HP StorageWorks SAN Switch installation guide Part number: AA-RWF3A-TE Fifth edition: May 2007
Legal and notice information © Copyright 2004-2007 Hewlett-Packard Development Company, L.P. © Copyright 2004-2007 Brocade Communications Systems, Incorporated Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
Contents About this guide . . . . . . . . . . . . . . . . . . . . Intended audience . . . . . . . Related documentation . . . . . Document conventions and symbols Rack stability . . . . . . . HP technical support . . . . . . HP authorized reseller . . . Helpful web sites . . . . . 1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SAN Switch ISL Trunking groups . . . . . . . . . . . . . . . . . . . . . . . . Optional SAN Switch features . . . . . . . . . . . . . . . . . . . . . . . . . SAN Switch optional port licenses and hardware . . . . . . . . . . . . . . . . . 2 Installing and configuring SAN Switches Shipping carton contents . . . . . . . . . . . . . . Installation and safety considerations . . . . . . . . . Electrical considerations . . . . . . . . . . . . Environmental considerations . . . . . . . . . .
4/32 SAN Switch nonport side LEDs 4/64 SAN Switch port side LEDs . . 4/64 SAN Switch nonport side LEDs 4/32B SAN Switch LEDs . . . . . POST and boot specifications . . . POST . . . . . . . . . . . Boot . . . . . . . . . . . . Interpreting POST results . . . . . Diagnostic tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BSMI notice . . . . . . . . . . . Japanese notice . . . . . . . . . Korean notices . . . . . . . . . Safety . . . . . . . . . . . . . . . Battery replacement notice . . . . Taiwan battery recycling notice . . Power cords . . . . . . . . . . . Japanese power cord statement . . Waste Electrical and Electronic Equipment English notice . . . . . . . . . . Dutch notice . . . . . . . . . . Czechoslovakian notice . . . . . . Estonian notice . . . . . . . . . Finnish notice . . . . . . . . . . French notice . . . .
Supported HBAs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 Glossary . . . . . . . . . . . . . . . . . . . . . . . . 147 Index . . . . . . . . . . . . . . . . . . . . . . . . .
Figures 1 4/8 and 4/16 SAN Switch port side . . . . . . . . . . . . . . . 2 4/32 SAN Switch port side . . . . . . . . . . . . . . . . . . . 3 4/32 SAN Switch nonport side . . . . . . . . . . . . . . . . . . 4 4/64 SAN Switch port side . . . . . . . . . . . . . . . . . . . 5 4/64 SAN Switch port numbering . . . . . . . . . . . . . . . . . 6 4/64 SAN Switch nonport side . . . . . . . . . . . . . . . . . . 7 4/32B SAN Switch port side . . . . . . . . . . . . . . . . . . . 8 4/32B SAN Switch FC ports . . . . .
Tables 1 Document conventions . . . . . . . . . . . . . . . . . . . . . 2 Optional port licenses and hardware kits . . . . . . . . . . . . . 3 SAN Switch shipping carton checklist . . . . . . . . . . . . . . 4 SAN Switch Rack Mount Kit hardware . . . . . . . . . . . . . . 5 Number of screws required to assemble the inner rails . . . . . . . 6 Time zone command values . . . . . . . . . . . . . . . . . . 7 Management tools . . . . . . . . . . . . . . . . . . . . . . 8 Example of a set of gateway addresses . .
About this guide This installation guide provides information to help you set up and configure the following HP switches: • • • • • HP HP HP HP HP StorageWorks StorageWorks StorageWorks StorageWorks StorageWorks 4/8 SAN Switch 4/16 SAN Switch SAN Switch 4/32 4/64 SAN Switch 4/32B SAN Switch “About this Guide” topics include: • • • • Intended audience, page 11 Related documentation, page 11 Document conventions and symbols, page 12 HP technical support, page 13 Intended audience This guide is intended
Document conventions and symbols This document follows the conventions in Table 1. Table 1 Document conventions Convention Element Medium blue text: Figure 1 Cross-reference links and e-mail addresses Medium blue underlined text (http:// www.hp.
Rack stability Rack stability protects personnel and equipment. WARNING! To • • • • • reduce the risk of personal injury or damage to the equipment, be sure that: The leveling jacks are extended to the floor. The full weight of the rack rests on the leveling jacks. In single rack installations, the stabilizing feet are attached to the rack. In multiple rack installations, the racks are coupled. Only one rack component is extended at any time.
HP authorized reseller For the name of your nearest HP-authorized reseller: • In the United States, call 1-800-345-1518. • Elsewhere, visit the HP web site: http://www.hp.com. Then click Contact HP to find locations and telephone numbers. Helpful web sites For third-party product information, see the following HP web sites: • • • • 14 http://www.hp.com http://www.hp.com/go/storage http://www.hp.com/support/ http://www.docs.hp.
1 Overview This chapter describes the following topics: • • • • • • • • 4/8 and 4/16 SAN Switch models, page 15 Enabling E_Ports on the 4/8 SAN Switch , page 18 4/32 SAN Switch models, page 20 4/64 SAN Switch models, page 24 4/32B SAN Switch models, page 29 SAN Switch ISL Trunking groups, page 31 Optional SAN Switch features, page 32 SAN Swtich optional kits, page 33 4/8 and 4/16 SAN Switch models The HP StorageWorks 4/8 SAN Switch and 4/16 SAN Switch models include: • HP StorageWorks 4/8 SAN Switch Base
4/8 and 4/16 SAN Switch features The 4/8 and 4/16 SAN Switches support link speeds of 1, 2, and 4 Gb/s. The switch operates in a fabric that contains multiple switches or as the only switch in a fabric. The 4/8 and 4/16 SAN Switches provide the following features: • Air-cooled 1U chassis.
4/8 and 4/16 SAN Switch chassis This section describes the chassis front (port side) and rear (nonport side). 4/8 and 4/16 SAN Switch port side All LEDs reside on the port side of the switch (see Figure 1). The 4/8 and 4/16 SAN Switch enclosure uses forced-air cooling, with the fans pushing the air from the nonport side of the chassis through the enclosure and exhausting at the port side. See Interpreting LED activity on page 69 for a complete description of switch LEDs.
3. Contact your HP representative to purchase the HP StorageWorks 4-Port Upgrade License, part number T4260A. 4. Upon receipt of the HP StorageWorks 4-Port Upgrade License, install the license: a. Log in to the 4/16 Switch as admin. b. Issue the licenseadd command, followed by the license key enclosed in quotation marks. (The license key consists of approximately 16 uppercase and lowercase letters and numerals.) NOTE: Enter the license key exactly as issued.
SAN Switch licensing SAN Switches operate differently in the network, depending on which HP StorageWorks domain licenses are installed. The 4/8 Base SAN Switch has no E_Port, unless you purchase and install the HP StorageWorks 4/8 Full Fabric Upgrade License. • Full Fabric license— Allows one or more switches to operate within a domain. All SAN Switch Power Pack models ship with this license installed.
4/32 SAN Switch models The HP StorageWorks 4/32 SAN Switch models include: • HP StorageWorks 4/32 SAN Switch Base ships with 16 ports activated and includes Zoning and Advanced Web Tools as standard software components. • HP StorageWorks 4/32 SAN Switch Full ships with 32 ports activated and includes Zoning and Advanced Web Tools as standard software components.
