7. Set ACF Mode Function Next Menu Cancel “Options Menu” on page 31 System “Options Menu” on page 31 Automatic “Options Menu” on page 31 Manual “Options Menu” on page 31 Accumulate “Options Menu” on page 31 Random (B11 model only) “Options Menu” on page 31 Random 2-LUN “Options Menu” on page 31 Note: Supplemental Message Line 1: Supplemental Message Line 2: Cancel Causes the “Options Menu” on page 31 to appear.
Services Menu Table 8 shows the Services menu. Table 8. Services Function Next Menu Cancel “Options Menu” on page 31 Set Online. “Set Online Menu” on page 35 Set Offline. “Set Offline Menu” on page 36 Set Address... (SCSI Attached Drives Only) “Set Address Menu” on page 37 Fibre Address... (Fibre Attached Drives Only) “Fibre Address Menu” on page 40 Change Language... “Change Language Menu” on page 45 Statistics...
Each AL_PA. consists of two hexadecimal numbers. After each adress is set, the device will automatically run Loop Initialization (LIP). Change Language Allows the operator to select the operator panel language. Statistics Displays the number of times certain events occurred. Refresh Tape This option is selectable only when a tape is loaded. It will locate to the end of the tape and rewind to its beginning. Microcode Level Displays the microcode EC level that is in DRAM. Figure 10 shows an example.
Figure 11. Confirmation Menu Cancel Causes the model-unique Licensed Internal Code to ignore the selection and causes the Services menu to appear. Proceed Causes the model-unique Licensed Internal Code to perform the operation that is chosen (Reset Drive or Force Error Dump) from the Services menu. Set Online Menu Table 9 shows the Set Online menu. Table 9.
Set Offline Menu Table 10 shows the Set Offline menu. Table 10. Set Offline Function Next Menu Cancel “Services Menu” on page 33 Port 0 “Confirm Offline Menu” on page 37 or “Options Menu” on page 31 Port 1 “Confirm Offline Menu” on page 37 or “Options Menu” on page 31 Both “Confirm Offline Menu” on page 37 Note: Supplemental Message Line 1: Supplemental Message Line 2: Cancel Causes the “Services Menu” on page 33 to appear. Port 0 Causes SCSI port 0 to be set offline.
Confirm Offline Menu Table 11 shows the Confirm Offline menu. Table 11. Confirm Offline Function Next Menu Cancel “Set Offline Menu” on page 36 Proceed “Options Menu” on page 31 Note: Supplemental Message Line 1: Caution: Data loss Supplemental Message Line 2: risk Cancel Cancels the offline request and causes the “Set Offline Menu” on page 36 to appear. Proceed Forces the ports offline. If write activity exists, any write data in the device is lost. The Proceed option causes the job to end.
Set Port 0 Address Menu Table 13 shows the Set Port 0 Address menu. Table 13. Set Port 0 Address Function Next Menu Cancel “Set Address Menu” on page 37 0 “Options Menu” on page 31 1 “Options Menu” on page 31 ... “Options Menu” on page 31 F “Options Menu” on page 31 Note: Supplemental Message Line 1: Change made after Supplemental Message Line 2: next power on Cancel Causes the “Set Address Menu” on page 37 to appear. Allows the operator to set the address of SCSI port 0.
Set Port 1 Address Menu Table 14 shows the Set Port 1 Address menu. Table 14. Set Port 1 Address Function Next Menu Cancel “Set Address Menu” on page 37 0 “Options Menu” on page 31 1 “Options Menu” on page 31 ... “Options Menu” on page 31 F “Options Menu” on page 31 Note: Supplemental Message Line 1: Change made after Supplemental Message Line 2: next power on Cancel Causes the “Set Address Menu” on page 37 to appear. Allows the operator to set the address of SCSI port 1.
Fibre Address Menu Table 15 shows the Fibre Address menu. Table 15. Set Address Function Next Menu Cancel “Services Menu” on page 33 Show Node Names “Show Node Name Menu” Show Port Names “Show Port Names Menu” on page 41 Set Port 0... “Set Port 0 Fibre Address Menu” on page 42 Set Port 1... “Set Port 1 Fibre Address Menu” on page 43 Cancel Causes the “Services Menu” on page 33 to appear. Show Node Name Causes the “Show Node Name Menu” to appear.
Show Port Names Menu Table 17 shows the Show Port Names menu. Table 17. Show Port Names Function Next Menu Cancel “Fibre Address Menu” on page 40 Port 0 Names 0123456789ABCDEF (16 character #) “Fibre Address Menu” on page 40 Port 1 Names 0123456789ABCDEF (16 character #) “Fibre Address Menu” on page 40 Cancel Selecting this function causes the “Fibre Address Menu” on page 40 to appear. Port 0 Name The number that appears is a unique address for the physical port.
Set Port 0 Fibre Address Menu Table 18 shows the Set Port 0 Fibre Address menu. Table 18. Set Port 0 Fibre Address Function Next Menu Cancel “Fibre Address Menu” on page 40 Set Hard Address “Set Hard Address Menu” on page 44 Use Soft Address “Use Soft Address Menu” on page 45 Cancel Causes the “Fibre Address Menu” on page 40 to appear. Set Hard Address Causes the “Set Hard Address Menu” on page 44 to appear.
