® Intel PRO/100 SP Mobile Combo Adapter User’s Guide OPTIONS by IBM
Note: Before using this information and the product is supports, read the information under “Appendix E. Product warranty and notices” on page E-1. First Edition (February 2001) © Copyright International Business Machines Corporation 2001. All rights reserved. US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract with IBM Corp.
Contents Safety: Read first . About this book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v . vii Part 1: Installation and user’s guide . . . . . . . . . . . . . 1-1 Appendix A. Troubleshooting . . . . . . . . . . . . . . . A-1 Appendix B. Modem function . . . . . . . . . . . . . . . B-1 Appendix C. Specifications . . . . . . . . . . . . . . . C-1 Appendix D.
iv ® Intel PRO/100 SP Mobile Combo Adapter: User’s Guide
Safety: Read first Before installing this product, read the Safety Information. Antes de instalar este produto, leia as Informações de Segurança. Pred instalací tohoto produktu si prectete prírucku bezpecnostních instrukcí. Læs sikkerhedsforskrifterne, før du installerer dette produkt. Ennen kuin asennat tämän tuotteen, lue turvaohjeet kohdasta Safety Information. Avant d’installer ce produit, lisez les consignes de sécurité. Vor der Installation dieses Produkts die Sicherheitshinweise lesen.
Antes de instalar este produto, leia as Informações sobre Segurança. Pred inštaláciou tohto zariadenia si pečítaje Bezpečnostné predpisy. Antes de instalar este producto lea la información de seguridad. Läs säkerhetsinformationen innan du installerar den här produkten.
About this book ® This manual contains instructions for installing and using your Intel PRO/100 SP Mobile Combo Adapter. The manual is divided into two parts: Part 1: Installation and user’s guide: This guide contains the product description, hardware and software installation. Part 2 Appendixes This section contains troubleshooting, modem function, specifications, help and service information, and warranty and notices. Online user’s guide The complete User’s Guide is located on the Intel CD.
viii ® Intel PRO/100 SP Mobile Combo Adapter: User’s Guide
Part 1: Installation and user’s guide This section contains instructions on how to install and use the Intel PRO/100 SP Mobile Combo Adapter. System requirements Before installing the PRO/100 adapter, be sure that your system has the following: v One open Mini-PCI slot v The latest BIOS for your computer ® ® v Microsoft Windows Millennium Edition (Me), Microsoft Windows 2000 ® Professional, Microsoft Windows NT 4.0 Workstation, Windows 98 or Windows 95 v Windows NT 4.
Installing the Ethernet and modem device drivers in Windows Me To install the PCI Ethernet Controller device driver and the Lucent Win Modem device driver in Windows Me, do the following: Note: Use the Add New Hardware Wizard for installing only the PCI Ethernet Controller. See instructions below. 1. Start Windows Me. The Add New Hardware Wizard window opens and indicates that the PCI Ethernet Controller was found. 2. Insert the Intel Driver CD in the CD-ROM drive and click Next. 3.
8. Click Next on Driver Files Search Results. 9. If The Digital Signature Not Found window opens, click Yes to continue. 10. When installation of the PCI Ethernet Controller completes, click Finish. 11. Click Start→Run. 12. Type x:\modem\win2K\setup.exe where x is the drive letter of the CD-ROM drive. 13. Click OK on Do you want to install the modem driver? 14. If the Digital Signature Not Found window opens, click Yes to continue. The Lucent Win Modem driver will complete loading.
The Installing Modem Drivers window opens and the Wizard finds a Lucent Win Modem. 17. Restart the computer to finish the Lucent Win Modem installation. Installing the Ethernet and modem device drivers in Windows 95 To install the PCI Ethernet Controller device driver and the Lucent Win Modem device driver in Windows 95, do the following: Note: You will need your Windows 95 installation CD or diskette to install the device driver. For Windows 95 OSR0 or OSR1 1. Start Windows 95.
