Mini IP Dome Camera User’s Manual Version 1.0.
Welcome Thank you for purchasing our IP camera! This user’s manual is designed to be a reference tool for your system.
Important Safeguards and Warnings 1．Electrical safety All installation and operation here should conform to your local electrical safety codes. The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited power source is rated 12V DC in the IEC60950-1. We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation. We are not liable for any problems caused by unauthorized modification or attempted repair.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the device. Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera. 7. Accessories Be sure to use all the accessories recommended by manufacturer. Before installation, please open the package and check all the components are included.
Table of Contents 1 General Introduction ..................................................................................................................1 1.1 Overview ........................................................................................................................1 1.2 Features.........................................................................................................................1 1.3 Specifications ............................................................
1 General Introduction 1.1 Overview This series IP camera integrates the traditional camera and network video technology. It adopts audio and video data collection, transmission together. It can connect to the network directly without any auxiliary device. This series IPC uses standard H.264 video compression technology and MJPEG audio compression technology, which maximally guarantee the audio and video quality.
z z z z Day/Night mode auto switch. Backlight compensation: screen auto split to realize backlight compensation to adjust the bright. Support electronic shutter and gain setup. Support video watermark function to avoid vicious video modification. 1.3 Specifications 1.3.1 Performance System Please refer to the following sheet for IPC performance specification.
Video Motion Detect Video Loss Alarm Input Record and Backup Record Priority 396 (18*22) detection zones；sensitivity level ranges from 1 to 6 (The 6th level has the highest sensitivity) Activation event: Video storage, image snapshot, log, email SMTP function and etc. Activation event: Video storage, image snapshot, log, email SMTP function and etc.
Function Setup Type Default setup Item IPC-HDB3200CP(N) Series Flip Disable Video Main stream Video stream bit Extra stream Snapshot Overlay Path Bit stream type General Encode mode H.264B Resolution 1080P（1920*1080） Frame rate （FPS） PAL: 25 NTSC:30 Bit stream type CBR Reference bit rate 3584-8192 Kb/S Bit rate 8192 I frame interval 50 Watermark settings Enable Watermark character DigitalCCTV Enable Enable Bit stream type General Encode mode H.
Function Setup Type Default setup Item IPC-HDB3200CP(N) Series Host name IPC Ethernet card Wire(Default) Mode Static MAC address Depends on the device IP version IPV4 IP address 192.168.1.168 Subnet mask 255.255.255.0 Default gateway 192.168.1.1 Preferred DNS 8.8.8.8 Alternate DNS 8.8.8.
Function Setup Type Default setup Item IPC-HDB3200CP(N) Series Authenticatio n (Encrypt mode) N/A Title (Subject) IPC Message Main Receiver N/A Interval 0s Health email Disable ，interval=60m Enable UPnP Disable SNMP v1 Disable SNMP v2 Disable SNMP port 161 Read community public Write community private Trap address N/A Trap port 162 Enable Enable Server name “Device name+SN”. Depends on the device. Multicast address 239.255.42.
Function Setup Type Default setup Item IPC-HDB3200CP(N) Series Disable Record Channel Enable Record Delay 10 seconds Send email Disable Snapshot Disable No SD card Enable Disable Send email Disable Capacity warning Enable Disable Capacity limit (Space threshold) 10% Send email Disable Enable Disable Send email Disable Disconn ection Enable Disable Record Enable Record delay 10s IP conflict Enable Disable Record Enable Record delay 10s FTP enable Disable Server IP
Function Setup Type Default setup Item Conditions control) IPC-HDB3200CP(N) Series (Record Local setup Date and time General setup System management Auto maintenance Remote storage path N/A Pack duration 8m Pre-record 5s Disk full Overwrite Record mode Auto Device name Device factory SN Language English Video standard NTSC Date format Y-M-D Time format 24H Time zone GMT+08:00 Current time Sync PC DST Disable DTS type Week Start time 00:00:00 of the first Sunday of the m
2 Framework 2.1 Dimensions Please refer to the following figure for the dimension information. The unit is mm. See Figure 2-1 through Figure 2-3.
Figure 2-3 2.2 Structure Please refer to the following figure for detailed information. See Figure 2-4. Figure 2-4 Please refer to the following sheet for detailed information.
SN Name 1 X-Y-Z rotation module 2 Device lens 3 Dome camera enclosure 4 Power input port Connect to the DC 12+ power to input the power. 5 Network port Network data input, output and PoE.
3 Installation 3.1 Device Installation This series IPC can be put on the table to realize surveillance. Or you can use the bracket or the inceiling installation to realize the hang function. Please refer to the steps listed below. Figure 3-1 Figure 3-2 Step1 Use the inner hexagonal wrench (provided) to loose the three inner hexagon screws in the dome cover and then open the cover.
the cable from the side port of the cable channel when you are installing the device cable. And then you can draw out the cable from the cable channel of the pedestal. Step 3 Adjust the device installation pedestal to the proper position and then draw the cable through the cable exit you just dug in the ceiling (wall).
Step 1 Please refer to the step 1 in chapter 2.1 to open the device. Step 2 Find the “SD CARD” indicator in the enclosure. Adjust the SD card to the proper direction and then install. See Figure 3-4. Step 3 Please refer to the step 5 in chapter 2.1 to complete the installation.
4 Quick Configuration Tool 4.1 Overview Quick configuration tool can search current IP address, modify IP address. At the same time, you can use it to upgrade the device. Please note the tool only applies to the IP addresses in the same segment. 4.2 Operation Double click the “ConfigTools.exe’” icon, you can see an interface is shown as in Figure 4-1. In the device list interface, you can view device IP address, port number, subnet mask, default gateway, MAC address and etc.
Select the “Open Device Web” item; you can go to the corresponding web login interface. See Figure 4-3. Figure 4-3 If you want to modify the device IP address without logging in the device web interface, you can go to the configuration tool main interface to set. In the configuration tool search interface (Figure 4-1), please select a device IP address and then double click it to open the login interface. Or you can select an IP address and then click the Login button to go to the login interface.
Figure 4-5 17
5 Web Operation This series IPC product support the Web access and management via PC. Web includes several modules includes monitor channel preview, PTZ control, system configuration, alarm and etc. IP camera factory default setup: z IP address: 192.168.1.108. z User name: admin z Password: admin 5.1 Network Connection Please follow the steps listed below for network connection. z Make sure the IPC has connected to the network properly.
Figure 5-2 If it is your first time to login in, system pops up warning information to ask you whether install control webrec.cab or not after you logged in for one minute. Please click OK button, system can automatically install the control. When system is upgrading, it can overwrite the previous Web too. If you can’t download the ActiveX file, please check whether you have installed the plug-in to disable the control download. Or you can lower the IE security level. See Figure 5-3.
Figure 5-4 Please refer to the Web Operation Manual included in the resource CD for detailed operation instruction.
6 FAQ Bug I can not boot up the device. Please click RESET button for at least five seconds to restore factory default setup. SD card times Do not set the SD card as the storage media to storage the schedule record file. It may damage the SD card duration. write I can not use the disk as the storage media. When disk information is shown as hibernation or capacity is 0, please format it first (Via Web). I can not upgrade the device via network.
Appendix Toxic or Hazardous Materials or Elements Component Name Toxic or Hazardous Materials or Elements Pb Hg Cd Cr VI PBB PBDE Circuit Board Component ○ ○ ○ ○ ○ ○ Device Construction Material ○ ○ ○ ○ ○ ○ Wire and Cable ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Packing Components Accessories O: Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ/T11363-2006 standard.
