A25B15 / A25O15 / A25G15 This machine cannot be used in any other country where the electric voltage for its power supply is not available. ● This product is designed for indoor installation. Please be sure to install it indoors. ● The external appearance, design, color, and components of this machine may be changed without prior notice.
Contents 1. Safety Cautions 2 2 3 Power supply related items 4 Installation related items 5 2. Part names 6 3. Installation specifications 7~8 Gravity Drain Pipe Model 9 Drain Pump Model 10 4. What to check prior to installation 11 5. Installation of the Product 12~13 6. Specific Features 14 7. Guide to Operating the Ice Maker 15~16 8. Washing the Ice Maker 17~20 9. Maintenance of the Ice Maker 21 10. Specifications 22 11.
1. Safety Cautions To prevent any safety-related accident and to ensure convenient usage of this product with better understanding, cautions and warnings are accompanied by symbols and figures. Make sure you understand the symbols and figures below before proceeding. Danger Using the product without taking careful note of this symbol may cause death or serious injury to the user or fire.
■ Power supply related items ■ Oh! NO Avoid putting any object on the power cord and make sure that the cord does not get tangled or tied. It may cause fire or electric shock. Oh! NO Stop using the product if the power cord is damaged. It may cause fire or electric shock. Do not touch any electrical component or the power cord with wet hands. It may cause electric shock. Do not alter the power cord or arbitrarily modify it to connect to an unauthorized power source.
■ Installation related items ■ THINNE R GAS GA SOL LIN Keep away any heating appliance from the power cord. It may melt the coating of the cord, causing fire or electric shock. Do not install the product at a place where moisture or dust gathers easily or where rain or water spatters. It may cause electric shock or fire. Combustible gas or flammable material (benzene, gasoline, thinner, LP gas, etc.) must be kept away from the product and should never be put on the product.
2.
3. Installation specifications Space requirements for installation Fig. 1 Front View When moving the ice maker, check whether the prepared opening dimensions,electric power, and piping position are correct. Refer to the installation specifications and drawings shown on pages 9 and 10. Figures 4, 5, 6 and 7 show the entire dimensions of the product. This product is a gravity drain pipe model that requires a drain pipe to run from the exhaust hole at the back of the product to appropriate drain pipe.
Requirements for plumbing Plan the arrangement of the water supply pipes. Connect a 1/4" diameter copper cable with the tap water pipe. Install a shutoff valve between the tap water pipe and the product so that the user can operate the valve. Do not install the shutoff valve at the back of the product. “Do not use a self-piercing valve. If the tap water has a high level of minerals, a pipeline filter will be required. The pressure of the tap water should be maintained at a level between 20psi (1.
Gravity Drain Pipe Model Before connecting the drain tube and the water supply pipe with the ice maker, pipes should necessarily be arranged. The horizontal distance of the drain tube should be 1/4" at every 12" (305) distance. An air gap is required between the drainage tube of the ice maker and the drain pipe or sewage container. A stand pipe fitted with a trap at the lower part may be used as a drain pipe or sewage container.
Drain Pump Model 1) Arrange the ice maker at the front of the opening of installation. 2) Adjust the horizontality leg so as to meet the height. 3) Install the inlet pipe (copper pipe with a diameter of 1/4”) on the wall and connect the water supply valve. 4) Connect the drain pipe from the wall to the ice maker. Important Information : An air gap may be required between the drain tube of the ice maker and the container of the drain pipe under the provision of local laws and regulations.
4. What to check prior to installation ■ Follow this process! ■ Water source valve 230V~50Hz Water source tube Drain hose - The water supply valve may have different shapes depending on the installation condition. - The filter may be located close to the water source or back of the product depending on the situation. Avoid uneven surface or any place with too much moisture, direct sunlight, too much dust, or spattering water.
5. Installation of the Product Changing Door-opening Method The direction in which the door fixed with hinges opens may be changed. The hinges are attached to the right-hand side of the door when the product is shipped from the factory. However, the ice maker is designed so that the hinges may be installed on either side. If the hinges are moved to the holes on the left-hand side, the door will open to the left.