Set Port 1 Fibre Address Menu Table 19 shows the Set Port 1 Fibre Address menu. Table 19. Set Port 0 Fibre Address Function Next Menu Cancel “Fibre Address Menu” on page 40 Set Hard Address “Set Hard Address Menu” on page 44 Use Soft Address “Use Soft Address Menu” on page 45 Cancel Causes the “Fibre Address Menu” on page 40 to appear. Set Hard Address Causes the “Set Hard Address Menu” on page 44 to appear.
Set Hard Address Menu Not all values in the range from 00 to FF are valid for an AL_PA. This menu will prompt you with the previous and next valid AL_PA values. Table 20 shows the Set Hard Address menu. Table 20. Set Hard Address Function Next Menu Cancel “Fibre Address Menu” on page 40 c — d — Save Data “Fibre Address Menu” on page 40 Notes: 1. Supplemental Message Line 1: v n = the port number (0 or 1) v cd = the last AL_PA value saved (see 4 and 5 in Table 3 on page 10) 2.
Use Soft Address Menu Table 21 shows the Use Soft Address menu. Table 21. Use Soft Address Function Next Menu Continue “Fibre Address Menu” on page 40 Continue This function causes the “Fibre Address Menu” on page 40 to appear. It indicates that a soft address algorithm is to be used. It also sets the hard adress to FF. Change Language Menu Table 22 shows the Change Language menu. Table 22.
Statistics Menu Table 23 shows the Statistics menu. Table 23. Statistics Function Next Menu Cancel “Services Menu” on page 33 Show Statistics... “Show Statistics Menu” on page 47 Save “Statistics Menu” Note: Supplemental Message Line 1: Supplemental Message Line 2: Cancel Causes the “Services Menu” on page 33 to appear. Show Statistics Causes “Show Statistics Menu” on page 47 to appear. Save 46 3590 Operator Guide Causes the statistics to be saved in nonvolatile storage.
Show Statistics Menu Table 24 is an example of the Show Statistics menu. Table 24. Show Statistics Function Next Menu Cancel “Statistics Menu” on page 46 Mounts to Drv “Show Statistics Menu” Priority Mnts “Show Statistics Menu” Magazine Mnts “Show Statistics Menu” Clean Mounts “Show Statistics Menu” Pwr On Hrs “Show Statistics Menu” Note: Supplemental Message Line 1: Supplemental Message Line 2: Cancel Causes the “Statistics Menu” on page 46 to appear.
Confirm Mode Change Menu Table 25 shows the Confirm Mode Change menu. Table 25. Confirm Mode Change Function Next Menu Cancel Previous menu Proceed “Options Menu” on page 31 if no job, or Figure 12 if job is in progress.
Chapter 4. Automatic Cartridge Facility (ACF) and Magazine This chapter describes the Automatic Cartridge Facility (ACF) and the magazine. ACF Description Figure 13 shows the Automatic Cartridge Facility with a loaded magazine. Figure 13. 3590 ACF and Magazine The following lists the ACF components: 1 Operator Panel 2 Priority Cell 3 Magazine 4 Machine Side of Magazine 5 Magazine Cartridge Lock 6 Magazine Door 7 Lock Button © Copyright IBM Corp.
8 Magazine LEDs 9 Handle 10 Operator Side of Magazine Note: The operator panel (see item 1 ) is located on top of the front bezel above the ACF. It is moveable for easier viewing by the operator. The ACF holds a total of 10 cartridges. Cartridges are contained in both a magazine, and in a single priority cell (see item 2 ) which has a capacity of one cartridge. The ACF is attached to the tape subsystem mechanism.
Notes: 1. A sensing device detects any cartridges positioned beyond the import position and prevents operation of the cartridge transport. 2. Cartridges can be loaded or unloaded from the magazine from either side of the magazine before it is installed in the 3590. All cartridges must be loaded with the label side up and the leader block towards the machine side of the magazine. When the drive ejects a cartridge, in all modes except Random mode, a cartridge is placed in the export position.
ACF Magazine Cartridge Magazine Positions Figure 14 shows a partially loaded magazine. The magazine (see item 1 ) includes two cartridge positions. 1 6 2 5 4 3 A14U0003 7 Figure 14. Left View of the 3590 Magazine Cartridge Positions The following lists the Magazine Cartridge positions: 1 3 5 7 Magazine Magazine Door Import Position Label Positioning 2 Cartridges 4 Cartridge Lock 6 Export Position Notes: 1.
Import Position The cartridge is inserted into the magazine (see item 5 ) until it comes to the second detent position towards the ACF. Export Position The cartridge is inserted into the magazine (see item 6 ) until it comes to the first detent position. The export position protrudes from the magazine body (away from the ACF). Magazine Weight The ACF magazine, 3M part 78-A068-2883-2, weighs 0.68 Kg (1.5 lbs) and each cartridge weighs 0.23 Kg (0.5 lbs).
ACF Door and Lock Function The magazine has a door ( 3 in Figure 14 on page 52) that extends along the entire length of the magazine. The door is located at the front left side of the magazine when viewed from the front. A hand-operated slider is located in the middle of the magazine frame. The two positions for the magazine lock are as follows: Unlocked The slider is towards the front of the magazine to enable insertion and removal of the cartridge from the magazine.