14. Click Start→Run. 15. Enter x:\modem\win9x\setup.exe where x is the drive letter of the CD-ROM drive. 16. Follow the instructions on the screen. 17. Restart the computer. As you configure your communication software, you will be prompted to select a modem. 18. Select Lucent Win Modem to finish the Lucent Win Modem device driver installation. For Windows 95 OSR2.1 or OSR2.5 1. Start Windows 95. The Update Device Driver Wizard window opens for the PCI Ethernet Controller. 2.
16. Follow the instructions on the screen. 17. Restart the computer. As you configure your communication software, you will be prompted to select a modem. 18. Select Lucent Win Modem to complete the Lucent Win Modem device driver installation. Installing the Ethernet and modem device drivers in Windows NT 4.0 To install the PCI Ethernet Controller driver and the Lucent Win Modem in Windows NT 4.0, do the following: 1. Start Windows. 2. Click the Network icon in the Control Panel. 3.
21. Type x:\modem\winnt\setup.exe where x is the drive letter of the CD-ROM drive. 22. Click OK on Do you want to install the modem driver? After the Lucent Win Modem driver installs, click OK to restart your computer. 23. Exit Windows Explorer and restart to complete installation of the Lucent Win Modem driver. Using the modem abroad This section provides information for using the modem outside your country.
Advanced features This section presents advanced information for adapters that support the advanced features listed. Tasks within this section should be handled only by system administrators. Advanced adapter features To access the advanced features of the adapter, perform the following: 1. In the Control Panel, double-click Network. 2. Select the adapter and click Properties. 3. Click the Advanced tab. The Combo card has the following advanced features: 802.1p/802/1Q Tagging IEEE 802.
1. From the Windows 98 desktop, right-click on My Computer and choose Properties. 2. The System Properties window opens. Your Windows 98 version is listed under System. Enable PME Use this setting to adjust the power management compatibility of the adapter. The default setting is Disable. To explicitly allow wake up with a Magic Packet from shutdown under APM power management mode, change the setting to Enable.
Although this is the safest setting, the best performance is achieved when the threshold parameter is as low as possible without producing underruns. To experiment, set the parameter to 16. Then, if performance drops significantly, increase the value in small increments. Coalesce Buffers The rcommended value is 8 with a range of 1–32. This specifies the number of memory buffers available to the driver in case the driver runs out of available Map Registers.
requires only one PCI transaction, the PCI bus is more efficient, but transmit time is slightly longer. When the option is disabled, the packets are not coalesced, and each packet requires several PCI transactions. The PCI bus is less efficient, but transmit time is faster. Receive Buffers The recommended value is 32 and the range is 1–1024. This specifies how many buffers the driver is to use when copying data to the protocol memory.
When traffic is prioritized at the host or entry point of the network, network devices can base forwarding decisions on priority information defined in the packet. Priority Packet prioritizes traffic on the basis of priority filters—parameters you assign to be applied to outgoing (transmit) packets. Using the Priority Filter Wizard, you can set up predefined or custom priority filters on the basis of node (MAC) address, Ethernet type, or various properties of the protocol and port.
Wake on LAN The Wake on LAN (WOL) feature operates according to a published specification. In simple terms, the specification enables designers to build network adapters that are capable of “listening” to network activity even when the computer is turned off. WOL adapters have a special low-power standby mode that is active when the rest of the computer is without power. The adapter will respond to a special wake-up packet sent by another computer or network device.
3. On the Adapters tab, select the adapter you want to be on a VLAN. 4. Click Properties. 5. In PROSet, click Join VLAN. 6. Type the VLAN ID and the VLAN Name. Note: The VLAN ID must match the VLAN ID on the switch. The Valid ID range is from 0–4095. The VLAN Name is for informational purposes only, and does not have to match the name on the switch. 7. Click Join VLAN. 8. Repeat Steps 3 to 6 for each VLAN you want the server to join. The VLANs you add are listed on the Adapters tab. 9.
Configuration Setup The Boot Agent software provides configuration options that allow you to customize the behavior of the Boot Agent software. Changing the Boot Agent configuration will usually be required only the first time you add a new network adapter to a client computer within your network.
