Installation, Start-Up and Maintenance Manual ICE SERIES CUBERS ICE0250 through ICE2100 Series* ICEU150, ICEU220 and ICEU300 Undercounter Series* ICE0320 and ICE0520 22 Inch Series* *INCLUDES 230/50/1 VOLT UNITS Ice-O-Matic 11100 East 45th Ave Denver, Colorado 80239 Part Number 9081264-01 Date 11/08
*
ICE Series Introduction How To Use This Manual Ice-O-Matic provides this manual as an aid to the service technician in installation and maintenance of the ICE Series (electro-mechanical) cube ice machines. Do not attempt to perform installation, start-up or maintenance unless you have read and fully understand this manual. If at any time you encounter conditions that are not addressed in this manual, call, E-mail or write the Ice-O-Matic Service Department: Ice-O-Matic th 11100 E. 45 Ave. Denver, Co.
ICE Series Table of Contents Introduction Page i Table of Contents Page ii Freight Claim Procedure Page iii Warranty Page iv Model Number and Serial Number Format Page 1 Installation Guidelines Page 2 Remote Condenser Guidelines Page 4 Electrical and Plumbing Requirements Page 6 How the Machine Works Page 13 Start-Up Procedure Page 14 General Maintenance Page 16 Cleaning Procedure Page 17 Cabinet Care Page 18 Winterizing Procedure Page 19 Maintenance Record Page 20 Page ii
ICE Series Freight Claim Procedure Freight Claims Important! Inspect Promptly This merchandise has been carefully inspected and packed in accordance with the carrier’s packing specifications. Responsibility for safe delivery has been assumed by the carrier. If loss or damage occurs, you as the consignee must file a claim with the carrier and hold the container for carrier’s inspection.
ICE Series Warranty Ice-O-Matic Parts and Labor Domestic & International Limited Warranty Mile High Equipment LLC (the “Company”) warrants Ice-O-Matic brand ice machines, ice dispensers, remote condensers, water filters, and ice storage bins to the end customer against defects in material and factory workmanship for the following: • Cube ice machines,”GEM” model compressed ice machines ,” MFI” model flake ice machines and remote condensers.
ICE Series Model and Serial Number Format Model and Serial Number Format Note: Sample of Serial Number Data Plate The serial number format and machine specifics are detailed on the data plate. ICE 040 0 H A 2 Design Level Condenser Type: A=Air, W=Water, R=Remote Cube Size: H=Half, F=Full Voltage: 0=115V, 6=230V/60Hz. 5=240V/50Hz.
ICE Series Installation Guidelines Installation Guidelines For proper operation of the Ice-O-Matic ice machine, the following installation guidelines must be followed. Failure to do so may result in loss of production capacity, premature part failures, and may void all warranties. Reference the installation parameters prior to installing the machine: Ambient Operating Temperatures Minimum Operating Temperature: 50°F (10°C) Maximum Operating Temperature 100°F (38°C), 110°F (43°C) on 50 Hz. Models.
ICE Series Installation Guidelines Secure the machine on top of the bin or dispenser. Attach the ice machine to the bin with the mounting straps provided with the bin or dispenser. Insure that the back of the ice machine is flush with the back of the bin. Proper functioning of the bin door requires the bin door, when it is opened, to be in a stable position. If the ice machine is too far forward on the bin, the opened door may not be stable, resulting in an unexpected closing of the bin door.
ICE Series Remote Condenser Guidelines Remote Condenser Installation For proper operation of the Ice-O-Matic ice machine, the following installation guidelines must be followed. Failure to do so may result in loss of production capacity, premature part failure, and may void all warranties. Use the following for planning the placement of the remote condenser relative to the ice machine.
ICE Series Remote Condenser Guidelines The following remote ice makers incorporate the mixing valve in the condenser. This configuration allows up to a 100 foot calculated remote line set run. Reference the diagram below to calculate the maximum 100 foot line set run.