Inserting the Magazine in the 3590 1. One hand holds the handle. The other hand holds the body of the magazine at a 45° angle. 2. Insert the lower front of the magazine into the ACF as shown in Figure 15 on page 54 so that the front of the magazine is inside the ACF lip 1 . 3. Pivot the magazine top towards the ACF, until the magazine is flush with the front of the ACF. 4. Push the magazine handle into the ACF lockbar to secure the magazine in the ACF.
Automatic Cartridges that are put into the magazine are automatically fed into the drive loader one after another until the entire magazine is processed. System Cartridges that are put into the magazine are fed to the drive loader one after another under the attaching system’s command. This continues until the entire magazine is processed. Note: Not all hosts support System mode. Random and Random 2-LUN Operates as a small library. All cartridge moves are made under the attaching system’s commands.
8. If the ACF is instructed to unload a cartridge to an uninstalled magazine, the ACF tries to unload the cartridge to the priority cell. (See Note 9.) The cell-status indicator LED is set to alert (solid yellow) for the priority cell. 9.
– An attention condition is detected in the ACF; for example, an extra cartridge condition. – The magazine is not installed; choosing Start causes the ACF to return to the disabled state. v Operation 1. If the ACF is disabled and in Manual mode, and the operator chooses Start on the operator panel, the ACF becomes enabled. It then verifies that at least one cartridge is in the import position of the magazine.
magazine cell. This allows the operator to insert specific cartridges into the priority cell. The magazine accumulates processed cartridges for pickup by the operator. When the ACF is in Accumulate mode, the following applies (see also “ACF Notes” on page 56): v Initial conditions – Accumulate mode must be selected from the SET ACF MODE menu. – We recommend that, initially, the magazine be empty, even though this is not a required condition.
into the priority cell again, if possible. The priority cell cell-status indicator LED is then set to alert (steady yellow). See step 9 on page 57 if the priority cell is also full. Automatic Mode Automatic mode provides the operator a mechanism to keep the drive continually fed with cartridges from the magazine. After enabling the ACF, it automatically feeds cartridges to the device until all the cartridges in the magazines are processed.
so, the ACF indexes down the magazine until it finds the first cell with a cartridge in the import position. The ACF sets the cell-status indicator LED for that cell to in-use (steady green) and moves the cartridge from the cell to the device. 2. If the ACF is disabled and in Automatic mode and a cartridge is placed in the import position of the priority cell, the ACF is enabled. It then loads the cartridge in the device, and sets the cell-status indicator LED to in-use (steady green) for the priority cell.
– The ACF is initialized so the top cell of the magazine is considered the current cell location. v Enabling conditions: Two ways to enable System mode follow: – Select Start ACF on the operator panel if there is a loadable cartridge in the magazine. – Insert a cartridge in the import position of the priority cell. v Disabling conditions: The ACF becomes disabled in System mode as follows: – A magazine or priority cartridge is processed and returned to its original cell.
Random and Random 2-LUN Modes Random mode is designed to act as a small, self-contained library of up to 10 cartridges, controlled by the attaching host. The attaching host uses the SCSI Medium Mover commands to select a cartridge from a given cell and move it to its destination cell. Control of the source and destination cells are left entirely to the attaching host. Random 2-LUN mode behaves the same as Random mode. The 2-LUN allows software to control the ACF in a different manner.
– Random mode must be selected from the SET ACF MODE menu. v Enabling conditions: Random mode is enabled if all the following conditions are met: – The magazine is installed in the ACF. – The magazine lock is in the locked state. – A valid Move Medium command is received. v Disabling conditions: The ACF is disabled in Random mode if one of the following conditions are met: – The magazine is removed from the ACF. – The magazine is unlocked.
v “Cell Status: Steady Green–In-Use Indicator LED” on page 66. Cell Status: Flashing Yellow–Attention indicator LED The device requires operator assistance. Table 26 describes the Attention condition. There will be a corresponding operator panel ATTN ACF message in the case where the LEDs indicate attention. Table 26.
Cell Status: Steady Yellow–Alert Conditions This condition does not immediately preclude machine operation, but may, unless the condition is cleared soon. Table 27 describes the Alert condition: Table 27. Cell Status Indicator LEDs Steady Yellow–Alert Conditions Indicator LED State Description of the Condition Accumulate, Automatic, Manual, or System modes only–Magazine Not Installed or is locked. LEDs return to normal when condition is cleared.
Chapter 5. Cleaning Procedures Clean the tape path and the cartridges. This prevents errors that are caused by dirt. A cleaning cartridge is shipped with the first B1A and B11 in each installation. Replace the cleaning cartridge after 100 uses. You can keep track of the usage number by marking the label provided with each cartridge. Note: The 3590 cleaning cartridge, IBM part 05H4435, or equivalent, is for use only in a 3590 tape subsystem. Properly label all cleaner cartridges for their intended use.
Attention: Do not use a china-marking (grease) pencil on the label. Insert only clean and undamaged cleaning cartridges into a tape subsystem. Cleaning cartridge components from the bottom view: 1 gray plastic inserts 2 identifier notches 3 leader block 4 finger notch Cleaning the Tape Path The drive will display a *CLEAN message and display a CLEAN ICON after processing a predetermined amount of tape, or when reaching certain conditions.
automatically cleans, when a *CLEAN message is displayed, load a cleaning cartridge in the drive. The cleaning cartridge will complete its cycle and then unload. Cleaning Notification Two types of cleaning notification are available: v Operator Panel Cleaning Notification v SCSI interface cleaning notification The sections that follow describe each type of notification.