Installation Checklist Important Information : The installation engineer should check whether any installation part ha been omitted and follow the check list below to ensure safe and proper installation. If you have any questions or problems regarding installation, address your queries to the distributor or dealer. You may also seek information on the company's website. ■ Does the ice maker work properly? If the ice maker does not work, check whether the plug has been inserted properly.
6. Specific Features Fig. 9 Solid figure ■ Sink-Mounted Ice Maker ■T he gravity drain-type naturally drains water, whereas the drain pump-type drains water to an adjacent sink using a built-in pump. ■ A perfect and unified design system with 24" (610) of depth. ■ A decorative door panel may be installed. ■ The product supplies good-quality transparent ice. ■ The maximum capacity of the ice container is 26lbs(12kg). ■ Automatic ice-removal function. ■ Left/Right opening door system.
7. Guide to Operating the Ice Maker Initial operation ① Open the water supply valve connected with the ice maker. ② Insert the plug of the ice maker into the electric outlet. ③ Open the door and turn the switch at the lower end of the product to the “ICE” position.” ④ Discard the first batch of ice. ⑤ Good-quality ice is produced 1-2 hours later. Using the ice maker Use of the ice maker is very simple. Simply turn the switch at the lower end of the product to the “ICE” position.
Operation time It takes about 20-35 minutes to produce a set of 24 ice pieces. The length of one cycle of the ice maker (ice production and ice removal) differs depending upon the cleanness of the ice maker, the surrounding temperature, and the temperature of the water supplied to the ice maker. It takes about 10-12 hours to fill the empty ice container with ice. Ice production The ice production process largely consists of two cycles-ice production and ice removal.
8. Washing the Ice Maker ■ Cleaning the nozzle / ice slide / water tank ■ 1. Open the door and remove two front injection bolts on the top cover. 2. Pull the top cover to remove it. 3. Slightly lift the ice slide to remove it. 4. Clean the slide with soft plastic brush or sponge.
5. Clean the gap of the nozzle frame fixed on the vessel sheet (water tank). 6. Lift the drain projectile inside the vessel sheet (water tank), clean it, and drain the water. * Make sure that the drain projectile is assembled back in the correct position after cleaning; otherwise, draining will not stop, with the product rendered unable to make ice cubes.
2. Open the front door and remove the filter screens from the bottom of the ice tank and water tank. < Water tank > < Ice tank > 3. Rinse the screens with running water, and then assemble them back to the tanks. * Otherwise, the water nozzle will get clogged, or dregs inside the ice tank may damage the product by clogging the draining part. * Insert the bottom filter screen first, followed by the top screen.
■ Cleaning the condenser ■ 1. Remove two screws on the front panel at the center of the inside. 2. Remove dust from the surface of the condenser with a vacuum cleaner for home use or a portable cleaner. 3. Reassemble the screw to the panel after cleaning.
9. Maintenance of the Ice Maker Management in the coldest season ① Clean the ice-production system. ② Turn off the power. ③ Empty the water container. Remove the pump hose. The pump hose may be removed after removing the back panel from the ice maker. ④ Separate the inlet pipe connected with the water supply valve. ⑤ Turn on the power and turn the switch to the “WASH”position to open the water supply valve and to remove the water from the inlet pipe inside the ice maker.
10. Specifications BUILT-IN ICE MAKER Category UNIT Maximum manufacturing capacitor kg/day (at 10 ℃) 29 Dimesion WxDxH (mm) 378 x 624 x 855 (exclude Handle, Leg, Hinge) Quantity of Ice EA 24 Rated Power V/Hz 230 V / 50 Hz Before Box kg 50 After Box kg 63.2 Refrigerant - R-134a Capacity kcal/hr 1065 (at 7.
11. Troubleshooting guide PROBLEM Ice maker does not operate Ice cubes are too large Ice cubes are too small Ice is fragmented. The tank is not fully filled with ice cubes. The ice cubes are white. POSSIBLE CAUSE POSSIBLE SOLUTION Ice maker is unplugged Plug ice maker in. Breaker tripped Reset breaker - if it happens again, call a authorized service center. Switch turned to “OFF” Turn switch to “ICE”. The ice tank is full.
Online Internet Service http://www.icetrousa.
