HD IR Waterproof Fixed IP Camera （With Integrated Bracket） User’s Manual Version 3.2.
Welcome Thank you for purchasing our IP camera! This user’s manual is designed to be a reference tool for your system.
Important Safeguards and Warnings 1．Electrical safety All installation and operation here should conform to your local electrical safety codes. The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited power source is rated 12V DC or 24V AC in the IEC60950-1. This series product can not support these two modes at the same time. We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation.
Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens surface. Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the device. Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera. 7. Accessories Be sure to use all the accessories recommended by manufacturer.
Table of Contents 1 General Introduction ..................................................................................................................1 1.1 Overview ........................................................................................................................1 1.2 Features.........................................................................................................................1 1.3 Specifications ............................................................
1 General Introduction 1.1 Overview This series IP camera integrates the traditional camera and network video technology. It adopts audio and video data collection, transmission together. It can connect to the network directly without any auxiliary device. This series IPC uses standard H.264 video compression technology and G.711a audio compression technology, which maximally guarantee the audio and video quality. It supports the IR night vision function.
z z z z z Built-in IR light. Support IR night vision. Support picture parameter setup such as electronic shutter and gain setup. Backlight compensation: screen auto split to realize backlight compensation to adjust the bright. Support video watermark function to avoid vicious video modification. The enclosure conforms to the IP 66 protection. Has the waterproof function. 1.3 Specifications 1.3.1 Performance System Please refer to the following sheet for IPC performance specification.
Video Bit Rate Video Flip Snapshot Privacy Mask Video Setup Video Information NTSC: NTSC: NTSC: Main stream： Main stream Main stream （3M@15fps ,10 （1080P@30fps, （1.3M@30fps, 80P@30fps, SXGA@30fps, 720P@30fps, SXGA@30fps, 1.3M@30fps, 704*480@30fp 1.3M@30fps, 720P@30fps, s） 720P@30fps, 704*480@30fps Extra stream 704*480@30fps ）， （704*480@30f ）， Extra stream ps,352*240@3 Extra stream （704*480@30fp 0fps） （704*480@30f s,352*240@30fps ps,352*240@30f ） ps） H.264: 56Kbps-8192Kbps.
Power General Parameter Power Consumption Working Temperature Working Humidify Dimensions(mm) Weight Installation Support AC24V/DC12V power. (Can not support these two modes at the same time.) 8W MAX (10W MAX when ICR switch) -10℃~+60℃ 10%~90% φ104*306.7 1250g（Excluding box） Bracket is included in the accessories bag. 1.3.2 Factory Default Setup Please refer to the following sheet for factory default setup information.
Setup Default Setup IPCIPCHFW3300C HFW3200C Item Sub Stream Snapshot Video Overlay Watermark character DigitalCCTV Enable Enable Bit stream type General Encode mode H.
Setup IP Version Default Setup IPCIPCHFW3300C HFW3200C IPV4 IP Address 192.168.1.108 Subnet Mask 255.255.255.0 Default Gateway 192.168.1.1 Preferred DNS 8.8.8.8 Alternate DNS 8.8.8.
Setup Default Setup IPCIPCHFW3300C HFW3200C Item UPnP SNMP Bonjour Multicast QoS Video detect Event Motion Detect Password N/A Sender none Authenticati on (Encryption mode) N/A Title (Subject) IPC Message Attachment N/A Mail Receiver 0 seconds Email Test Disable，interval=60 minutes Enable UPnP Disable SNMP v1 Disable SNMP v2 Disable SNMP Port 161 Read Community public Write Community private Trap Address N/A Trap Port 162 Enable Enable Server Name MAC Multicast Ad
Setup Alarm Delay Default Setup IPCIPCHFW3300C HFW3200C 10 seconds Send Email Disable Snapshot Disable Enable Disable Record Channel Enable Record Delay 10 seconds Relay out Enable Record Delay 10 seconds Send Email Disable Snapshot Disable Enable Disable Relay in Alarm 1 Anti-dither 0 seconds Sensor Type NO Record Channel Enable Record Delay 10 seconds Relay out Enable Alarm Delay 10 seconds Send Email Disable Snapshot Disable Item Video Masking Alarm Alarm Activa
Setup Send email Default Setup IPCIPCHFW3300C HFW3200C Disable Enable Disable Record Enable Record Delay 10 seconds Relay out Enable Item Disconnectio n Relay Delay IP Conflict Disable Record Enable Record Delay 10 seconds Relay out Enable Storage Storage Record Control General System Local Host Date time and out IPCHFW3101C 10 seconds Enable Relay Delay FTP out IPCHFW3100C 10 seconds Enable FTP Disable Server IP N/A Port 21 Username anonymity Password N/A Re
Setup DST Default Setup IPCIPCHFW3300C HFW3200C Disable DST Type Week Start Time 00:00:00 of the first Sunday of the month End Time 00:00:00 of the second Monday of the month NTP Disable NTP Server clock.isc.