Cleaning the Tape Cartridge Before you insert a cartridge into a drive or a magazine, inspect the cartridge for damage or dirt. Damaged or dirty cartridges can reduce subsystem reliability and cause the loss of recorded data. If dirt appears on the cartridge, wipe the outside surfaces. Especially wipe the sides of the cartridge, with a lint-free cloth (IBM part 2108930). Lightly moisten the cloth with IBM Tape Unit Cleaner, 05H3929. For cleaning magazines, see “Cleaning the Magazine” on page 71.
Cleaning the Magazine The High Performance Cartridge Tape and Extended High Performance Cartridge Tape subsystems are highly refined mechanical devices. To maintain the maximum performance, the operator should take time to inspect and clean the magazine and the cartridges. Damaged or dirty magazines or cartridges can reduce subsystem reliability and cause the loss of recorded data. Monitor the conditions of all magazines and cartridges for contaminants.
72 3590 Operator Guide
Chapter 6. Identifying Subsystem Problems This chapter identifies some of the problems that can occur with the Subsystem. Unable to Insert a Tape Cartridge If you cannot insert a tape cartridge in the drive, perform the following steps: 1. Inspect the tape cartridge for damage. See “Damaged Cartridges” on page 87. 2. Try to load another cartridge in the tape subsystem. If the new cartridge can be inserted in the drive, the original cartridge may be defective. Inspect the cartridge for damage.
3. If the drive does not become ready, and no messages are displayed, call your service representative. If a FID or ATTN message appears on the message display, record the code message and see “FID or ATTN on the Message Display” on page 73. Leader Block Detaches from the Tape Figure 18 shows a cartridge with a detached leader block. Figure 18.
Replacement of the leader block is a temporary repair. It allows the operator to insert the cartridge, with the file-protect selector (see item 3 ) set to the file-protect position, once. This, in turn, allows the data to be copied to a new cartridge. After you repair the leader block and recover the data, do not use the cartridge again. SCSI Bus Problems See “SCSI Bus” on page 105. Fibre Channel Problems See “Fibre Channel” on page 109.
Message Display is Blank If the message display is blank, perform the following steps: 1. If power is not supplied to the rack or device, correct the problem before you proceed to the next step. 2. To turn on the main power supply, if the main service power to the subsystem is not on, follow the operating procedures for your host system. 3. If the message display is blank after this procedure, call your service representative. Tape/Drive Read or Write Problems See “Appendix A.
ACF Recovery Procedure ACFs with flashing attention indicator LEDs, or ACFs with continuous attention indicator LEDs that are not flashing, use the recovery procedures that are listed below. Perform the recovery procedure that is appropriate for your loader’s condition. Attention Indicator LED Flashes If the attention indicator LED flashes, do the following: 1. Remove the cartridge from the feed position (if present). 2. Add cartridges to the magazine if the loader is in Auto or System mode. 3.
ATTN message appears on the message display, record the error code and report it to your service representative.
Chapter 7. 3590 High Performance Cartridge Tape and Extended High Performance Cartridge Tape The 3590 tape drive has a bidirectional read/write head with a recording format of 256 tracks for Exx models and 128 tracks for Bxx models. Both series of models concurrently processes 16 tracks per group. The bidirectional head writes 16 tracks from the load point to the physical end of tape. It then writes 16 tracks from the physical end of tape back to the load point.
v v v v 3 4 5 6 Leader block latch File-protect selector (dependent on supplier) File-protect selector (dependent on supplier) Cartridge case (black) v 7 Labels v 8 Identification notches (blue for High Performance Cartridge Tape and green for Extended High Performance Cartridge Tape) Note: The leader block (see item 1 ) is shown unlatched with a length of tape (see item 2 ) which extends from the cartridge. This is for illustration purposes only.
The tape cartridges have blue insert identification notches for High Performance Cartridge Tape and green notches for Extended High Performance Cartridge Tape. The leader block assembly is blue for High Performance Cartridge Tape and green for Extended High Performance Cartridge Tape. The 3590 cleaning cartridge has gray insert identification notches and a gray leader block assembly. The IBM 3590 High Performance Cartridge Tape is not compatible with 3480, 3490, or 3490E drives.
Tape Handling and Storage Advantages Magnetic tape storage and handling costs can be decreased when tape data capacity increases. Table 30 illustrates that the cartridge storage capacity of a 3490 subsystem is contrasted with available capacity improvements. As the compression ratio depends on dataset characteristics and the operating environment, three typical compression ratios (1:1, 2:1, and 3:1) are listed.
Table 30.
84 3590 Operator Guide
Chapter 8. Cartridge Care and Handling This chapter describes the care and handling of the IBM 3590 High Performance Cartridge Tape and Extended High Performance Cartridge Tape. Unpacking the Cartridges Unpack and inspect each cartridge to ensure that the leader block is correctly latched. If not, push the leader block toward the cartridge until it catches in the latch. Before you use the cartridges, condition them, for at least 24 hours, to the normal operating environment.
v Do not expose the tape cartridge to moisture or direct sunlight. v Do not expose recorded or blank cartridges to stray magnetic fields greater than 100 oersteds (such as those existing near high-current cables or power supplies). Such exposure can cause the loss of recorded data or make the blank cartridge unusable. Note: Do not attempt to degauss or ac bulk erase a tape cartridge. Degaussing makes the tape cartridge unusable.
