Installation Manual GEMU090 Series Ice-O-Matic 11100 East 45th Ave Denver, Colorado 80239 P tN Part Number b 9081430-01 9081430 01 / 17-3371-01 17 3371 01 Date D t 9/11
Ice-O-Matic Parts and Labor Domestic & International Limited Warranty Mile High Equipment LLC (the “Company”) warrants Ice-O-Matic brand ice machines, ice dispensers, remote condensers, water filters, and ice storage bins to the end customer against defects in material and factory workmanship for the following: Cube ice machines, compressed ice machines and remote condensers.
GEMU090 Installation and Use Introduction This manual includes information for the installation, operation and maintenance of the GEMU090 residential ice machine. The GEMU090 was developed to offer fans of Ice-O-Matic’s Pearl Ice form the ability to have that ice in their homes. Previously pearl Ice was only available in commercial establishments, where it developed a strong following because of the chewable nature of the ice.
GEMU090 Installation and Use Product Description: This ice machine is designed to be used indoors, in Water Quality a controlled environment or outdoors within certain limits. The water to the machine must be potable, or fit for human consumption. Beyond that, water supplies The GEMU090 is made up of two major systems: vary in the degree of mineral content. As this ice the ice making system and the ice storage system.
GEMU090 Installation and Use Cabinet Dimensions FLOOR DRAIN ACCESS HOLE 3 7/8" 20 3/4" 2 3/4" 1/4" O.D. COPPER WATER INLET COMPRESSION FITTING PROVIDED 3/4" 1 5/8" HANDLE 22 3/8" 14 7/8" 5 1/8" 33 3/8" MIN. 34 3/8" MAX. 29 1/2" 3 7/8" 2 1/2" 3 1/4" 115V POWER CORD 7 1/2" AIR OUT 1" LEG ADJUSTMENT (4) PLACES AIR IN LEFT SIDE SVC. ACCESS PANEL 11 5/8" DRAIN ACCESS - FLEXIBLE TUBING 3/8" I.D. PUMP MODEL (INCLUDED) 5/8" I.D.
GEMU090 Installation and Use Location Recommendations: The machine can be built into a cabinet. It is an air cooled refrigeration system and so air flows in and out of it through the grill at the bottom front. The grill must not be blocked by any covering door or other obstruction. Drain Conversion: A gravity drain model can be converted to a drain pump model by installing a drain pump kit. The drain pump kit consists of a drain pump, wiring harness and associated tubing. The part number is KPU090.
GEMU090 Installation and Use Familiarization The control panel is visible when the door is opened. It has three indicator lights and two switches. Ice Making Check Water Time to Clean Clean Reset Control Panel The model and serial number plate is located on the bottom of the control panel box. The Bin Light and Ice Level Sensor are also visible from that angle, as is the Ice Chute.
GEMU090 Installation and Use l Door Swing The door can be attached to open with hinges on the left or right. Retain all screws for re-use. 6. Remove original bottom hinge. To change: 1. Remove top hinge pin from hinge. 7. Remove two plugs or screws from upper cabinet bracket. 8. Attach bottom hinge to upper cabinet bracket using the original screws. 9. Place the door on bottom hinge, tip up to slide under top hinge. 2. Tilt top of door away from cabinet and lift door off bottom hinge. 10.
GEMU090 Installation and Use Plumbing - Pump Model Drains Water Supply There are two types of ice machine models, one that drains by gravity and one that has an internal drain pump. The recommended water supply tubing is ¼ inch OD copper. Stainless steel flex or reinforced PCV tube may also be used. Install an easily accessible shut-off valve between the supply and the unit. This shut-off valve should not be installed behind the unit. Drain Pump Model drain installation 1.
GEMU090 Installation and Use Plumbing: Gravity Drain Model clamp. Leave the other end of the tube lying on the floor of the base pan until the unit is positioned over the floor drain. Caution: Restrictions in the drain system to the machine will cause water to back up into the ice storage bin and melt the ice. Gravity drain tubing must be vented, have no kinks and slope to the building drain. Air gaps are typically required by local code. 1. Place the ice machine in front of the installation opening.
GEMU090 Installation and Use Electrical and Start Up The ice machine is supplied with a power cord. Do not remove the grounding pin from the cord’s plug. Do not use extension cords. Follow all codes. Connect the machine to its own 115 volt, 15 amp circuit. Installation check list: 1. Has the unit been connected to the proper water supply? 2. Has the water supply been checked for leaks? 1. If the electrical outlet for the ice maker is behind the unit, plug in the unit. 3.
GEMU090 Installation and Use Use No special instructions are needed for use. Just take as much ice as you need, the machine will replace it. A scoop is provided, and it can be stored in the machine using the loop of tubing on the right side as a holder. Noise: The machine can be shut off anytime by just pushing and releasing the On/Off button. Ice Making What shouldn’t be done? Never keep anything in the ice storage bin that is not ice.
GEMU090 Installation and Use Maintenance Ice-O-Matic strongly recommends regular maintenance of this ice machine. During normal operation mineral scale that is in the water supply will gradually build up on the ice making surfaces. That build up can cause excessive loading of the ice making system, which can cause premature failure. Regular removal of the mineral scale will lengthen the product’s life. 4. Return the kickplate and front service panel to their original positions.
GEMU090 Installation and Use How to remove scale from the ice making system. Cleaning this machine involves adding a solution of scale remover and water to the ice machine and continuing to add it as it makes ice. The scale remover must be diluted to the correct ratio. A squirt bottle will make adding the scale remover much easier when the unit is built in. If not built in, remove the top panel for reservoir access. Float Valve On/Off Lever Recommended tools: Rubber gloves, squirt bottle & scale remover.
GEMU090 Installation and Use 6. Locate blue float valve on/off lever. Move lever up about half way to shut water off. 8. Obtain pre-mixed Ice-O-Matic Clear 1 Scale remover solution (with squirt bottle) or mix a solution of Clear 1 with water: 2.5 ounces of Clear 1 with 1 quart (32 oz) of warm water. Ice machine scale remover contains acids. Acids can cause burns. If concentrated cleaner comes in contact with skin, flush with water. If swallowed, do NOT induce vomiting. Give large amounts of water or milk.
GEMU090 Installation and Use 11. Press and HOLD both the Clean-Reset and On/Off buttons for 5 seconds. The Time to Clean light will blink on and off. 14. Return the reservoir cover to its original position. Press Both Ice Making Check Water 13a: Optional - move float lever up to Off, add locally approved sanitizer* to water system, then repeat step 13. Move the float lever down to On. Time to Clean 15.