i Wash §-11 Electronic Bidet Seat INSTALLATION & CARE GUIDE Read all operating instructions before installation and use. Please save this instruction manual and place in an easily accessible location. External appearance and specifications are subject to change for improvement of product without notice.
Il CER A IMPORTANT SAFETY INSTRUCTIONS When using electronic appliances, especially when children are present, basic safety precautions should always be followed. READ ALL INSTRUCTIONS BEFORE USE DANGER As with most electronic appliances, electrical parts are live even when the appliance Is powered off. To reduce risk of death by electric shock: . Do not use while bathing. . Do not place or store appliance where it can fall or be pulled into a tub or sink.
Il CER A CONSIGNES DE SÉCURITÉ IMPORTANTES Lors de Utilisation d’appareils électroniques, en particulier en présence d’enfants, des précautions de sécurité de base doivent toujours &tre respectées. LISEZ TOUTES LES INSTRUCTIONS AVANT UTILISATION DANGER Comme avec la plupart des appareils électroniques, les pinces électriques sont sous tension mérisme lorsque Appareiller est hors tension. Pour réduire le risque de décès par choc électrique: 1. Ne pas utiliser pendant le bain. 2.
| CER & SAFETY PRECAUTIONS For your own safety, follow all precautions in this manual. Caution: In order to avoid hazard due to inadvertent resetting of the thermal cutout, this appliance must not be attached to an external switching device, such as a timer, nor should it be connected to a circuit that is regularly switched on and off by utility.
SAFETY PRECAUTIONS Do not get any water or cleaning products on the main unit or power plug. Doing so may cause a fire, electrical shock, heat or a short. Doing so can cause the product to crack _resulting in injury or water damage. Always unplug the product from the outlet i apply when using the Nozzle Clean function. before cleaning or maintenance. Failure to do could cause electrical shock. This does not Do not do anything that could damage the power cord or power plug.
SAFETY PRECAUTIONS BEWARE OF LOW-GRADE BURNS. Improper use of a heated seat could cause a low grade burn. When sitting on the toilet seat for long periods of time, switch the toilet seat temperature to OFF. Always connect the product to the cold water supply. Connecting to hot water supply may result in burns or equipment damage.
SAFETY PRECAUTIONS Do not step on or stand on the toilet seat, lid or main unit. Do not apply strong force Do not put anything else into the toilet paper or mechanical shock. Do not place heavy except for toilet paper. Doing so may cause objects on the toilet seat, lid or main unit. product damage from a resulting blockage. Doing so may cause injury or product damage. Do not place hands, fingers or any other object into the warm air outlet.
I CEREBRA GROUNDING INSTRUCTIONS This product should be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escapee wire for the electrical current. The plug must be plugged into an outlet that is properly installed and grounded. /\ DANGER Improper use of the grounding plug can result in electric shock.
| CER X INSTRUCTIONS DE MISE A LA TERRE Ce produit doit &tre mis a la terre. En cas de court-circuit électrique, la mise a la terre réduit le risque de choc électrique en fournissant un fil d’échappement pour le courant électrique. La fiche doit être branchée dans une prise correctement installée et mise a la terre. Une mauvaise utilisation de la fiche de mise a la terre peut entraîner un choc & DANGER électrique.
Il CER A PARTS IDENTIFICATION Seat Cover ey Main Body Power Plug Remote Control Receiver o Stainless Steel Nozzle for larger view.
INSTALLATION INSTRUCTIONS INSTALLING THE MAIN UNIT e Remove the existing toilet seat and lid by unfastening the seat bolts on the underside of the bowl.
i Wash FEATURES & REMOTE GUIDE CERAMIC FRONT VIEW Press once Press to turn on to activate the unit. While the the rear wash. the selected temp or unit is on, press Wash cycle s once to stop any active function. **3 about 3 minutes. LED light bar will indicate pressure levels. Press once to activate the front (feminine) wash. Wash cycle Is about 3 minutes. When Rear or Front ‘Wash cycles are active, press Oscillating and the nozzle will move backwards and o+« forwards fora fuller cleanse.
Il CER WA i Wash SEAT PANEL GUIDE If your i Wash remote is not operational lost, dead batteries, damaged or otherwise not working), the basic wash functions of your bidet seat can be controlled from the seat panel located on the left-side of the seat (when facing the unit from the front). These controls will only activate or stop the spray functions. Temperature, pressure and nozzle position settings cannot be changed using the seat panel controls.
| CER & CLEANING YOUR i Wash For your safety, make sure the unit is powered OFF AND unplugged before cleaning. Turn off the water supply by turning the water supply valve clockwise. Detach the transfer hose from toilet seat to expose the water filter. Clean the filter gently with a soft brush. Re-insert the filter and reattach the transfer hose. Turn the water supply back on by turning the water supply valve counterclockwise.
| CER & CLEANING YOUR i Wash For your safety, make sure the unit is powered OFF AND unplugged before cleaning. * The external casing of the seat is made of a plastic which may be damaged by coarse brushes / pads, harsh chemicals, etc. Test any household cleaner on a inconspicuous area before using. Do not use toluene, mineral oil, heptagon and nitric, chronic or sulfuric acids to clean this product. * Disconnect the power plug before cleaning. Be careful not to splash water onto the plug or outlet.
No power Unit is not plugged in Unit is not turned on. Circuit breaker is switched off Check that the power plug is securely plugged into the outlet. Power on the unit by pressing the POWER MODE button on the seat control panel. Make sure the circuit breaker for the outlet is switched on. Weak water pressure Water pressure is set to a low level. Water filter is clogged. Adjust the water pressure level to a higher setting using the remote control. Clean the water filter. See page 16 for instructions.
Adjust the seat temperature level to a higher setting using Seat temperature is sett a the remote control. P When ECO mode is active, the low level. seat temperature is held at Seat is not Unit is in ECO {energy-saving) 86° F (30° C). Once the seat is warm. mode. occupied, the seat will begin to The seat has been occupied for led, g warm to the last used setting. more than 1 hour. | To protect against low-grade burns, the heated seat will turn off once occupied for 1 hour.
I CER A PRODUCT SPECIFICATIONS Icy el Rated Voltage AC 120V, 50/60Hz Rated Power Consumption 1300w Water Supply System Direct connection with tap water Waterproof Rating IP Power Cord Length 1.
Il CARE WARRANTY INFORMATION 3-YEAR LIMITED WARRANTY For electronic bidet seats and integrated bidet toilet seats, Ceramic provides a warranty against defects in material and workmanship limited to three {3) years from the date of purchase. Scratching, staining, and other effects from chemical use, water, and atmospheric conditions are not considered manufacturing defects but are considered normal wear and tear.