There are two kinds of cartridge labels: A customer label and either a volume or a serial number label. Attach the customer label to the top surface of the cartridge. Then, attach the volume or serial number label to the side opposite the file-protect selector as shown in Figure 20 on page 86. Place the labels in the recessed cartridge label areas only. Labels that extend outside of the recess areas can cause loading problems in the drive, particularly when using the automatic cartridge facility.
v Do not load a damaged cartridge into a tape subsystem. During an emergency, if you need to recover data from a damaged cartridge, call your service representative. (IBM charges the customer for the time and materials that are used during the service call.) See Figure 21 to identify the parts of a cartridge that may become damaged. Figure 21. Cartridge Parts. The leader block 3 is shown unlatched with a length of tape 4 extending from the cartridge 1 for illustration purposes only.
v The tape (see item 4 ) was wound completely out of the cartridge (see item 1 ) onto the machine reel (not shown). It was then reattached to the cartridge reel (not shown) by the service representative. This repair is temporary and permits the cartridge to be loaded one time. This allows the data to be copied to a replacement cartridge. v The file-protect selector (see item 5 ) is damaged. v The braking mechanism (not shown) is jammed or broken. v The cartridge has other obvious damage.
Leader Block Replacement Figure 22 illustrates the replacement procedure. Figure 22. Leader Block Replacement Procedure The following lists the components required to replace the leader block: 1 3 5 7 9 Leader Block Clutch Tool Attachment Tool Cavity Attachment Tool Insertion Lever 2 4 6 8 Cartridge Guide Guide Groove Insert Pin Perform the following steps to replace the leader block when it has separated from the magnetic tape.
1. The replacement leader block must be an exact replacement for either the High Performance Cartridge Tape or the Extended High Performance Cartridge Tape. See Figure 19 on page 79. 2. Use care in aligning the tape leader, the insert, and the leader block to ensure proper loading of the repaired cartridge. 3. Never pull on the tape without using the brake release tool that is contained in the kit. Pulling on the tape with the brake engaged may damage the tape or brake mechanism in the cartridge.
Note: Use care to ensure that the tape is centered over the leader block. When the tape is centered over the leader block, there will be a 1.9 mm (0.075 inch) gap on both sides of the leader block. See Figure 23 on page 93. Failure to properly center the leader block on the tape will cause the repaired cartridge to fail. 7. Carefully close the insert guide 4 , and then place the insert pin 8 into the opening of the guide.
Leader Block Inspection A1400214 See Figure 23 to inspect the tape in the leader block. Figure 23. Leader Block Installment Procedure The following lists the components required for installation of the leader block: 1 Incorrectly Installed Tape on a Leader Block 2 3 4 5 Correctly Installed Tape on a Leader Block Incorrectly Installed Tape on a Leader Block Leader Block Insert Pin 6 Tape Figure 23 shows a correctly installed leader block in item 2 .
94 3590 Operator Guide
Chapter 9. Environmental and Shipping Information This chapter provides environmental, shipping, security, and disposal information for the 3590 tape cartridge. Operating and Storage Environment Operating Environment The 3590 tape cartridge operating environment, for tape subsystems, is as follows: v 15.6°C to 32.2°C (60°F to 90°F) dry bulb v 20 to 80 percent of relative humidity v 25.
Shipping Tape Media Cartridge Attention: It is imperative to package cartridges properly for shipment. Cartridges shipped with inadequate packaging could be damaged, which may result in a loss of recorded data. Adhere to the following packaging recommendations when shipping tapes off-site. To ship a cartridge, place it in a sealed, moisture-proof bag to protect the cartridge from moisture, contaminants, and physical damage.
Environment Unrecorded and packaged IBM cartridges can be exposed, for up to six days, to the following environment during shipment: v -23.3°C to 48.9°C (-10°F to 120°F) dry bulb v 5 to 80 percent of relative humidity v 26.7°C (80°F) maximum wet bulb. Recorded and packaged IBM cartridges can be exposed to the following environment, not to exceed 10 days, without risk of damage during shipment: v 4.4°C to 37.8°C (40°F to 100°F) dry bulb v 5 to 80 percent of relative humidity v 25.
98 3590 Operator Guide
Appendix A. Media/Hardware Problem Isolation An error code (FID FE) will be generated when the drive experiences an error and cannot determine if the error was caused by the tape cartridge or by a problem in the drive hardware. The FID FE is not displayed on the drive, but is logged in the sense information that is returned to the host system. Follow this procedure if you receive an error when reading or writing to the drive and there is no FID displayed.
Note: A repaired cartridge may be used long enough to recover data on that cartridge. When the data has been recovered, the cartridge should then be taken out of service and discarded or returned to the plant of origin. – If the cartridges look OK, and you have access to another 3590, try the operation with the suspect cartridges in another 3590. If your cartridges fail in the other 3590, replace the media. v Determine if the drive is bad. – Try a new tape on the suspect drive.