4/32 SAN Switch port side Figure 2 shows the port side of the 4/32 SAN Switch and identifies the components. ! IO IO I LN K SP D 1 scale: 1/8" = 1" 2 3 4 5 6 7 IOIOI ! LNK SPD 0 4 1 5 2 6 3 7 8 12 9 13 10 14 11 15 16 20 17 21 18 22 19 23 24 28 25 29 26 30 27 31 MRO25009a scale: 5/16" = 1" 1. Switch ID pull-out tab 2. Serial port 3. Ethernet port 4. FC ports 0–7 5. FC ports 8–15 6. FC ports 16–23 7.
4/32 SAN Switch nonport side Figure 3 shows the nonport side of the 4/32 SAN Switch, which contains the power supplies (including the AC power inlet and AC power switch) and fans. Scale: 1/8" = 1" 1 2 3 4 5 MRO25010a 1. Power supply 2 2. Fan 3 3. Fan 2 4. Fan 1 5.
NOTE: Check the port status to determine whether the license is preinstalled. Use the portshow command for ports 16 through 31. If the port status output indicates Started and Licensed, all 32 ports are activated. 1. If ports 16 through 31 show no license, you can purchase the HP StorageWorks 8-Port Upgrade License, part number T3677A, from an authorized HP representative. Your HP representative requires the 4/32 SAN Switch’s WWN in order to assign a license key.
4/64 SAN Switch models The HP StorageWorks 4/64 SAN Switch models include: • HP StorageWorks 4/64 SAN Switch Base ships with 32 ports activated and includes Zoning and Advanced Web Tools as standard software components. • HP StorageWorks 4/64 SAN Switch Full ships with 64 ports activated and includes Zoning and Advanced Web Tools as standard software components.
4/64 SAN Switch chassis This section provides an illustration of the front (port side) and rear (nonport side) of the SAN Switch chassis. 4/64 SAN Switch port side Figure 4 shows the port side and identifies the components.
Scale: 1/8" = 1" ! IO IO I 0 4 1 5 2 6 3 7 8 32 k rac 12 36 : for in.
4/64 SAN Switch port numbering Figure 5 identifies port numbering for the 4/64 SAN Switch.
Scale: 1/8" = 1" AT TE Ma N moximum TIO un tin screwN: g to be len 5m gth m for or rac 13 k /64 in. 1 2 3 4 5 6 Scale: 5/16" = 1" 25182a 1. Nonport side of switch 2. Power supply 2 3. Fan assembly 3 4. Fan assembly 2 5. Fan assembly 1 6. Power supply 1 Figure 6 4/64 SAN Switch nonport side Activating additional 4/64 SAN Switch ports The 4/64 SAN Switch contains 64 ports, with ports 0 through 31 enabled.
4/32B SAN Switch models The HP StorageWorks 4/32B SAN Switch models include: • HP StorageWorks 4/32B SAN Switch ships with 16 ports activated, and includes a Full Fabric license, Zoning and Advanced Web Tools as standard software components. • HP StorageWorks 4/32B Full SAN Switch ships with 32 ports activated, Full Fabric and includes Zoning and Advanced Web Tools as standard software components.
4/32B SAN Switch port side Figure 7 shows the port side of the 4/32B SAN Switch and identifies components. 1 2 3 5 4 1. Serial port 4. Power cord retainer 2. Ethernet or console port 5. Switch ID pull out tab 3.
Locating 4/32B SAN Switch FC ports FC ports are numbered from left to right, in eight-port groups, and are also numbered on the faceplate, see Figure 8. 25273a Figure 8 4/32B SAN Switch FC ports Activating additional 4/32B SAN Switch ports The 4/32B SAN Switch is available with either 16 ports (0 through 15) activated for the standard model or 32 ports (0 through 31) activated for the Full or Power Pack models.
NOTE: The maximum number of ports per trunk for the 4/8 and 4/16 SAN Switches is four. The FC ports are numbered from left to right in groups of four. This arrangement indicates the groups of ports that can be used in the same ISL trunking group. The trunking groups are the two or four sets of ports at the top or bottom of the group, as shown in Figure 5 on page 27.
SAN Switch optional port licenses and hardware Table 2 lists the optional port licenses and hardware kits available for SAN Switches.
NOTE: To obtain the latest information on hardware and software components, go to the B-Series section of the following web page: http://www.hp.com/go/san.
2 Installing and configuring SAN Switches This chapter describes the following topics: • • • • • • Shipping carton contents, page 35 Installation and safety considerations, page 38 Installing the switch as a stand-alone device, page 40 Installing the switch using the SAN Switch Rack Mount Kit, page 41 Cabling and configuring the SAN Switch, page 52 Connecting the SAN Switch to the fabric, page 53 Shipping carton contents Figure 9 and Table 3 identify shipping carton contents for a typical SAN Switch.
Table 3 identifies the carton contents included with your SAN Switch. Table 3 SAN Switch shipping carton checklist 36 Number Description 1 One SAN Switch Accessories Box containing: • One 3.
Number Description • • • • One One One One HP HP HP HP StorageWorks StorageWorks StorageWorks StorageWorks 4/16 SAN Switch 4/32 SAN Switch 4/32B SAN Switch 4/64 SAN Switch SAN Switch installation guide 37
Installation and safety considerations Install the switch using one of the following methods: • As a stand-alone unit on a flat surface. See Installing the switch as a stand-alone device on page 40. • HP highly recommends mounting the switch in one of the following HP customized racks: • HP System/e Rack • HP 10000 G2 Series Rack, HP 9000 Series Rack and HP 10000 Series Rack See Installing the switch using the SAN Switch Rack Mount Kit on page 41 for detailed instructions.
IMPORTANT: The 40 ºC value applies to the ambient air temperature at the air intake vents on the nonport side of the switch. The temperature inside the switch can be up to 80 ºC (176 ºF) during switch operation. If the internal temperature range exceeds the operating ranges of the components, the LEDs, error messages, and Fabric Watch alerts indicate a problem. Enter the tempshow or Fabric Watch command to view temperature status.
• Ensure that the ambient air temperature does not exceed 40 ºC (104 ºF) while the switch is operating. NOTE: Do not block air vents. The switch uses ambient air for cooling. Installing the switch as a stand-alone device To install the switch as a stand-alone unit: 1. Unpack the switch and verify that all items listed in Shipping carton contents on page 35 are present. 2. Locate the four rubber feet in the accessory box. 3. Apply the adhesive rubber feet to the switch.
Installing the switch using the SAN Switch Rack Mount Kit This section provides instructions for installing the SAN Switch in the following HP custom racks: • HP System/e Rack • HP 10000 G2 Series rack, HP 9000 and HP 10000 Series racks For optimal cable management, HP recommends that you install the SAN Switch Rack Mount Kit to allow the nonport side of the switch to slide out of the cool-air side of the rack. In this installation, the port side of the switch is set 12.
Table 4 SAN Switch Rack Mount Kit hardware Item Description Two rear mounting brackets A right inner rail and a right outer rail A left inner rail and a left outer rail 14 #8-32 x 3/16-inch Phillips pan-head screws with thread lock for use with the SAN Switch 2/32 only.