2 Structure 2.1 Multiple-function Combination Cable You can refer to the following figure for multiple-function combination cable information. See Figure 2-1. Figure 2-1 Please refer to the following sheet for detailed information. Port Name Function Connection Note VIDEO OUT Video port output BNC Output analog video signal. It can connect to the TV monitor to view the video. AUDIO IN Audio port input RCA Input audio signal. It can receive the analog audio signal from the pickup.
Port Name SN Name Note 1 ALARM_COM Alarm output public port. 2 ALARM_NO Alarm output port. It is to output the alarm signal to the alarm device. NO: normal open alarm output port. It works with the ALARM_COM port. I/O Port 3 ALARM_IN1 Alarm input port 1. It is to receive the on-off signal from the external alarm source. 4 ALARM_IN2 Alarm input port 2. It is to receive the on-off signal from the external alarm source. 5 GND Ground port 2.
2.3 Bidirectional talk 2.3.1 Device-end to PC-end Device Connection Please connect the speaker or the MIC to the audio input port of the device. Then connect the earphone to the audio output port of the PC. Login the Web and then click the Audio button to enable the bidirectional talk function. You can see the button becomes orange after you enabled the audio talk function. Click Audio button again to stop the bidirectional talk function.
Figure 2-4 Please refer to the following figure for alarm input information. See Figure 2-5. Alarm input: When the input signal is idle or grounded, the device can collect the different statuses of the alarm input port. When the input signal is connected to the 5V or is idle, the device collects the logic “1”. When the input signal is grounded, the device collects the logic “0”. Figure 2-5 Please refer to the following figure for alarm output information. See Figure 2-6.
3 Device Installation Please follow the steps listed below to install the device. Please refer to Figure 3-1 for reference. z Please draw the installation holes in the installation surface and then mark three expansion bolts holes in the surface. Insert three bolts in the hole and secure firmly. z Please line up the installation holes of the bottom of the pendant mount bracket to the installation holes in the surface. Then insert the three bolts to the holes of the bottom of the bracket.
4 Quick Configuration Tool 4.1 Overview Quick configuration tool can search current IP address, modify IP address. At the same time, you can use it to upgrade the device. Please note the tool only applies to the IP addresses in the same segment. 4.2 Operation Double click the “ConfigTools.exe”icon, you can see an interface is shown as in Figure 4-1. In the device list interface, you can view device IP address, port number, subnet mask, default gateway, MAC address and etc.
Select the “Open Device Web” item; you can go to the corresponding web login interface. See Figure 4-3. Figure 4-3 If you want to modify the device IP address without logging in the device web interface, you can go to the configuration tool main interface to set. In the configuration tool search interface (Figure 4-1), please select a device IP address and then double click it to open the login interface. Or you can select an IP address and then click the Login button to go to the login interface.
Figure 4-5 18
5 Web Operation This series IPC product support the Web access and management via PC. Web includes several modules: monitor channel preview, PTZ control, system configuration, alarm and etc. 5.1 Network Connection Please follow the steps listed below for network connection. z Make sure the IPC has connected to the network properly. z Please set the IP address, subnet mask and gateway of the PC and the IPC respectively. IPC default IP address is 192.168.1.108. Subnet mask is 255.255.255.0. Gateway is 192.
Figure 5-2 If it is your first time to login in, system pops up warning information to ask you whether install control webrec.cab or not after you logged in for one minute. Please click OK button, system can automatically install the control. When system is upgrading, it can overwrite the previous Web too. If you can’t download the ActiveX file, please check whether you have installed the plug-in to disable the control download. Or you can lower the IE security level. See Figure 5-3.
Figure 5-4 Please refer to the Web Operation Manual included in the resource CD for detailed operation instruction.
6 FAQ Bug I can not boot up the device. Please click RESET button for at least five seconds to restore factory default setup. SD card times Do not set the SD card as the storage media to storage the schedule record file. It may damage the SD card duration. write I can not use the disk as the storage media. When disk information is shown as hibernation or capacity is 0, please format it first (Via Web). I can not upgrade the device via network.
Appendix Toxic or Hazardous Materials or Elements Component Name Toxic or Hazardous Materials or Elements Pb Hg Cd Cr VI PBB PBDE Circuit Board Component ○ ○ ○ ○ ○ ○ Device Construction Material ○ ○ ○ ○ ○ ○ Wire and Cable ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Packing Components Accessories O: Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ/T11363-2006 standard.