Appendix B. FID Messages Table 34 describes FID messages and customer action for the FID. A FID can be displayed on the drive panel or obtained from host software or error logs. See “Intervention Messages” on page 16 for an example of a FID on the drive panel. Table 34. FID Messages FID Description Customer Action 00-09 Configuration or Setup Problem Call for service 90-98 Drive Problem Call for service 1. Ensure you are using correct cartridge, 3590 only. 9A ACF or Cartridge Problem 2.
Table 34. FID Messages (continued) FID Description Customer Action 1. Ensure you are using correct cartridge, 3590 only. 2. This failure may be caused by a damaged cartridge. Before replacing any FRUs, inspect the cartridge that was being used when the error occurred for physical defects. Replace the cartridge if it is damaged. 9F ACF or Cartridge Problem 3. This failure may be caused by a dirty cartridge.
Table 34. FID Messages (continued) FID Description BD-C0 Drive Problem Call for service Customer Action C1 Drive or Power Problem This error may be caused by reduction of power or a power failure to the drive. If not a power failure, call for service. C2-C4 Drive Problem Call for service C5 Cartridge or Drive Problem C6 Drive Problem C7 Cartridge or Drive Problem C8-D2 Drive Problem D3 Cartridge or Drive Problem 1. Isolate between media and hardware. See “Appendix A.
Table 34. FID Messages (continued) FID Description Customer Action FID FF is always presented to the host in SCSI Request Sense Data. Some types of problems also present this FID on the operator panel. 1. FID FF Displayed on Drive Panel: (It also went to the host.) v FID FF is automatically displayed when the operator selects Force Error Dump from the operator Services menu. v Action: Remove the dump icon and the FID message by pressing the Reset Push button or by powering the drive OFF, and then ON.
Appendix C. Problem Determination SCSI Bus Devices on the SCSI bus must be varied off-line before the problem determination procedure can be performed. Due to the 3590 Ultra/Wide device speed, SCSI time-outs may occur to other peripherals if it is placed on a shared SCSI bus with multiple peripherals. To prevent this, both the Host Adapter SCSI address, and the 3590 Ultra SCSI address should be lower (0 or 1) then the SCSI addresses of the peripherals (E or F).
Inquiry Command 1. To check installed tape devices type the command Isdev -Cc tape. 2. Type tapeutil. 3. At the Enter Selection: prompt, select the Open a Device option and press Enter. 4. At the Enter the device special file name: prompt, type /dev/rmt1 or your actual device. 5. At the Select mode (1=Read/Write, 2=Read Only, 3=Write Only, 4=Append): prompt, type 1 to receive the Opening device... prompt. 6. At the Hit any key to continue... prompt, press Enter. 7.
13. At the Device closed... Hit any key to continue...: prompt, press enter. 14. At the Enter Selection: prompt, type q to stop the tapeutil program. AS/400 Environment Attachment Check Verify a 3590 is properly attached to an AS/400 with the following procedure. 1. Type WRKCFGSTS *DEV *TAP ASTLVL(*BASIC) at the prompt. 2. Type VFYTAP on the AS/400 command line. 3. Type the device associated with the 3590, such as TAP13. 4.
18. At the Enter megabytes to write: prompt, type 10. Data will be read from the tape and status will be displayed. 19. At the Enter Selection: prompt, select 24 to rewind the tape. 20. At the Enter Selection: prompt, select 2 to close the device. The Device closed response is displayed. 21. At the Enter Selection: prompt, select Q to exit the tapetest program. Sun Environment Attachment Check The devices must be fully installed and the host device drives must be configured and available.
20. At the Enter Selection: prompt, select 2 to close the device. The Device closed response is displayed. 21. At the Enter Selection: prompt, select Q to exit the tapetest program. Windows NT and Windows 2000 Environment Attachment Check The devices must be fully installed and the host device drives must be configured and available. For more information, see IBM SCSI Tape Drive, Medium Changer, and Library Device Drivers, GC35-0154. Perform the following commands: 1.
3. Ensure the Operator Fibre Channel address menu is set correctly. See options 4 and 5 in Table 3 on page 10. Use the Fibre address information to verify that: v The drive is receiving light over the Fibre cable (the address is not “-- ---”) v The drive can communicate over the Fibre cable (address is not “?? ?? ??”) v The drive AL_PA is not already being used on the Fibre loop (address = aa bb cc CONFLICT) v The drive AL_PA is not bypassed on the loop (address = aa bb cc OFFLINE).
Appendix D. Host Reporting Statistical Analysis and Reporting System The Statistical Analysis and Reporting System (SARS) assists in determining whether read and write errors are caused by the media (tape) or the hardware in the drive. The 3590 microcode contains a Volume SARS (VSARS) algorithm and a Hardware SARS (HSARS) algorithm to analyze errors. SARS algorithms report messages through SIMs and MIMs. Algorithms are executed in the 3590 just before a tape is unloaded.
You can select, depending on your software, the severities you wish to see. For example, you may only want to see the acute SIM/MIM, or prefer to see all SIMs and MIMs sent to the host. SIM/MIM filtering by severity can be done through configuration options. The four severity codes are listed below: v Severity 0 (FID4) code means the device requires service, but normal drive function is not affected. v Severity 1 (FID3) code means the problem is moderate.