CAUTION: For proper airflow, the SFP media side of the SAN Switch must face the rear of the rack. To install the switch in a rack: 1. Verify that the required parts and hardware are available. See Table 3 on page 36. 2. Choose a mounting location for the switch in the rack. 3.
4. Assemble the outer rails by completing option a or option b: a. Attach the left outer rail and the right outer rail to the rear mounting brackets using two 1/4-20 hex nuts with captive star lock-washers attached loosely, as shown in Figure 12. Do not tighten the nuts until completing the steps in Securing the switch to the outer rails, page 50.
b. Depending on the rack you are using, complete one of the following tasks: • For HP 10000 series racks, install two #10-32 x 1/2-inch Phillips pan-head screws with captive star lock-washers and two #10 adapter washers in the upper and lower hole locations of the right rail. Then install two #10-32 x 1/2-inch Phillips pan-head screws with captive star lock-washers and two #10 adapter washers in the upper and lower hole locations of the left rail. See Figure 13.
Figure 14 Assembling the outer rails (HP System/e Rack) 5. Depending on the device model, the SAN Switch Rack Mount Kit requires different screw types for securing the inner rails. Use Table 5 to determine the number and screw type for your specific switch. CAUTION: Do not use any screws other than those provided. Using longer screws than those provided can cause damage to internal components.
6. Identify the screw holes to be used on the inner rails designed for the switch: • To attach the inner rails to the SAN Switch 2/32 use the screw holes marked 32. • To attach the inner rails to the 4/8, /16 and 4/32B SAN Switches, use five screw holes marked 8, and the plenum requires one screw hole marked 8 and one screw hole marked 16, as shown in Figure 15 on page 48. • To attach the inner rails to the 4/32 or 4/64 SAN Switch, use the screw holes marked 16, as shown in Figure 16 on page 48. 7.
8. If you are installing the 4/8, 4/16 or 4/32B SAN Switch, verify that a plenum (an air duct that attaches to the switch rails, enabling the switch to draw cooler air into the switch from outside the rack, rather than drawing in heated air from within the rack.) is preinstalled, as shown in Figure 15. If not installed, see Installing the Plenum (if required), page 49 to install a plenum on the 4/8, 4/16 or 4/32B SAN Switch.
Installing the Plenum (if required) If installing one of the following SAN switches only, you must install the plenum that ships in the accessory kit with the rack mount hardware: • 4/8 SAN Switch • 4/16 SAN Switch • 4/32B SAN Switch To install the plenum: 1. Place the device (with inner rails attached) on a flat surface, see Figure 17. 2. Obtain the plenum and four 8-32 x .312 Phillips Pan-head SEMs screws from the accessory kit. 3.
NOTE: Figure 17 illustrates how to attach the plenum to the 4/8 or 4/16 SAN Switch specifically. If installing the plenum on the 4/32B SAN Switch, the procedure and figure also applies. 1 2 ! 3 AT TE Ma NT IO mo xim N: unt um ing scr to ew be len 5m gth m for or 13/ rack 64 in. OI IOI 25052a Figure 17 Attaching the Plenum to the 4/8 or 4/16 SAN Switch 1. Plenum 2. SAN Switch 3.
Figure 18 Securing the switch (in HP 9000 Series or HP 10000 Series Racks) Figure 19 Securing the switch (in an HP System/e rack) 3. Tighten the hex nuts installed earlier. See step 4a, page 44. NOTE: To uninstall a switch, remove the middle #10-32 x 1/2-inch Phillips pan-head screw with captive star lock-washer from either side of the rack uprights. This completes the rack mount procedure.
Cabling and configuring the SAN Switch The SAN Switch must be configured to ensure correct operation with a network and fabric. For instructions on configuring the switch to operate in a fabric containing switches from other vendors, see the Fabric OS administrator’s guide. For more information about the commands used in this procedure, see the Fabric OS command reference manual for the Fabric OS version running on your switch.
Connecting the SAN Switch to the fabric Connecting the SAN Switch to the fabric involves the following steps: 1. Obtain required items on page 53 2. Make a serial connection on page 53 3. Apply power to the switch and log in on page 56 4. Set the IP address on page 57 5. Create an Ethernet connection on page 58 6. Modify the FC domain ID (optional) on page 58 7. Install the SFP transceivers on page 59 8. Connect the cables on page 60 9. Verify the configuration on page 60 10.
NOTE: If the serial port on the workstation uses an RJ-45 connector instead of an RS-232 connector, remove the adapter on the end of the serial cable and insert the exposed RJ-45 connector into the RJ-45 serial port on the workstation. IO IO I ! ck .
NOTE: Figure 20 shows the 4/16 SAN Switch; however, this procedure is similar for all SAN Switches. 3. Close any serial communication programs running on the workstation. 4.
Apply power to the switch and log in Once a serial connection is established, apply power to the switch: 1. Connect the power cord to a power inlet on the switch and a power source, as shown in Figure 21. NOTE: The 4/32, 4/32B and 4/64 SAN Switch models use two power cords. The 4/8 and 4/16 SAN Switches use one power cord. IO IO I ! ck .
4. When the terminal emulator application, which uses a serial connection, stops reporting information, press Enter to display the login prompt. 5. Log in using the administrative account; the logon is admin and the default password is password. Create up to two simultaneous admin sessions and four user sessions. For more details, see the Fabric OS administrator’s guide and the Fabric OS command reference manual for the Fabric OS running on your switch.
Create an Ethernet connection To create an Ethernet connection: 1. Connect an Ethernet cable to the Ethernet port and to the workstation, or to an Ethernet network containing the workstation, as shown in Figure 22 on page 58. NOTE: Figure 22 shows the 4/16 SAN Switch; however, this procedure is similar for all SAN Switches. IO IO I ! ck .
3. At the Fabric Parameters prompt, enter y and press Enter: Fabric Parameters (yes, y, no, n): (no) y 4. Enter a unique domain ID, such as the domain ID used by the previous switch, if it is still available: Domain: (1..239) [1] 3 5. Respond to the remaining prompts or press Ctrl+D to accept the default settings. 6. Issue the switchenable command to re-enable the switch. 7. Optional: Specify any custom status policies: a. Issue the switchstatuspolicyset command.
Connect the cables CAUTION: The minimum bend radius for a 50-micron cable is 2 inches under full tensile load and 1.2 inches with no tensile load. Because they are easily overtightened, HP does not recommend tie wraps for optical cables. To connect the cables to the SFP transceivers: 1. The cable connectors are keyed to ensure correct orientation.
Set the switch date and time The date and time switch settings are used for logging events. Switch operation does not depend on the date and time; a switch with an incorrect date and time value still functions properly. You can synchronize the local time of the principal or primary Fabric Configuration Server (FCS) switch with that of an external Network Time Protocol (NTP) server. To set the date and time for a switch (see Example 2 following the procedure): 1. Log in to the switch as admin. 2.
Example 3: switch:admin> tsclockserver LOCL switch:admin> tsclockserver 132.163.135.131 switch:admin> Set the time zone To set the time zone: 1. Log in as admin. 2. Issue the following tstimezone command: tstimezone[houroffset] [minuteoffset] • • • • For For For For Pacific Standard Time, enter tstimezone –8,0. Mountain Standard Time, enter tstimezone –7,0. Central Standard Time, enter tstimezone –6,0. Eastern Standard Time, enter tstimezone –5,0.
