3-inch 2 Megapixel Intelligent Network Speed Dome Installation Manual Version 1.0.
Table of Contents 1 INTELLIGENT SPEED DOME INSTALLATION PREPARATION ....................... 1 1.1 Basic Requirement ................................................................................................................................ 1 1.2 Check installation space and installation location intension ........................................................... 1 1.3 Please keep all package material well for future use .......................................................................
4.2 Installation ............................................................................................................................................... 7 4.2.1 Installation Requirements ................................................................................................................ 7 4.2.2 Installation Steps ...............................................................................................................................
Welcome Thank you for purchasing our speed dome! Please read the following safeguards and warnings carefully before you install or use the product! iii
Important Safeguards and Warnings Safety Measures 1. Qualified Engineer Needed The installation engineer or maintenance engineer shall have corresponding CCTV system installation certificate or maintenance qualification certificate. The installation engineer or maintenance engineer shall have qualification certificate for work at height.
7. All the examination and repair work should be done by the qualified service engineers. We are not liable for any problems caused by unauthorized modifications or attempted repair. Note 1. Safety Transportation Heavy stress, violent vibration or water splash are not allowed during transportation, storage and installation. This series product must use split type package during the transportation.
Do not use gasoline, dope thinner or other chemical material to clean the shell. It may result in shell transfiguration or paint flake. Do not allow the plastic or rubber material to touch the shell for a long time. It may result in paint flake.
1 INTELLIGENT SPEED DOME INSTALLATION PREPARATION 1.1 Basic Requirement All installation and operation here should conform to your local electrical safety codes. Before installation, please open the package and check all the components are included. Please make sure the speed dome installation environment and installation mode can meet your requirement. If there is special requirement, please contact your local retailer for more information.
2 SETUP BEFORE INSTALLATION 2.1 Check Accessories Before the installation, please check the accessories one by one according to the packing list. Please make sure all the components listed are included. 2.2 Open Device Remove the package and then take out the device. Open the transparent cover and take out the packing material EPE around the speed dome driver. Please remove the dustproof paster from the pedestal. See Figure 2-1. Figure 2-1 2.
Figure 2-2 2.4 TF Card Slot and Reset Button TF card slot and RESET button is shown as in Figure 2-3. Press the RESET button for at least five seconds; you can restore factory default setup. Before you remove the SD card, please make sure it is not in read/write status; otherwise you may lose data or result in SD card damage.
3 CEILING INSTALLATION 3.1 Installation Components The ceiling installation dome body is shown as in Figure 3-1. Figure 3-1 3.2 Ceiling Installation Steps 3.2.1 Installation Requirements The ceiling mount speed dome can be installed in the hard construction wall in the indoor environments. Before the installation, please make sure: The wall is thick enough to install the expansion bolt. The wall can at least sustain the 8x weight of the speed dome. 3.2.
Figure 3-2 Figure 3-3 3.2.3 Cable Connection The step listed below is for ceiling or wall mount series product.
Please refer to Figure 3-4 to connect the power cable, network cable, audio cable, alarm input/output pin of the intelligent speed dome composite cable according to your actual requirements. Pleas use insulation tape to seal the cable connection ports to do proper waterproof work. The audio input and output port are standard RCA port and power port is standard DC5.5*2.1F port.
4 WALL MOUNT BRACKET INSTALLATION 4.1 Component Installation Wall mount bracket is shown as below. See Figure 4-1. Figure 4-1 4.2 Installation 4.2.1 Installation Requirements The wall mount speed dome can be installed in the hard construction wall in the indoor environments. Before the installation, please make sure: The wall is thick enough to install the expansion bolt. The wall can at least sustain the 8x weight of the speed dome. 4.2.2 Installation Steps 1).
Figure 4-2 2). Connect the adapter block to the internal thread of the wall mount bracket. Pull the intelligent speed dome composite cable through the adapter block and end of the column of the wall-mount bracket and pull it out of the other end of the wall mount bracket. Line up the pedestal to the internal hole of the adapter block. Insert four screws and rubber washer. See Figure 4-3.
Figure 4-4 9
5 APPENDIX Ⅰ 24V AC WIRE GAUGE AND TRANSMISSION DISTANCE RELATIONSHIP SHEET The recommended max transmission distance is under the following environments: The wire diameter is fixed and the DC 24V power voltage loss rate is below 10%. For the device of DC power supplying, the max allowed voltage loss rate is 10%. Please refer to the bold line (The second line) in the following sheet for 24V AC wire gauge and transmission distance relationship. Feet(m) mm 0.8000 1.000 1.250 2.
6 APPENDIX Ⅱ 12V AC WIRE GAUGE AND TRANSMISSION DISTANCE RELATIONSHIP SHEET The recommended max transmission distance is under the following environments: The wire diameter is fixed and the DC 12V power voltage loss rate is below 10%. For the device of DC power supplying, the max allowed voltage loss rate is 10%. Please refer to the bold line (The first line) in the following sheet for 12V AC wire gauge and transmission distance relationship. Feet(m) mm 0.8000 1.000 1.250 2.
7 APPENDIX III WIRE GAUGE REFERENCE SHEET Metric bare wire diameter （mm） 0.050 0.060 0.070 AWG SWG 43 42 41 47 46 45 Bare wire cross section （mm2） 0.00196 0.00283 0.00385 0.080 0.090 40 39 44 43 0.00503 0.00636 0.100 0.110 0.130 38 37 36 42 41 39 0.00785 0.00950 0.01327 0.140 0.160 35 34 37 0.01539 0.02011 0.180 0.200 0.230 33 32 31 35 0.02545 0.03142 0.04115 0.250 0.290 30 29 33 31 0.04909 0.06605 0.330 0.350 0.400 28 27 26 30 29 28 0.08553 0.09621 0.1257 0.450 0.
owners. If there is any uncertainty or controversy, please refer to the final explanation of us. Please visit our website or contact your local service engineer for more information.
