Megapixel HD Analog Camera User’s Manual Version 1.0.
Table of Contents 1 2 General Introduction .................................................................................................................. 1 1.1 Overview ........................................................................................................................ 1 1.2 Features ......................................................................................................................... 1 1.3 Functions ..........................................................
Welcome Thank you for purchasing our analog camera! This user’s manual is designed to be a reference tool for your system.
Important Safeguards and Warnings 1．Electrical safety All installation and operation here should conform to your local electrical safety codes. The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited power source is rated 12V DC in the IEC60950-1. We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation.
Please shut down the device and then unplug the power cable before you begin daily maintenance work. Use the dry soft cloth to clean the device. If there is too much dust, please use the water to dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the device. Please put the dustproof cap to protect the CMOS component when you do not use the camera.
1 General Introduction 1.1 Overview This series megapixel analog HD camera conforms to the HD-AVS standard. It supports video signal high-speed long distance transmission without any delay. It can be controlled by the DVR conforming to the HD-AVS. 1.2 Features High-performance CMOS image sensor, megapixel definition. HD video, coaxial cable to transmit the control signal. Support 75-3 coaxial cable transmission without any loss. Transmission distance is over 500m.
Model 1 Megapixel HD-AVS Analog Camera Parameter AVS-D2110 Video Processor 1/3" 1.3 Megapixel CMOS Video Format PAL/NTSC Effective Pixel 1280(H)×960(V) Min Illumination AVS-B2100 AVS-B2110 Color: 0.01Lux/F1.2（0 Lux with IR） Electronic Shutter PAL：4/25s～1/45,000s NTSC：4/30~1/54,000s Video Standard HD-AVS/CVBS compliance Video Frame Rate 1280×720@25 fps；1280×720@30 fps； 1280×720@50 fps；1280×720@60 fps Lens Port M12 Lens Type 2.8/3.
3
2 Framework 2.1 Dimensions 2.1.1 AVS-D2110 Please refer to the following figures for the dimension information. The unit is mm. See Figure 2-1. Figure 2-1 2.1.2 AVS-B2100 Please refer to the following figures for the dimension information. The unit is mm. See Figure 2-2. Figure 2-2 2.1.3 AVS-B2110 Please refer to the following figures for the dimension information. The unit is mm. See Figure 2-3.
Figure 2-3 When the standard definition/high definition switch control cable is short circuit, system outputs standard definition video. Otherwise, when the circuit is open, system outputs the high definition video.
3 Installation Important Before the installation, please make sure the installation surface can sustain at least 3X weight of the bracket and the camera. 3.1 IR Waterproof Dome Camera Step1 Please take the installation position map in the accessories bag, and then paste it on the ceiling or the wall according to your monitor area requirements. Draw and then dig three holes in the installation surface and then insert three expansion bolts in the holes. Secure these three bolts firmly.
Important Do not remove the screw. Loosen a little bit will be OK. Please secure after you completed the setup. Figure 3-2 Step 4 Line up the bulge of the decoration ring to the nick of the camera body and install along the tilt installation. Push and then turn decoration ring clockwise. The installation completed after you secure the decoration ring.
This series product supports wall-mount. Please refer to the steps listed below for installation information. Step 1 Please dig four installation holes in the installation surface according to the four holes of the bottom of the bracket. Insert four expansion bolts from the accessories bag into the holes and then use four self-tapping screws to secure the bracket on the installation surface. See Figure 3-4.
Figure 3-5 Step 2 First prepare the cable according to the cable. Line up the three screw holes at the bottom of the bracket to the three installation holes in the wall or the ceiling, and then insert three screws to the three holes of the chassis of the bracket and fix them firmly. Now secure the bracket on the installation surface of the wall or the ceiling. Step 3 Adjust the camera to the proper monitor area via the three directions indicated in Figure 3-6 after you fixed the camera.
You can use the terminal encode devices to view the monitor video.
4 Menu 4.
The 1st Menu The 2nd Menu CONTRA ST SATURA TION BRIGHT NESS RETURN EXIT The 3rd Menu EDGE AUTO/MANUAL VALUE 0-15（For manual mode only） RETURN 0-255 0-15 70-250， +10 SAVE CANCEL RESET 4.2 Note Parameter Function 3D NR It is to reduce video noise. The larger the number is, the lower the noise is. The details of the video may disappear if the value here is too large. Contrast It is to adjust video contrast. The larger the number is, the higher the contrast is.
Appendix Toxic or Hazardous Materials or Elements Toxic or Hazardous Materials or Elements Component Name Pb Hg Cd Cr VI PBB PBDE Circuit Board Component ○ ○ ○ ○ ○ ○ Device Construction Material ○ ○ ○ ○ ○ ○ Wire and Cable ○ ○ ○ ○ ○ ○ Packing Components Accessories ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ O: Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ/T11363-2006 standard.