Table 6 Time zone command values Local time tstimezone parameter Atlantic Standard –4,0 Atlantic Daylight –3,0 Eastern Standard –5,0 Eastern Daylight –4,0 Central Standard –6,0 Central Daylight –5,0 Mountain Standard –7,0 Mountain Daylight –6,0 Pacific Standard –8,0 Pacific Daylight –7,0 Alaskan Standard –9,0 Alaskan Daylight –8,0 Hawaiian Standard –10,0 SAN Switch installation guide 63
Installing and configuring SAN Switches
3 Managing SAN Switches This chapter describes the following topics: • • • • • • • • • • • • • • Powering on and off, page 66 SAN Switch management features, page 67 Managing SAN Switches from a single management station, page 67 Interpreting LED activity, page 69 4/8 and 4/16 SAN Switch LEDs, page 69 4/8 and 4/16 SAN Switch LED patterns, page 70 4/32 SAN Switch port side LEDs, page 74 4/32 SAN Switch nonport side LEDs, page 78 4/64 SAN Switch port side LEDs, page 79 4/64 SAN Switch nonport side LEDs, page
Powering on and off The following sections provide information on powering specific SAN Switch models on and off. 4/8 and 4/16 SAN Switch models To power on: 1. Connect one end of the power cord to the AC inlet on the switch; connect the other end to a power source. 2. Set the AC power switch to I. The switch runs POST each time it is powered on, reset, or rebooted. POST requires approximately three minutes. To power off: 1. Set the AC power switch to O. 2. Remove the power cords from the power sources.
SAN Switch management features SAN Switches use built-in management tools to help you monitor fabric topology, check port status, and debug the switch. Table 7 lists the management tools available. When running IP over FC, these management tools must be supported by both HBA and HBA drivers. For a list of supported HBAs, see the HP StorageWorks SAN design guide: http://www.hp.com/go/sandesignguide.
Table 8 Example of a set of gateway addresses 68 Connection type Management station 1st switch 2nd switch 3rd switch Ethernet 192.168.1.099 192.168.1.10 204.1.1.11 204.1.1.12 FCIP 192.168.65.09 192.168.65.10 192.168.65.11 192.168.65.12 Gateway 192.168.1.10 Any, but itself 192.168.1.10 192.168.1.
Interpreting LED activity System activity and status can be determined through the LEDs on the switch. There are three possible LED states that display either green or amber: • A steady light • A flashing light • No light LEDs display either green or amber colors. A steady green light indicates a healthy state. Sometimes, the LEDs flash any of the colors during boot, POST, or other diagnostic tests.
4/8 and 4/16 SAN Switch LED patterns Table 9 and Table 10 on page 71 summarize LED locations, colors, and recommended actions. Power Status LED patterns The system and power LED patterns are described in Table 9. Table 9 4/8 and 4/16 SAN Switch LED patterns 70 LED name LED color Hardware status Recommended action Power Status LED No light Switch is off or power supply failed. Verify that switch is on and has completed booting. Steady green Switch is on and power supply is functioning properly.
4/8 and 4/16 SAN Switch system Status LED patterns The system status LED patterns are described in Table 10. Table 10 System status LED patterns during normal operation LED name LED color Hardware status Recommended action System Status LED No light Switch is off, boot is not complete, or boot failed. Verify that switch is on and has completed booting. Steady green Switch is operational. No action required.
4/8 and 4/16 SAN Switch port LED patterns Each port includes two LEDs: a Port Speed indicator and a Port Status indicator. Table 11 describes the LED locations, colors, and recommended actions. Table 11 Port LED patterns during normal operation 72 LED name LED color Hardware status Recommended action Port Status No light No power or signal carrier (SFP or cable) detected. Check SFP and cable. Steady green Port is online (connected to external device) but has no traffic. No action required.
LED name LED color Hardware status Recommended action Port Speed Steady green, amber off Port is transmitting or receiving at 2 Gb/s. No action required. Green off, amber off Port is transmitting or receiving at 1 Gb/s. No action required. Green off, steady amber Port is transmitting or receiving at 4 Gb/s. No action required.
4/8 and 4/16 SAN Switch Ethernet LED patterns Each Ethernet port has two LEDs described in Table 12. Table 12 Ethernet LED patterns LED name LED color Hardware status Recommended action Ethernet Speed No light Port speed is 10 Mb/s. No action required. Steady green Port speed is 100 Mb/s. No action required. Steady amber Link is valid. No action required. Blinking amber Traffic is flowing. No action required.
IOIOI ! LNK SPD 0 4 1 5 2 6 3 7 8 12 9 13 10 14 11 15 16 20 17 21 18 22 19 23 24 28 25 29 26 30 27 31 scale: 5/16" = 1" 1 3 2 IOIOI ! LNK SPD 0 4 4 5 6 1 5 2 6 7 3 7 8 MRO25012a 1. System Status LED 2. Link LED 3. Top port LEDs (0 through 3) 4. Power Status LED 5. Speed LED 6. Port Status LEDs 7. Port Speed LEDs 8.
Table 13 describes the 4/32 SAN Switch port side LEDs. Table 13 4/32 SAN Switch port side LED patterns LED name LED color Hardware status Recommended action Power Status No light Switch is off or there is an internal power supply failure. Verify that the system is on. If the system is on, the unit is faulty. Contact HP Technical Support. Steady green Switch is on and power supplies are functioning properly. No action required. No light System is off, boot is not complete, or boot failed.
LED name LED color Hardware status Recommended action Port Status No light No signal or light carrier (media or cable) detected. Check the transceiver and cable. Slow-flashing green (flashing in two-second intervals) Port is online but segmented because of a loopback cable or incompatible switch connection. No action required. Fast-flashing green (flashing in half-second intervals) Port is online and an internal loopback diagnostic test is running. No action required.
4/32 SAN Switch nonport side LEDs The 4/32 SAN Switch has the following nonport side LEDs: • Two Power Supply LEDs • Three Fan Status LEDs Figure 25 shows the locations of the nonport side LEDs. 1 2 3 4 5 MRO25013a 1. Power Supply 2 status LED 2. Power Supply 1 Status LED 3. Fan 3 Status LED 4. Fan 2 Status LED 5.
Table 14 describes the 4/32 SAN Switch nonport side LEDs. Table 14 4/32 SAN Switch nonport side LED patterns LED name LED color Hardware status Recommended action Power Supply Status No light Power supply is not receiving power or power is off. Verify that the power supply is on and seated and the power cord is connected to a functioning power source. Steady green Power supply is operating normally. No action required.
Scale: 1/4" = 1" 0 4 1 5 2 6 3 7 8 12 9 13 10 14 11 15 16 20 17 21 18 22 19 23 24 28 25 29 26 30 27 31 32 36 33 37 34 38 35 39 40 44 41 45 42 46 43 47 48 52 49 53 50 54 51 55 56 60 57 61 58 62 59 63 IOIOI ! 1 4 7 9 8 0 4 1 5 2 6 3 7 32 36 33 37 34 38 35 39 IOIOI ! 2 3 5 6 10 11 12 25183a 1. System Status LED 2. System Power LED 3. Serial port 4. Ethernet port 5. Ethernet Speed LED 6. Ethernet Link LED 7.