1-16 ® Intel PRO/100 SP Mobile Combo Adapter: User’s Guide
Appendix A. Troubleshooting This section contains information on troubleshooting for the network adapter and modem. Troubleshooting network adapter The following table describes troubleshooting for the network adapter. Problem Action The Combo card v Make sure that the cable is installed properly. The network can’t connect to the cable must be securely attached to the Ethernet connector and Network. hub. The maximum allowable distance from adapter to hub is 100 meters.
Troubleshooting modem The following table describes troubleshooting the modem. Problem Action Your modem does not work properly after you install the device driver. Check the following: v The cable is connected to the modem card correctly. v You selected Intel PRO/100 SP Mobile Combo Adapter application setting. v You are using the driver that is on the device drivers CD shipped with the combo card.
Appendix B. Modem function This section describes information about general modem hardware function, AT command summary, and AT commands reference S-registers. For additional information, refer to Lucent Technologies, Host-Based Controller Modem AT Command Set, Version 1.1, June 15, 1998. General Modem Hardware Function Table 3 below contains the general modem hardware functions supported. Table 3: Supported Functions Data Modes: ITU V.90, V.34, V.32bis, V.32, V.22bis, V.22, V.21; Bell 103, 212A V.
Table 3: Supported Functions Separate Homologation Country parameters in binary file [Except OS/2] CLKRUN# support. CLKRUN# should not be asserted if no data transaction for modem (or LAN) NT 4.0 APM Support through TP port DD for Windows NT 4.0 with the latest service pack Note: Meter Tone (billing tone) filtering for Switzerland and Germany is not included and must be provided by the user. AT command summary The following tables summarize the commands implemented by the modem.
Table 4: AT Command Set Summary. The following table is from Lucent Technologies, Host-Based Controller Modem AT Command Set, Version 1.1, June 15, 1998.
Table 5: The S-Register Summary. The S-registers 42 and 43 are for testing and debugging purposes only. Register Default Description S10 20 Automatic disconnect delay S11 95 DTMF dialing speed S12 50 Escape guard time S14 8 General bit-mapped options status S21 48 V.24 bit-mapped options status S22 112 Results bit-mapped options status S24 10 Timer to control sleep mode S28 1 V.
To modify the value of an S-register: TYPE: ATSn = r where n is the register number, and r is the new register value. PRESS: Enter S0 Auto Answer Ring Number This register determines the number of rings the modem will count before automatically answering a call. Enter 0 (zero) if you do not want the modem to automatically answer at all. When disabled, the modem can only answer with an ATA command. Range: 0-255 Default: 0 Units: rings S1 Ring Counter This register, Ring Counter, is read only.
S3 Command Line Termination Character (user defined) This register determines the ASCII values as the carriage return character. This character is used to end command lines and result codes. Range: 0-127, ASCII decimal Default: 13 (carriage return) Units: ASCII Note: This register value is not stored with &W command. S4 Response Formatting Character (user defined) This register determines the ASCII value used as the line feed character.
S6 Wait Before Dialing This register sets the length of time, in seconds, that the modem must wait (pause) after going off-hook before dialing the first digit of the telephone number. The modem always pauses for a minimum of two seconds, even if the value of S6 is less that two seconds. The wait for dial tone call progress feature (W dial modifier in the dial string) will override the value in register S6. This operation, however, may be affected by some ATX options according to country restrictions.
Units: seconds S10 Automatic Disconnect Delay This register sets the length of time, in tenths of a second, that the modem waits before hanging up after a loss of carrier. This allows for a temporary carrier loss without causing the local modem to disconnect. The actual interval the modem waits before disconnecting is the value in register S10. Range: 1-254 Default: 20 Units: .1 seconds S11 DTMF Dialing Speed This register determines the dialing speed which is prefixed for each country.
0 = Numeric (V0) 1 = Verbose (Vl) (Default) Bit 6 Pulse dial PPS selection (&Pn) 0 = 10 PPS (&p0, &p1) (Default) 1 = 20 PPS (&p2) Default: 8 (00001000b) S21 V.24/General Bit Mapped Options Status Indicates the status of command options. Only bits 3, 4, and 5 are used, read-only.
