User's Manual

63
5
FUNCTION FOR RECEIVE
■ Dualwatch operation
Dualwatch monitors 2 frequencies with the same
mode simultaneously.
During dualwatch, both frequencies should be on the
same band, because the bandpass filter in the RF cir-
cuit is selected for the main readout frequency.
q Set a desired frequency.
w Push [DUALWATCH] for 1 sec.
•Equalized receive frequency and “ ” appear in
the LCD. This quick dualwatch function can be turned
OFF in set mode. (p. 98)
•Pushing [DUALWATCH] momentarily activates the du-
alwatch with the previously operated frequency.
e Set another desired frequency using the tuning
dial.
r Adjust [BAL] to set a suitable signal strength bal-
ance between the main and sub readout frequen-
cies.
• S-meter shows the combined signal strength.
t To transmit on the sub readout frequency, push
[CHANGE] or [SPLIT].
RIT function can be used for the main readout only.
∂TX function can be used for the transmit readout
(main readout when the split function is OFF; sub
readout when the split function is ON).
BW
BW
2.4k
2.4k
SFT
SFT
0
FIL2
FIL2
USB
USB
qw:pp
VFO
VFO
TX
TX
56
56
1
USB
USB
USB
USB
USB
USB
FIL2
FIL2
w q .w o p .p p
w q .w o p .p p
14.100.00
14.100.00
14.100.00
14.100.00
VFO
VFO
DUAL-W
DUAL-W
ANT
ANT
1
METER
METER
Po
Po
P.AMP
P.AMP
1
ATT
ATT
OFF
OFF
DUAL-W
DUAL-W
• Scanning during dualwatch
Scanning operates only for the main readout. To op-
erate the scan during dualwatch, scan on the main
readout and use the sub readout for your QSO using
both dualwatch and split frequency operation.
q Program the desired programmed scan edges in
the same amateur band. See p. 78 for program-
ming.
•If you plan to operate a ∂F scan, programming the
scan edges may not be necessary.
w Push [SPLIT] to turn the split frequency function
ON.
•“ ” appears.
e Select VFO mode for the main readout.
r Set the desired operating frequency for the main
readout.
t Push [DUALWATCH] for 1 sec.
•The main and sub readout frequencies are equalized
and the dualwatch function is turned ON.
y Push [(F-4)SCAN] to select the scan screen.
•Push [EXIT/SET] several times to close a multi-func-
tion screen, if necessary.
u Push [(F-1)PROG] or [(F-2)∂F] to start the pro-
grammed scan or ∂F scan, respectively.
•Scan activates on the main readout between the pro-
grammed scan edges or within the ∂F span.
•Transmitting on the sub readout stops the scan.
i To cancel the scan, push [EXIT/SET].
w q .w o p .p p
BWBW
2.4k2.4k
SFTSFT
0
FIL2FIL2
USBUSB
qw:pp
VFOVFO
USB
USB
USBUSB
USB
USB
FIL2
FIL2
w q .w t p .p p
14.100.0014.100.00
14.100.00
14.100.00
VFOVFO
SPLITSPLIT
1
1
DUAL-WDUAL-W
PROGPROG
∂
F
FINEFINE
∂
F SPANF SPAN
SETSET
SCANSCAN
TXTX
ANTANT
1
COMPCOMP
OFF
OFF
WIDE
WIDE
METERMETER
Po
Po
P.AMPP.AMP
1
AGCAGC
MID
MID
ATTATT
OFF
OFF
VOXVOX
OFF
OFF
PROGRAM SCANPROGRAM SCAN
∂ F  SpanSpan: ±±10kHz10kHz
Programmed
Programmed P1:P1: 21.000.00MHz21.000.00MHz
scan
scan edgesedges P2:P2: 21.450.00MHz21.450.00MHz
w q .w o p .p p
BWBW
2.4k2.4k
SFTSFT
0
FIL2FIL2
USBUSB
qw:pp
VFOVFO
USB
USB
USBUSB
USB
USB
FIL2
FIL2
w q .w o p .p p
14.100.0014.100.00
14.100.00
14.100.00
VFOVFO
SPLITSPLIT
1
1
DUAL-WDUAL-W
TXTX
ANTANT
1
METERMETER
Po
Po
P.AMPP.AMP
1
ATTATT
OFF
OFF
BWBW
2.4k2.4k
SFTSFT
0
FIL2FIL2
USBUSB
qw:pp
VFOVFO
USBUSB
USBUSB
USB
USB
FIL2
FIL2
w q .w o p .p p
14.100.0014.100.00
14.100.00
14.100.00
VFOVFO
q r .w p t .p p
SPLITSPLIT
1
1
TXTX
ANTANT
1
METERMETER
Po
Po
P.AMPP.AMP
1
ATTATT
OFF
OFF
SPLIT
SPLIT