Model:IBT-3 Bluetooth® tower speaker INSTRUCTION MANUAL www.ices-electronics.com READ THIS INSTRUCTION MANUAL BEFORE OPERATING THE APPLIANCE.AND SAVE IT FOR FUTURE REFERENCE.
Thank you for purchasing Tower Speaker Getting started Remove the equipment from the box. Remove packaging and place inside the box to store for future reference and / or use In the box Tower speaker unit Tower stand and screws to attach the unit 3.
Safety instructions When using electrical equipments basic safety precautions should always be followed This equipment is not intended for use by persons (including children)with reduced physical, sensory or mental capabilities or lack of experience or knowledge. They should be given appropriate supervision and instructions to use the equipment by a person responsible for their safety. Ensure the equipment is not too close to heat emitting appliances or placed in direct sunlight.
Description of parts Top panel 1. 2. 3. 4. 5. 6. 7. 8. STANDBY Mode Mute LED display Volume control Play/pause Skip forward Skip backward Front Back panel 1. Speaker 2. Remote Sensor (Point remote to the Remote Sensor) 1. 2. 3. 4. 5. 6. USB port Output DC 5V 2.1A (For Charging only) 3.
Remote Control **Point remote at middle of speaker** 1. STANDBY 2. MP3 mode button 3. Mute button 4. Aux in button 5. FM radio button 6. Bluetooth button 7. Skip backward button 8. Play/Pause button 9. Skip forward 10. Scan button 11. CH12. CH+ 13. Bass+ effect button 14. Bass- effect button 15. Treb+ effect button 16. Treb- effect button 17. Volume+ button 18. Volume- button Setting up the speaker tower -Attaching the base 1. Take the tower body and base carefully out of the packaging. 2.
Power setup Connect the AC/DC adapter to the DC in socket on the speaker back panel and plug the adaptor into the mains socket. Using the remote control The battery To get your remote control working intially, pull the clear tab from the battery compartment located at the bottom of the remote. If your remote becomes intermittent or you find you have to move closer the unit to operate, then probably batteries need to be replaced. To replace batteries, slide the holder out from the base of the remote.
5. If it still doesn't work, please reset the Bluetooth and follow above step again. Notes: 1. When the Bluetooth icon on the display flashes, means the speaker is searching the previous paired device. 2. Press play/pause button and hold for 10 seconds, the Bluetooth icon on the display will flash fast, which means the speaker is ready for being paired. 3. After paired sucessfully, the Bluetooth icon on the display will be on. USB port for charging USB port for charging, does not support any media feature.
Programming & Playing of FM radio presets 1. Follow the steps for Playing the FM Radio. 2. Press "Scan"button on the remote to search and preset stations in memory, (i.e. “P01” – this will blink on the display - and then the preset station frequency number will show on the display). 3. Note: 20 FM stations can be preset. 4. To play the preset Radio Stations, press the "CH-" or "CH+" buttons to cycle through the preset FM radio stations.
Trouble Shooting Before taking the unit to be repaired, please check the following table when a problem occurs. Consult your dealer or service center if the problem cannot be solved with the following information. Problem Power System does not turn on or does not respond to the remote control. Remote control No functions or short range. Remedy -Make sure AC/DC power plug is connected to the wall socket outlet properly and it has power. -If this does not help, leave the unit unplugged before seeking advice.
SPECIFICATIONS Power Operation temperature Speakers Speaker output Subwoofer Speaker Aux-in 1 / Aux Lead Remote Control Unpacked Weight Dimensions (Approx.) 100-240V AC ~50Hz 0°C to + 40°C 4 x 3” speakers + 1 x 4.5” speaker 2 x 10W RMS; 60W p.m.p.o. 1 x 25W 3.5mm dia. / 3.5mm to 3.5mm Aux Lead Battery 3V CR2025 5.6 Kgs Approx. 150x150x990mm NOTE: As a result of continual improvements, the design and specifications of the product within differ slightly from the unit illustrated on the packaging.
Products with the CE marking comply with the EMC Directive (2004/108/EC) and the Low Voltage Directive (2006/95/EC) issued by the Commission of the European Community. Hereby, STL Group BV, Ankerkade 20 NL 5928 PL Venlo, declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The declaration of conformity may be consulted at https://icessupport.zendesk.com/forums/22810983-CE-Documents This product operates at 2400 - 2483.