5 = X2 selected 6 = X3 selected 7 = X4 selected (Default) Bit 7 Pulse dial make/break ratio (&Pn) 0 = 33/67 make/break ratio (&P1, &P2) (Default) 1 = 39/61 make/break ratio (&P0) Default: 112 (01110000b) S24 Timer to Control Sleep Mode This command displays the number of seconds of inactivity (no characters sent from the DTE, no RING) in the off-line command state before the modem places itself into standby mode. A value of zero prevents standby mode. S24 is an alias for S89.
Range: 0-255 Default: 0 S32 Synthetic Ring Volume This register specifies a synthetic ring volume. Range: 0-255 (allowed, but not meaningful) Default: 10 S33 Synthetic Ring Frequency This register specifies a synthetic ring frequency. There are five choices, with 0 meaning disabled. Range: 0-5 Default: 0 S35 Data Calling Tone Data Calling Tone is a tone of certain frequency and cadence as specified in V.25 which allows remote Data/FAX/Voice discrimination. The frequency is 1300 Hz with a cadence of .
S37 = 4 reserved S37 = 5 1200 bit/s S37 = 6 2400 bit/s S37 = 7 4800 bit/s S37 = 8 7200 bit/s S37 = 9 9600 bit/s S37 = 10 12000 bit/s S37 = 11 14400 bit/s S37 = 12 16800 bit/s S37 = 13 19200 bit/s S37 = 14 21600 bit/s S37 = 15 24000 bit/s S37 = 16 26400 bit/s S37 = 17 28800 bit/s S37 = 18 31200 bit/s S37 = 19 33600 bit/s S38 K56flex Downstream Rate To force a particular K56flex downstream rate, use S-register S38. S38=0 disables K56flex, and may allow a more reliable V.34 connection.
S38=3 34 kbit/s S38=4 36 kbit/s S38=5 38 kbit/s S38=6 40 kbit/s S38=7 42 kbit/s S38=8 44 kbit/s S38=9 46 kbit/s S38=10 48 kbit/s S38=11 50 kbit/s S38=12 52 kbit/s S38=13 54 kbit/s S38=14 56 kbit/s The number of robbed-bit signaling (RBS) frames detected decreases the true DCE rate per the following table: Table 6: Effect of RBS Frames on DCE Rate RBS Links Rate Hit (kbit/s) 0 0 1 2 2 4 3 4 4 6 5 8 6 8 For example, if S38=10 and there are 3 RBS links, the K56flex downstream rate will be 48-4=
One special value of S38, S38 = 251, is used for back-to-back (factory) testing of V.34 rates, with DSP code running in external memory. Set S38=251 on both originating and answering modems. (This feature is not valid with ramless solution.) S42 Auto Rate (default 1, range 0-1) This command is used for testing and debugging only. V.32bis and V.22bis auto rate is disabled. Retrain operation is disabled or enabled in data mode, and fallback is disabled in data mode.
Table 7: S36 and S48 Configuration Settings S48 = 7 S48 = 128 S36 = 1, 3 LAPM or async async S36 = 4, 6 LAPM, MNP, or hangup MNP or hangup S36 = 5, 7 LAPM, MNP, or async MNP or async S89 Timer to Control Sleep Mode This command displays the number of seconds of inactivity (no characters sent from the DTE, no RING) in the off-line command state before the modem places itself into standby mode. A value of zero prevents standby mode.
S108=33 A-law S108=7 default, or any other value: Coding as specified by digital modem in V.8bis information. If an old server does not tell its code type in V.8bis, then the client modem chooses based on its country ID. m-law regions are Japan, Taiwan, Korea, Hong Kong, North America, and Latin America. Everywhere else is A-law. (This S - Register is valid only in K56flex mode.
Appendix C. Specifications This section provides information about the Adapter and LAN specifications. Adapter specifications Table 8: Specifications Feature Value Power requirements 300mA @ =5Vdc (1.