Table 15 4/64 SAN Switch port side LED patterns LED name LED color Hardware status Recommended action Power Status No light Switch is off or there is an internal power supply failure. Verify that the system is on (both power switches set to “1”), the power cables are attached, and the power source is live. If the system is on, the unit may be faulty. Contact HP Technical Support. Steady green Switch is on and power supplies are functioning properly. No action required.
LED name LED color Hardware status Recommended action Port Status No light No signal or light carrier (media or cable) detected. Check the transceiver and cable. Slow-flashing green (flashing in two-second intervals) Port is online but segmented because of a loopback cable or incompatible switch connection. No action required. Fast-flashing green (flashing in half-second intervals) Port is online and an internal loopback diagnostic test is running. No action required.
1 2 3 4 6 5 7 Scale: 5/16" = 1" 8 9 10 25184a 1. Power Supply 2 Status LED 2. Power supply 2 3. Fan assembly 3 4. Fan assembly 2 5. Fan assembly 1 6. Power Supply 1 Status LED 7. Power supply 1 8. Fan Assembly 3 Status LED 9. Fan Assembly 2 Status LED 10.
Table 16 4/64 SAN Switch nonport side LED patterns during normal operation LED name LED color Hardware status Recommended action Power Supply Status No light Power supply is not receiving power or power is off. Verify that the power supply is on and seated and the power cord is connected to a functioning power source. Steady green Power supply is operating normally. No action required.
4/32B SAN Switch LEDs The 4/32B SAN Switch model integrates the following LEDs: • • • • System Status LED Power Status LED Port Status LEDs (32), one for each FC port, located directly above the ports Power Supply status LED on each power supply FRU, in the upper right corner Figure 28 and Table 17 identify the port side LEDs. 1 2 4 3 25274a 1. System Status LED 2. Port Status LED 3. System Power LED 4.
LED name LED color Hardware status Recommended action System Status No light System is off, boot is not complete, or boot failed. Verify that the system is on and booting is complete. Steady green System is on and power supplies are functioning properly. No action required. Steady Amber (for more than 5 seconds) Boot failed and system is faulty. Perform the following steps: 1. Connect a serial cable to the system. 2. Reboot the system. 3. Check the failure indicated on the system console. 4.
LED name LED color Hardware status Recommended action Port Status No light No signal or light carrier (media or cable) detected. Check the transceiver and cable. Slow flashing green (flashing in two-second intervals) Port is online but segmented because of a loopback cable or incompatible switch connection. No action required. Fast flashing green (flashing in half-second intervals) Port is online and an internal loopback diagnostic test is running. No action required.
POST and boot specifications When the switch is powered on or rebooted, the switch performs POST. Total boot time with POST is at least three minutes. Use fastboot to bypass POST after subsequent reboots. For more information about the fastboot command, refer to the Fabric OS command reference manual for the Fabric OS version running on your switch. POST POST is a system check that is performed each time the switch is powered on, rebooted, or reset. During POST, the LEDs flash different colors.
Interpreting POST results To determine whether POST completed successfully and whether any errors were detected: 1. Verify that the switch LEDs indicate that all components are healthy.
Managing SAN Switches
4 Installing field-replaceable units The 4/8 and 4/16 SAN Switches do not require regular maintenance and do not contain any FRUs; these switches are themselves FRUs. The 4/32 SAN Switch and 4/64 SAN Switches contain two FRUs: the power supply and the fan assembly.
Scale: 1/8" = 1" 1 2 3 4 MRO25014a 1. Power Supply 2 Status LED 2. Power supply 2 3. Power Supply 1 Status LED 4. Power supply 1 Figure 29 4/32 SAN Switch power supplies on the nonport side CAUTION: Disassembling any part of the power supply voids the part warranty and regulatory certifications. There are no user-serviceable parts inside the power supply. Table 18 describes the Power Supply Status LEDs and corrective actions.
Table 18 4/32 SAN Switch Power Supply Status LEDs LED color Meaning Corrective action No light The power supply is not receiving power or is off. Verify that the power supply is on and seated and that the power cord is connected to a functioning power source. Steady green Power supply is operating normally. No action required. Steady amber for more than 5 seconds Power supply fault for one of the following reasons: Power cable is disconnected. Power supply is off. Power supply has failed.
Procedure To replace a power supply in the 4/32 SAN Switch, see Figure 30 on page 94: 1. If the switch will remain powered on, verify that the functioning power supply (the one not being replaced) has been powered on for at least four seconds and displays a green LED. 2. If the power supply you are replacing is not already powered off, press the AC power switch to power it off. 3. Unplug the power cord from the power supply you are replacing. 4.
CAUTION: Do not force the installation. If the power supply does not slide in easily, make sure that it is oriented correctly before continuing. 8. Secure the power supply to the chassis by tightening the captive screw. 9. Plug the power cord into the power supply and then press the AC power switch to turn it on. 10. Verify that the LED on the new power supply displays a steady green light while the switch is operating (see Table 18 on page 93).
Replacing the 4/32 SAN Switch fan assembly The 4/32 SAN Switch contains three fan assemblies, as shown in Figure 31. Fabric OS identifies the fans from left to right as Fan 3, Fan 2, and Fan 1. Scale: 1/8" = 1" 1 2 3 MRO25016a 1. Fan assembly 3 2. Fan assembly 2 3. Fan assembly 1 Figure 31 4/32 SAN Switch fan assemblies on the nonport side Table 19 describes the Fan Status LEDs and provides corrective actions.
Table 19 4/32 SAN Switch Fan Status LED behavior LED color Meaning Corrective action No light Fan assembly is not receiving power. Verify that the fan assembly is seated in the switch. Steady green Fan assembly is operating normally. No action required. Steady amber for more than 5 seconds Fan fault for one of the following reasons: One or more of the fans in the fan assembly has failed. The fan FRU was disabled by the user. Verify that the fan FRU is enabled.
Scale: 1/4" = 1" 2 1 MRO25017a 1. Fan assembly 2. Captive screw Figure 32 Installing the fan assembly in a 4/32 SAN Switch CAUTION: Do not force the installation. If the fan assembly does not slide in easily, make sure that it is oriented correctly before continuing. 6. Verify that the Fan Status LED does not display a steady amber light for more than five seconds, which indicates a fault (see Table 19 on page 97).
Replacing the 4/64 SAN Switch power supply The 4/64 SAN Switch uses two power supplies, as shown in Figure 33. The Fabric OS identifies the power supplies from right to left on the nonport side as Power Supply #1 (on the right) and Power Supply #2 (on the left). IMPORTANT: Operate the switch with both power supplies to maintain redundancy. Scale: 1/8" = 1" 2 1 3 Scale: 5/16" = 1" 25187a 1. Power supply 2 2. Nonport side of switch 3.