CSM (formally ADSM) ANR8972E, ANR8830E, and ANR8831W messages AIX Error reports are available, the messages are dependent on the application HP Messages are dependant on the application SUN Messages are dependent on the application Windows NT Messages are dependent on the application Appendix D.
114 3590 Operator Guide
Notices This information was developed for products and services offered in the U.S.A. IBM may not offer the products, services, or features discussed in this document in other countries. Consult your local IBM representative for information on the products and services currently available in your area. Any reference to an IBM product, program, or service is not intended to state or imply that only that IBM product, program, or service may be used.
Any references in this information to non-IBM Web sites are provided for convenience only and do not in any manner serve as an endorsement of those Web sites. The materials at those Web sites are not part of the materials for this IBM product and use of those Web sites is at your own risk. IBM may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you Any performance data contained herein was determined in a controlled environment.
Trademarks The following terms are trademarks of the IBM Corporation in the United States or other countries or both: AIX ES/3090 ESCON FICON TotalStorage S/390 zSeries OS/400 pSeries TotalStorage MVS/ESA DFSMS/MVS VSE/ESA AS/400 ES/9000 IBM Magstar RS/6000 SP OS/390 iSeries xSeries System/370 IBMLink AIX/ESA VM/ESA The following terms are trademarks of other companies: HP-UX Sun Windows 2000 StorageTek Windows NT Microsoft, Windows NT, and Windows 2000 are registered trademarks of Microsoft Corporation
IBM Agreement for Licensed Internal Code You accept the terms of this Agreement by your initial use of a machine that contains IBM Licensed Internal Code (called “Code”). These terms apply to Code used by certain machines IBM or your reseller specifies (called “Specific Machines”). International Business Machines Corporation or one of its subsidiaries (“IBM”) owns copyrights in Code or has the right to license Code. IBM or a third party owns all copies of Code, including all copies made from them.
2. Reverse assemble, reverse compile, or otherwise translate the Code unless expressly permitted by applicable law without the possibility of contractual waiver; 3. Sublicense or assign the license for the Code; or 4. Lease the Code or any copy of it. AIX License Information Additional Terms and Conditions * * As pertaining to AIX code within the 3590 Model A00, A50, and A60 the following applies.
Compliance Laser Safety and Compliance These products contain components that comply with performance standards that are set by the U.S. Food and Drug Administration. This means that these products belong to a class of laser products that do not emit hazardous laser radiation. This classification was accomplished by providing the necessary protective housings and scanning safeguards to ensure that laser radiation is inaccessible during operation or is within Class 1 limits.
Canadian Department of Communications Compliance Statement This equipment does not exceed Class A limits per radio noise emissions for digital apparatus, set out in the Radio Interference Regulation of the Canadian Department of Communications.
Hinweis: Dieses Genehmigungsverfahren ist von der Deutschen Bundepost noch nicht veroöffentlicht worden. New Zealand Compliance Statement Attention: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Statement of Limited Warranty Part 1 – General Terms International Business Machines Corporation Armonk, New York, 10504 This Statement of Limited Warranty includes Part 1 - General Terms and Part 2 Country/region-unique Terms. The terms of Part 2 may replace or modify those of Part 1. The warranties provided by IBM in this Statement of Limited Warranty apply only to Machines you purchase for your use, and not for resale, from IBM or your reseller.
one that is at least functionally equivalent, you may return it to your place of purchase and your money will be refunded. The replacement may not be new, but will be in good working order. Extent of Warranty The warranty does not cover the repair or exchange of a Machine resulting from misuse, accident, modification, unsuitable physical or operating environment, improper maintenance by you, or failure caused by a product for which IBM is not responsible.
When warranty service involves the exchange of a Machine or part, the item IBM or your reseller replaces becomes its property and the replacement becomes yours. You represent that all removed items are genuine and unaltered. The replacement may not be new, but will be in good working order and at least functionally equivalent to the item replaced. The replacement assumes the warranty service status of the replaced item.
Production Status Each IBM Machine is manufactured from new parts, or new and used parts. In some cases, the Machine may not be new and may have been previously installed. Regardless of the Machine’s production status, IBM’s appropriate warranty terms apply. Limitation of Liability Circumstances may arise where, because of a default on IBM’s part or other liability, you are entitled to recover damages from IBM.
Extent of Warranty: The following replaces the first and second sentences of this Section: The warranty does not cover the repair or exchange of a Machine resulting from misuse, accident, modification, unsuitable physical or operating environment, operation in other than the Specified Operating Environment, improper maintenance by you, or failure caused by a product for which IBM is not responsible.
The terms of this Statement of Limited Warranty apply to Machines purchased from an IBM reseller. If you purchased this Machine from IBM, the terms and conditions of the applicable IBM agreement prevail over this warranty statement.
GERMANY: The IBM Warranty for Machines: The following replaces the first sentence of the first paragraph of this Section: The warranty for an IBM Machine covers the functionality of the Machine for its normal use and the Machine’s conformity to its Specifications. The following paragraphs are added to this Section: The minimum warranty period for Machines is six months.
Limitation of Liability: The following replaces items one and two of the first paragraph of this Section: 1. death or personal injury or physical damage to your real property solely caused by IBM’s negligence; and 2. the amount of any other actual direct damages, up to the greater of Irish Pounds 75,000 or 125 percent of the charges (if recurring, the 12 months’ charges apply) for the Machine that is the subject of the claim or which otherwise gives rise to the claim.