Table 9: Specifications Feature Value Diagnostic Software On-board PROSet Responder Duplex mode C-2 ® Full duplex / Half duplex Intel PRO/100 SP Mobile Combo Adapter: User’s Guide
Appendix D. Help and service information This section contains information on how to obtain online and telephone technical support. Online technical support Online technical support is available during the life of your product. Online assistance can be obtained through the Personal Computing Support Web site and the IBM Automated Fax System. Online technical support IBM Personal Computing Support Web site http://www.ibm.com/pc/support IBM Automated Fax System 1-800-426-3395 (U.S.
For the support telephone number and support hours by country, refer to the following table or to the enclosed technical support insert. If the number is not provided, contact your IBM reseller or IBM marketing representative. Response time may vary depending on the number and nature of the calls received. Support 24 hours a day, 7 days a week Canada (Toronto only) 416-383-3344 Canada (all other) 1-800-565-3344 U.S.A. and Puerto Rico 1-800-772-2227 All other countries Go to http://www.ibm.
Appendix E. Product warranty and notices This section contains produce warranty information and notices. and Warranty Statements The warranty statements consist of two parts: Part 1 and Part 2. Part 1 varies by country. Part 2 is the same for both statements. Be sure to read both the Part 1 that applies to your country and Part 2. v United States, Puerto Rico, and Canada (Z125-4753-05 11/97) (Part 1 General Terms on page E-1.
During the warranty period IBM or your reseller, if approved by IBM to provide warranty service, will provide repair and exchange service for the Machine, without charge, under the type of service designated for the Machine and will manage and install engineering changes that apply to the Machine.
To obtain warranty service for the Machine, contact your reseller or IBM. In the United States, call IBM at 1-800-772-2227. In Canada, call IBM at 1-800-565-3344. (In Toronto, call 416-383-3344.) You may be required to present proof of purchase. IBM or your reseller provides certain types of repair and exchange service, either at your location or at a service center, to keep Machines in, or restore them to, conformance with their Specifications.
IBM is responsible for loss of, or damage to, your Machine while it is 1) in IBM’s possession or 2) in transit in those cases where IBM is responsible for the transportation charges. Neither IBM nor your reseller is responsible for any of your confidential, proprietary or personal information contained in a Machine which you return to IBM or your reseller for any reason. You should remove all such information from the Machine prior to its return.
IBM Statement of Warranty Worldwide except Canada, Puerto Rico, Turkey, United States (Part 1 - General Terms) This Statement of Warranty includes Part 1 - General Terms and Part 2 Country-unique Terms. The terms of Part 2 may replace or modify those of Part 1. The warranties provided by IBM in this Statement of Warranty apply only to Machines you purchase for your use, and not for resale, from IBM or your reseller.
THESE WARRANTIES ARE YOUR EXCLUSIVE WARRANTIES AND REPLACE ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THESE WARRANTIES GIVE YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM JURISDICTION TO JURISDICTION.
serial-numbered Machine and 2) at an engineering-change level compatible with the feature, conversion, or upgrade. Many features, conversions, or upgrades involve the removal of parts and their return to IBM. A part that replaces a removed part will assume the warranty service status of the removed part. Before IBM or your reseller exchanges a Machine or part, you agree to remove all features, parts, options, alterations, and attachments not under warranty service. You also agree to 1.
1. damages for bodily injury (including death) and damage to real property and tangible personal property; and 2. the amount of any other actual direct damages, up to the greater of U.S. $100,000 (or equivalent in local currency) or the charges (if recurring, 12 months’ charges apply) for the Machine that is the subject of the claim. This limit also applies to IBM’s suppliers and your reseller. It is the maximum for which IBM, its suppliers, and your reseller are collectively responsible.
PEOPLE’S REPUBLIC OF CHINA: Governing Law: The following is added to this Statement: The laws of the State of New York govern this Statement. INDIA: Limitation of Liability: The following replaces items 1 and 2 of this Section: 1. liability for bodily injury (including death) or damage to real property and tangible personal property will be limited to that caused by IBM’s negligence; 2.