Items required Replacing a 4/64 SAN Switch power supply should take less than two minutes and requires the following items: • New power supply • Phillips #1 screwdriver 100 Installing field-replaceable units
Procedure To replace a power supply in the 4/64 SAN Switch: 1. If the switch will remain powered on, verify that the functioning power supply (the one not being replaced) has been powered on for at least four seconds and displays a green LED. 2. If the power supply you are replacing is not already powered off, press the AC power switch to power it off. See Figure 34 for the location of the AC power switch and a list of power supply components. 3.
scale: 1/4" = 1" 7 scale: 1/4" = 1" 8 1 2 3 4 9 Scale: 3/8" = 1" 5 6 25188a 1. AC power receptacle 2. Status LED 3. Handle (inset) 4. Captive screw (inset) 5. AC power switch 6. Power supply 7. Power supply 8. Captive screw 9. Handle Figure 34 Installing the power supply in the 4/64 SAN Switch CAUTION: Do not force the installation. If the power supply does not slide in easily, make sure that it is correctly oriented before continuing. 8.
10. Verify that the LED on the new power supply displays a steady green light while the switch is operating (see Table 18 on page 93). If the LED is not green, make sure that the power supply is firmly seated. Fabric OS identifies the power supplies in a 4/64 SAN Switch from left to right as PS2 and PS1, as shown in Figure 34 on page 102. Replacing the 4/64 SAN Switch fan assembly The 4/64 SAN Switch contains three fan assemblies, as shown in Figure 35.
Table 20 describes the Fan Status LEDs and provides corrective actions. Table 20 Fan Status LEDs LED color Meaning Corrective action No light Fan assembly is not receiving power. Verify that the fan assembly is seated in the switch. Steady green Fan assembly is operating normally. No action required. Steady amber for more than 5 seconds Fan fault for one of the following reasons: One or more of the fans in the fan assembly has failed. The fan FRU was disabled by the user.
1 scale: 1/4" = 1" Scale: 3/8" = 1" 2 3 4 5 6 25186a 1. Fan assembly unit 2. Captive screw 3. Fan Status LED 4. Handle 5. Fan assembly unit 6. Captive screw Figure 36 Inserting the fan assembly in a 4/64 SAN Switch CAUTION: Do not force the installation. If the fan assembly does not slide in easily, make sure that it is oriented correctly before continuing. 6.
Replacing the 4/32B SAN Switch Power Supply/Fan Assembly Unit Read this section for Power Supply/Fan Assembly Unit replacement procedures. Power Supply/Fan Assembly overview The 4/32B SAN Switch fans are fixed inside the integrated power supply/fan FRU to provide necessary airflow to cool the whole system. There is one fan located in the rear section of each FRU. The system software sets fan speed and measures their speeds through the tachometer interface.
CAUTION: Disassembling any part of the fan assembly voids the part warranty and regulatory certifications. There are no user-serviceable ports inside the Power Supply/Fan Assembly Unit. Because the cooling system relies on pressurized air, do not leave any of the fan assembly slots empty longer than two minutes while the switch is operating. If a fan assembly fails, leave it installed in the switch until it can be replaced.
LED name LED color and behavior Description Action required failure, a fan failure, or one or more environmental ranges has exceeded. Technical Support. How to determine to replace the Power Supply/Fan Assembly Unit Verifying if the Power Supply requires replacing: • Check the Power Supply status LED next to the I/O switch. If the Power Supply status LED is not on, verify that the Power Supply is on and seated and the power cord is connected to a functioning power source.
Items required Replacing a 4/32B SAN Switch Power Supply/Fan Assembly Unit takes approximately two minutes, and requires the following items: • 4/32B SAN Switch • New Power Supply/Fan Assembly Unit • Phillips #1 screwdriver Procedure To replace an existing Power Supply/Fan Assembly Unit: WARNING! The 4/32B SAN Switch utilizes two power cords. Be aware that with the removal of a single power cord and power supply/fan assembly unit, power is still present in the switch. 1.
7. Install the new Power Supply/Fan Assembly Unit in the chassis: a. Orient the Power Supply/Fan Assembly Unit as shown in Figure 38, with the captive screw on the right. 25276a Figure 38 Inserting the Power Supply/Fan Assembly Unit in the 4/32B SAN Switch b. Gently push the power supply into the chassis until it is seated. CAUTION: Do not force the installation. Verify that the unit is oriented correctly before continuing. c.
CAUTION: If the SFP you does not have a bale, use a small implement, such as a screwdriver, to press and release the trigger beneath the port. Non-baled SFPs can be damaged by the removal process and are not recommended. See SAN Swtich optional kits on page 33 for a list of supported SFPs. 5. Repeat this procedure for the remaining ports, as required. To install a replacement SFP: 1. Make sure that the bale is in the unlocked position, and then place the SFP in the correctly oriented position on the port.
A IO IO I ! 1 2 scale: 1/2" = 1" IO IO I B ! MRO25020a 1. Bale Figure 39 Installing the SFP 112 Installing field-replaceable units 2.
A Regulatory compliance and safety Regulatory compliance Federal Communications Commission notice for Class A equipment This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hewlett-Packard Company my void the user’s authority to operate the equipment. Cables Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods in order to maintain compliance with FCC Rules and Regulations.
Certification and classification information This product contains a laser internal to the fiber optic (FO) transceiver for connection to the Fibre Channel communications port. In the USA, the FO transceiver is certified as a Class 1 laser product conforming to the requirements contained in the Department of Health and Human Services (DHHS) regulation 21 CFR, Subchapter J. A label on the plastic FO transceiver housing indicates the certification.
European Union notice Products bearing the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community and if this product has telecommunication functionality, the R&TTE Directive (1995/5/EC).
Japanese notice Korean notices SAN Switch installation guide 117
Safety Battery replacement notice Your switch is equipped with a lithium manganese dioxide, a vanadium pentoxide, or an alkaline internal battery or battery pack. There is a danger of explosion and risk of personal injury if the battery is incorrectly replaced or mistreated. Replacement is to be done by an HP authorized service provider using the HP spare part designated for this product. For more information about battery replacement or proper disposal, contact an HP authorized service provider.
Taiwan battery recycling notice The Taiwan EPA requires dry battery manufacturing or importing firms in accordance with Article 15 of the Waste Disposal Act to indicate the recovery marks on the batteries used in sales, givaway, or promotion. Contact a qualified Taiwanese recycler for proper battery disposal. Power cords The power cord set must meet the requirements for use in the country where the product was purchased.
Waste Electrical and Electronic Equipment directive English notice Disposal of waste equipment by users in private households in the European Union This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for recycling of waste electrical and electronic equipment.
Czechoslovakian notice Likvidace zař ízení soukromými domácími uživateli v Evropské unii Tento symbol na produktu nebo balení označ uje výrobek, který nesmí být vyhozen spolu s ostatním domácím odpadem. Povinností uživatele je př edat takto označ ený odpad na př edem urč ené sběrné místo pro recyklaci elektrických a elektronických zař ízení. Okamžité tř ídění a recyklace odpadu pomůže uchovat př írodní prostř edí a zajistí takový způsob recyklace, který ochrání zdraví a životní prostř edí č lověka.
Finnish notice Laitteiden hävittäminen kotitalouksissa Euroopan unionin alueella Jos tuotteessa tai sen pakkauksessa on tämä merkki, tuotetta ei saa hävittää kotitalousjätteiden mukana. Tällöin hävitettävä laite on toimitettava sähkölaitteiden ja elektronisten laitteiden kierrätyspisteeseen. Hävitettävien laitteiden erillinen käsittely ja kierrätys auttavat säästämään luonnonvaroja ja varmistamaan, että laite kierrätetään tavalla, joka estää terveyshaitat ja suojelee luontoa.