UNITED KINGDOM: Limitation of Liability: The following replaces items 1 and 2 of the first paragraph of this Section: 1. death or personal injury or physical damage to your real property solely caused by IBM’s negligence; 2.
132 3590 Operator Guide
Glossary This glossary defines the special terms, abbreviations, and acronyms that are used in this publication. If you do not find the term you are looking for, refer to the Dictionary of Computing, New York: McGraw-Hill, 1994. A ABEND. Abnormal end of task. access method. A technique for moving data between processor storage and input/output devices. ACS. Automated Cartridge System. allows the automatic feeding and loading of premounted tape cartridges requiring no operator action.
premounted tape cartridges or the manual loading of single tape cartridges. CCR. Channel command retry. channel. A device that connects the processing unit and main storage with the I/O control unit. channel command. An instruction that directs a data channel, control unit, or device to perform an operation or set of operations. command. A control signal that initiates an action or the beginning of a sequence of actions. contingent allegiance.
error-recovery procedures (ERP). (1) Procedures designed to help isolate and, where possible, to recover from errors in equipment. The procedures are often used in conjunction with programs that record the statistics of machine malfunctions. (2) Error-recovery procedures performed by the subsystem. explicitly activated. A process in which the attributes of an identifier are specified. Contrast with implicitly activated. extended contingent allegiance.
status at initial status time if the command is accepted and channel command retry is not requested. immediate mode. In tape-write-immediate mode, channel end and device end are presented separately. implicitly activated. A process in which the attributes of an identifier are determined by default. Contrast with explicitly activated. index. A function performed by the cartridge loader that moves cartridges down the input or output stack one cartridge position.
microcode. A code, representing the instructions of an instruction set, that is implemented in a part of storage that is not program-addressable. record. A collection of related data or words, treated as a unit; for example, in stock control, each invoice could constitute one record. microprocessor. An integrated circuit that accepts coded instructions for execution; the instructions may be entered, integrated, or stored internally. recording density.
T tape cartridge. A container holding magnetic tape that can be processed without separating it from the container. tape drive. A device that is used for moving magnetic tape and includes the mechanisms for writing and reading data to and from the tape. tape synchronous mode. The tape synchronous mode transfers records whose length is greater than the limits defined for buffered records. The device operates in the tape synchronous mode, if the format being processed is supported. tape unit.
Index Numerics 3494 library, cleaning drives in 68 3495 library, cleaning drives in 68 A accumulate mode, ACF 58 address device 5 set 33 address, device set address menu 77 AIX SCSI attachment check 105 AS/400 publications x SCSI attachment check 107 attention indicator LED flashing 77 steady on 77 Attention messages 20 automatic cartridge facility description 49 door and lock functions 54 functions 50 indicator LEDs 64 weight 53 automatic mode, using 60 B burning cartridges 97 C cartridge broken case 8
E environment considerations 85 disposing of cartridges 97 information 95 operating 85, 95 shipping 95, 96 storage 85, 95 environment, tape cartridge 95 Environmental Protection Agency 97 Environmental Protection Agency regulations 97 EPA regulations 97 erasing data 97 error code displayed 73 errors, read and write 85 extended high performance cartridge tape 128-track serpentine format 1 256-track serpentine format 1 read and write function 1 extended storage 95 F Fibre Channel address menu 40 problem dete
message action terms defined 19 Dvolser 16 FID1 17 FID2 18 FID3 18 FID4 19 intervention required 16 priorities 19 MIM definition 111 mode ACF, operation 55 modes of operation accumulate 58 automatic 60 manual mode 57 random 63 system 61 moisture, precaution 85, 97 Mount messages 20 N notices 115 notification, cleaning 69 O offline description 6 set 33 online description 6 set 33 operating environment disposing of cartridges 97 operating 95 shipping 95 storage 95 operating environment, tape cartridges 95 o
T tape cartridge tape 79 data capacity 79 file protect 80 position, indicator 14 recording format 79 restrictions 81 tape care 79, 85 tape cartridge broken case 87 burning 97 burning of 97 cannot insert 73, 85 case, broken 87 case, separated 87 case, unpacking and handling 85 cleaning 70 conditioning 85, 95 contamination 95 damage 85, 87 damaged 87 damaged cartridges 87 data security 97 disposal 97 disposing of 97 does not rewind, what to do 75 does not unload, what to do 75 environment 95 environments 95 e
Readers’ Comments — We’d Like to Hear from You IBM® TotalStorage Enterprise Tape System 3590 Operator Guide Publication No.
GA32-0330-13 _________________________________________________________________________________ Readers’ Comments — We’d Like to Hear from You Cut or Fold Along Line Fold and Tape Please do not staple Fold and Tape __________________________________________________________________________ NO POSTAGE NECESSARY IF MAILED IN THE UNITED STATES BUSINESS REPLY MAIL FIRST-CLASS MAIL PERMIT NO.
Part Number: 19P1593 GA32-0330-13 (1P) P/N: 19P1593 Printed in the United States of America on recycled paper containing 10% recovered post-consumer fiber.
Spine information: IBM® TotalStorage Enterprise Tape System 3590 3590 Operator Guide