ICE Series Electrical and Plumbing Requirements Electrical and Plumbing Requirements: ICEU150, 220, 225 and 226 31.00 Note: The ICEU150, 220, 225 and 226 do not have a splash curtain. These models utilize a thermostatic bin control in place of a mechanical bin switch. ON-OFF-WASH Switch is located in the control box. Remove the grill screws to access the control box.
ICE Series Electrical and Plumbing Requirements Electrical and Plumbing Requirements: ICEU300 and 305 Note: The ICEU300 and 305 do not have a splash curtain. These models utilize a thermostatic bin control in place of a mechanical bin switch. ON-OFF-WASH Switch is located in the control box. Remove the grill screws to access the control box.
ICE Series Electrical and Plumbing Requirements Electrical and Plumbing Requirements: ICE0250, ICE0400, ICE0500 and ICE0600 Page 8
ICE Series Electrical and Plumbing Requirements Electrical and Plumbing Requirements: ICE0800 and ICE1000 Page 9
ICE Series Electrical and Plumbing Requirements Electrical and Plumbing Requirements: ICE1400, ICE1800 and ICE2100 Page 10
ICE Series Electrical and Plumbing Requirements Electrical and Plumbing Requirements: ICE0320 and ICE0520 Page 11
ICE Series Electrical and Plumbing Requirements Electrical and Plumbing Requirements: ICE1506 Remote Page 12
ICE Series How the ICE Machine Works How the ICE Machine Works A general description of how the ICE Series cubers works is given below. With the ICE/OFF/WASH switch in the ICE position, the compressor, water pump and condenser fan motor (when applicable) will energize starting the freeze cycle. During the freeze cycle, water is circulated over the evaporator(s) where the ice cubes are formed.
ICE Series Start-Up Procedure Start-Up Procedure Before starting the machine, make sure the machine is level within 1/8 inch in all directions, the bin or dispenser leg height can be adjusted by rotating the leg foot. Check the water level in the water trough. It should be approximately ½ inch above the top of the water pump impeller housing. The water level can be adjusted by bending the float arm. Move the ICE-OFF-WASH switch to the ICE position. The switch is located in the control box.
ICE Series Start-Up Procedure Bin Control Operation The bin control is used to shut the machine off when the bin fills with ice. The bin control must be checked upon installation or initial start-up and when performing maintenance. Adjustments are not covered under warranty. There is one bin switch for each evaporator. The actuator arm of the bin switch comes in contact with the splash curtain. When the bin is full of ice, the splash curtain is held open when ice drops off of the evaporator.
ICE Series General Maintenance Electrical shock and/or injury from moving parts inside this machine can cause serious injury. Disconnect electrical supply to machine prior to performing any adjustments or repairs. Failure to perform the required maintenance at the frequency specified will void warranty coverage in the event of a related failure.
ICE Series Cleaning Procedure ICE Machine Cleaning and Sanitizing Instructions It is the USER’S RESPONSIBILITY to see that the unit is properly maintained. It is always preferable and less costly in the long run, to avoid possible down time by keeping it clean and adjusted as needed; and by replacing worn components before they can cause failure. The following is a list of recommended maintenance that will help keep the machine running with a minimum of problems.
ICE Series Cabinet Care Cleaning stainless steel Commercial grades of stainless steel are susceptible to rusting if not properly maintained. It is important that you properly care for the stainless steel surfaces of your ice machine and bin to avoid the possibility of rust or corrosion. Use the following recommended guidelines for keeping your stainless steel looking like new: 1. Clean the stainless steel thoroughly once a week. Clean frequently to avoid build-up of hard, stubborn stains.
ICE Series Winterizing Procedure Winterizing Procedures Important! Whenever the ice machine is taken out of operation during the winter months, the procedure below must be performed. Failure to do so may cause serious damage and will void all warranties. 1. Turn off water to machine. 2. Make sure all ice is off of the evaporator(s). If ice is being made, initiate harvest or wait for cycle completion. 3. Place the ICE/OFF/WASH switch to the “OFF” position. The switch is located in the control box. 4.
ICE Series Service History Service History Model Number__________________Serial Number__________________Date Installed__________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ _________________