German notice Entsorgung von Altgeräten aus privaten Haushalten in der EU Das Symbol auf dem Produkt oder seiner Verpackung weist darauf hin, dass das Produkt nicht über den normalen Hausmüll entsorgt werden darf. Benutzer sind verpflichtet, die Altgeräte an einer Rücknahmestelle für Elektro- und Elektronik-Altgeräte abzugeben.
Hungarian notice Készülékek magánháztartásban történő selejtezése az Európai Unió területén A készüléken, illetve a készülék csomagolásán látható azonos szimbólum annak jelzésére szolgál, hogy a készülék a selejtezés során az egyéb háztartási hulladéktól eltérő módon kezelendő. A vásárló a hulladékká vált készüléket köteles a kijelölt gyűjtőhelyre szállítani az elektromos és elektronikai készülékek újrahasznosítása céljából.
Latvian notice Nolietotu iekārtu iznī cināšanas noteikumi lietotājiem Eiropas Savienī bas privātajās mājsaimniecī bās Šāds simbols uz izstrādājuma vai uz tā iesaiņojuma norāda, ka šo izstrādājumu nedrī kst izmest kopā ar citiem sadzī ves atkritumiem. Jūs atbildat par to, lai nolietotās iekārtas tiktu nodotas speciāli iekārtotos punktos, kas paredzēti izmantoto elektrisko un elektronisko iekārtu savākšanai otrreizējai pārstrādei.
Polish notice Pozbywanie się zuż ytego sprzętu przez uż ytkowników w prywatnych gospodarstwach domowych w Unii Europejskiej Ten symbol na produkcie lub jego opakowaniu oznacza, że produktu nie wolno wyrzucać do zwykłych pojemników na ś mieci. Obowiązkiem użytkownika jest przekazanie zużytego sprzętu do wyznaczonego punktu zbiórki w celu recyklingu odpadów powstałych ze sprzętu elektrycznego i elektronicznego.
Slovakian notice Likvidácia vyradených zariadení v domácnostiach v Európskej únii Symbol na výrobku alebo jeho balení označ uje, že daný výrobok sa nesmie likvidovať s domovým odpadom. Povinnosť ou spotrebiteľ a je odovzdať vyradené zariadenie v zbernom mieste, ktoré je urč ené na recykláciu vyradených elektrických a elektronických zariadení.
Spanish notice Eliminación de residuos de equipos eléctricos y electrónicos por parte de usuarios particulares en la Unión Europea Este símbolo en el producto o en su envase indica que no debe eliminarse junto con los desperdicios generales de la casa. Es responsabilidad del usuario eliminar los residuos de este tipo depositándolos en un punto limpio para el reciclado de residuos eléctricos y electrónicos.
B Electrostatic discharge This appendix provides the following information: • How to prevent electrostatic discharge • Grounding methods How to prevent electrostatic discharge To prevent damage to the system, you must follow certain precautions when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device.
If you do not have any of the suggested equipment for proper grounding, have an HP authorized reseller install the part. NOTE: For more information on static electricity, or for assistance with product installation, contact your HP authorized reseller.
C SAN Switch technical specifications This appendix provides the following information: • • • • • • • • • • • General specifications Weight and physical dimensions Facility requirements Environmental requirements Data transmission ranges FC port specifications Serial port specifications Power supply specifications Memory Supported SFPs Supported HBAs SAN Switch installation guide 131
General specifications Table 22 lists general specifications for the SAN Switches. Table 22 General specifications 132 Specification Description Configurable port types F_Port, FL_Port, and E_Port EMC emissions An operating SAN Switch conforms to the emissions requirements specified by the following regulations: • FCC Rules & Regulations, Part 15 subpart B, Class A • CSA C108.
Specification Description System processor for the 4/32B SAN Switch PowerPC 440GP, 333 MHz CPU ANSI protocol FC-PH (FC Physical and Signalling Interface standard) Modes of operation for the 4/8 and 4/16 SAN Switches FC Class 2, Class 3, and Class F Modes of operation for the 4/32, 4/32B and 4/64 SAN Switches FC Class 2 and Class 3 Fabric initialization for the 4/8 and 4/16 SAN Switches Complies with FC-SW-2 Rev. 6.
Weight and physical dimensions Table 23 lists physical properties for the SAN Switches. Table 23 SAN Switch physical dimensions 4/8 and 4/16 SAN Switches 4/32 SAN Switch 4/64 SAN Switch 4/32B SAN Switch Height 4.29 cm (1.69 in) 42.44 mm (1.67 in) 2U or 8.6 cm (3.4 in) 1U or 43.5 mm (1.71 inches) Width 42.85 cm (16.87 in) 429 mm (16.89 in) 42.8 cm (16.8 in) 428.75 mm (16.88 inches) Depth 30.734 cm (12.10 in) 584.2 mm (23.0 in) 61 cm (24 in) 264 mm (10.39 inches) Weight 4.0 kg (8.
Type Requirements 4/64 SAN Switch: Cabinet space of 2U in a EIA 19 in cabinet. All equipment in the cabinet grounded through a reliable branch circuit connection. Additional weight of the switch must not exceed the cabinet’s weight limit. Cabinet must be secured to ensure stability in case of unexpected movement, such as an earthquake.
Environmental requirements To ensure proper operation, the switch must not be subjected to environmental conditions beyond those for which it was tested. The ranges specified in Table 25 list the acceptable environment for both operating and non-operating conditions.
Data transmission ranges See Table 26and Table 27 for SAN Switch data transmission ranges for the different cable types and port speeds. Table 26 Laser data transmission ranges for the 4/8 and 4/16 SAN Switches Port speed Cable size (microns) Short wavelength Long wavelength 1 Gb/s 50 500 m (1,640 ft) N/A 1 Gb/s 62.5 300 m (984 ft) N/A 1 Gb/s 9 N/A Up to 10 km (6.2 miles) optional Long Wave SFPs required 2 Gb/s 50 300 m (984 ft) N/A 2 Gb/s 62.
Table 27 Laser data transmission ranges for the 4/32 SAN Switch Port speed Cable size (microns) Short wavelength Long wavelength Extended long wave length 1 Gb/s 50 500 m (1,640 ft) 10 km (6.2 miles) N/A 62.5 300 m (984 ft) 10 km (6.2 miles) N/A 9 N/A 10 km (6.2 miles) 40 km (24.8 miles) 50 300 m (984 ft) 10 km (6.2 miles) N/A 62.5 150 m (492 ft) 10 km (6.2 miles) N/A 9 N/A 10 km (6.
Table 28 Laser data transmission ranges for the 4/64 SAN Switch Port speed Cable size (microns) Short wavelength Long wavelength Extended long wave length 1 Gb/s 50 500 m (1,640 ft) 10 km (6.2 miles) N/A 62.5 300 m (984 ft) 10 km (6.2 miles) N/A 9 N/A 10 km (6.2 miles) 80 km (50 miles) 50 300 m (984 ft) N/A N/A 62.5 150 m (492 ft) 10 km (6.2 miles) N/A 9 N/A 10 km (6.