Yugoslav Republic of Macedonia (FYROM), Moldova, Poland, Romania, Russia, Slovak Republic, Slovenia, or Ukraine, you may obtain warranty service for that Machine in any of those countries from either (1) an IBM reseller approved to perform warranty service or (2) from IBM. The applicable laws, Country-unique terms and competent court for this Statement are those of the country in which the warranty service is being provided.
Production Status: The following paragraph replaces this Section: Each Machine is newly manufactured. It may incorporate in addition to new parts, re-used parts as well. Limitation of Liability: The following is added to this Section: The limitations and exclusions specified in the Statement of Warranty will not apply to damages caused by IBM with fraud or gross negligence and for express warranty. In item 2, replace ″U.S. $100,000″ with ″1.000.000 DEM.
The following replaces the second paragraph of this Section: Unless otherwise provided by mandatory law, IBM and your reseller are not liable for any of the following: (items 1 and 2 unchanged) 3) indirect damages, even if IBM or your reseller is informed of their possibility.
IBM may not offer the products, services, or features discussed in this document in other countries. Consult your local IBM representative for information on the products and services currently available in your area. Any reference to an IBM product, program, or service is not intended to state or imply that only that IBM product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any IBM intellectual property right may be used instead.
will be the same on generally available systems. Furthermore, some measurements may have been estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment. Trademarks The following terms are trademarks of the IBM Corporation in the United States, other countries or both: IBM HelpCenter Wake on LAN Intel is a trademark of the Intel Corporation in the United States other countries, or both.
IBM authorized dealers. IBM is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules.
IBM can not accept responsibility for any failure to satisfy the protection requirements resulting from a non-recommended modification of the product, including the fitting of non-IBM option cards. This product has been tested and found to comply with the limits for Class B Information Technology Equipment according to CISPR 22/European Standard EN 55022.
Questo prodotto è conforme alle normative di protezione ai sensi della Direttiva del Consiglio dell’Unione Europea 89/336/CEE sull’armonizzazione legislativa degli stati membri in materia di compatibilità elettromagnetica. IBM non accetta responsabilità alcuna per la mancata conformità alle normative di protezione dovuta a modifiche non consigliate al prodotto, compresa l’installazione di schede e componenti di marca diversa da IBM.
to your line, as determined by the REN, you should call your local telephone company to determine the maximum REN for your calling area. 3. If the device causes harm to the telephone network, the telephone company may discontinue your service temporarily. If possible, they will notify you in advance; if advance notice is not practical, you will be notified as soon as possible. You will be advised of your right to file a complaint with the FCC. 4.
Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas. Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.
AVIS : L’indice d’équivalence de la sonnerie (IES) assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent être raccordés à une interface. La terminaison d’une interface téléphonique peut consister en une combinaison de quelques dispositifs, à la seule condition que la somme d’indices d’équivalence de la sonnerie de tous les dispositifs n’excède pas 5.
Network Compatibility Declaration This equipment is intended for connection to the Public Switched Telephone Network, and supports both DTMF signalling and pulse dialing for the network addressing. It has been designed to be compatible and interwork with the European networks in EC and EFTA countries, which are: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Liechtenstein, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, United Kingdom.
Telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Tel ecom’s network services. Some parameters required for compliance with Telecom’s Telepermit requirements are dependent on the equipment (PC) associated with this device.
Appendix F. User notices v This card is intended for use with UL1950/EN60950/IEC60950 (or other NTRL) listed ITE computers that contain a Mini PCI type 3A connector. v Care should be taken to avoid damaging the insulation tape on the Xircom Mini PCI Modem 56 + 10/100 Ethernet card. Do not cut, tear, pierce, or remove the insulation tape. v (English) CAUTION: To reduce the risk of fire, use only No. 26 AWG telecommunication line cord.
F-2 ® Intel PRO/100 SP Mobile Combo Adapter: User’s Guide
Part Number: 06P3814 Printed in the United States of America on recycled paper containing 10% recovered post-consumer fiber.