Table 29 Laser data transmission ranges for the 4/32B SAN Switch Port speed Cable size (microns) Short wavelength Long wavelength Extended long wave length 1 Gb/s 50 500 m (1,640 ft) N/A N/A 62.5 300 m (984 ft) N/A N/A 9 N/A 10 km (6.2 miles) 40 km (24.8 miles) 50 300 m (984 ft) N/A N/A 62.5 150 m (492 ft) N/A N/A 9 N/A 10 km (6.2 miles) without an HP Extended Fabrics license 50 to 100 km with an HP Extended Fabrics license 40 km (24.8 miles) 50 150 m (492 ft) N/A N/A 62.
Additionally, the ports autonegotiate at 1, 2, or 4 Gb/s and meet all required safety standards. For more information about these standards, see Regulatory compliance notices. 4/32B SAN Switch FC port specifications The FC ports are compatible with SWL, LWL, and ELWL SFP transceivers. The strength of the signal is determined by the type of transceiver in use. The ports meet all required safety standards. For more information about these standards, see Regulatory compliance notices.
Table 30 Cabling pinouts Pin Signal Description 1 Not supported Not supported 2 RxData Receive data 3 TxData Transmit data 4 Not supported Not supported 5 GND Logic ground 6 Not supported Not supported 7 Not supported Not supported 8 Not supported Not supported 9 Not supported Not supported A 3.0 m (10 ft) serial cable is provided with the switch. It can be converted from a DB-9 serial cable to an RJ-45 serial cable by removing the adapter on the end of the cable.
Power supply specifications The power supplies are universal and capable of functioning worldwide without using voltage jumpers or switches. They meet IEC 61000-4-5 surge voltage requirements and are autoranging in terms of accommodating input voltages and line frequencies. Each power supply integrates its own built-in fan for cooling, pushing the air forward toward the port side of the switch. Table 31 lists the power supply specifications.
Memory Table 32 specifies 4/8 and 4/16 SAN Switch memory. Table 32 4/8 and 4/16 SAN Switch memory specifications Memory type Install memory Main Memory (SDRAM) 128 MB Compact Flash 256 MB Table 33 specifies 4/32 and 4/64 SAN Switch memory.
Supported HBAs For a list of HBAs that have been tested and are known to work with the SAN switches, refer to the latest version of the HP StorageWorks SAN design reference guide: http://www.hp.com/go/sandesignguide.
SAN Switch technical specifications
Glossary This glossary defines terms used in this guide or related to this product. It is not a comprehensive glossary of computer terms. alias server A fabric software facility that supports multicast group management. API Application programming interface. A defined protocol that allows applications to interface with a set of services. arbitrated loop A shared 100 Mb/s Fibre Channel transport structured as a loop. Can support up to 126 devices and one fabric attachment.
CRC Cyclic redundancy check. A check for transmission errors that is included in every data frame. defined zone configuration The set of all zone objects defined in the fabric. May include multiple zone configurations. See also zone, zone configuration. directory service See SNS. DLS Dynamic load sharing. Dynamic distribution of traffic over available paths. Allows for recomputing of routes when an Fx_Port or E_Port changes status.
fabric An FC network containing two or more switches in addition to hosts and devices. May also be called a switched fabric. fabric name The unique identifier assigned to a fabric and communicated during login and port discovery. FCIA Fibre Channel Industry Association. An international organization of FC industry professionals. Among other things, provides oversight of ANSI and industry standards. FCP Fibre Channel Protocol. Mapping of protocols onto the FC standard protocols.
FSPF Fabric shortest path first. HP routing protocol for FC switches. Fx_Port A fabric port that can operate as an F_Port or FL_Port. G_Port Generic port. A port that can operate as an E_Port or F_Port. A port is defined as a G_Port when it is not yet connected or has not yet assumed a specific function in the fabric. See also E_port, F_port, U_Port. hard address The AL_PA that an NL_Port attempts to acquire during loop initialization. See also defined zone configuration.
LIP Loop initialization primitive. The signal that begins initialization in a loop. It indicates either loop failure or the resetting of a node. LM_TOV Loop master time-out value. The minimum time that the loop master waits for a loop initialization sequence to return. loop failure Loss of signal within a loop for any period of time; loss of synchronization for longer than the time-out value. Loop_ID A hexadecimal value representing one of the 127 possible AL_PA values in an arbitrated loop.
non-participating mode A mode in which an L_Port in a loop is inactive and cannot arbitrate or send frames, but can retransmit any received transmissions. This mode is entered if there are more than 127 devices in a loop and an AL_PA cannot be acquired. See also L_Port, ???. Nx_Port A node port that can operate as an N_Port or NL_Port. packet A set of information transmitted across a network.
public loop An arbitrated loop that includes a participating FL_Port and may contain both public and private NL_Ports. See also arbitrated loop. public NL_Port An NL_Port that logs in to the fabric, can function within a public or private loop, and can communicate with private or public NL_Ports. See also private loop. quad A group of four adjacent ports that share a common pool of frame buffers. R_A_TOV Resource allocation time-out value.
them as required to other devices in the fabric. May also be referred to as a directory service. 154 switch Hardware that routes frames according to FC protocol and is controlled by software. switch port A port on a switch. Switch ports can be E_Ports, F_Ports, or FL_Ports. SWL Short wavelength. A type of fiber optic cabling that is based on 850 mm lasers and supports link speeds up to 2 Gb/s. May also refer to the type of transceiver.
zone, but are not visible to any outside the zone. See also defined zone configuration, enabled zone configuration. zone configuration A specified set of zones. Enabling a configuration enables all zones in that configuration. See also defined zone configuration, enabled zone configuration.
Glossary
Index A activating 4/16 ports, 17 activating 4/32 ports, 22 activating 4/32B ports, 31 audience, 11 authorized reseller, 14 B boot specifications, 88 C cable management, 52 cables, connecting, 60 cabling and configuring, 52 chassis 4/32, 20 4/32B, 29 4/64, 25 4/8 and 4/16, 17 commands configupload, 60 configure, 58 date, 61 errshow, 89 fabricshow, 58, 60 fastboot, 88 ipaddrshow, 57 licenseadd, 18, 23 licenseshow, 18, 23 portdisable, 72, 77, 82, 87 portenable, 18, 23, 72, 77, 82, 87 portshow, 17, 23, 3
document conventions, 12 related documentation, 11 E electrical considerations, 38 environmental considerations, 38 environmental requirements, 136 errshow command, 89 Ethernet connection, creating, 58 F fabric license, 18 fabricshow command, 58, 60 facility requirements, 134 fastboot command, 88 FC port specifications, 140 features 4/32, 20 4/32B, 29 4/64, 24 4/8 and 4/16, 16 fibre channel ports, 32 G general specifications, 132 grounding methods, 129 H HBAs, supported, 145 help obtaining, 13 HP we
portstart command, 18, 23 POST results, interpreting, 88 POST specifications, 88 power supply specifications, 143 power supply, replacing, 93, 100 powering on and off, 66 R rack specifications, 39 related documentation, 11 S safety considerations, 38 SAN Switch 4/8 and 4/16 models, 15 serial connection, 53 serial port specifications, 141 setting the IP address, 57 SFP transceivers installing, 59 replacing, 110 supported, 144 shipping carton contents, 35 specifications environmental requirements, 136 fac