User's Manual

90
7
DV MODE PROGRAMMING
7
'ATEWAYR4. EPEATERCALLSIGNPROGRAMMING
When the repeater that was programmed in the pre-
vious item has its own gateway capability, skip this
setting and go to the next item. If the programmed
repeater uses a different gateway repeater, program
gateway repeater’s call sign as described below.
!8 Push [Z](F-2) to display the “GW” item (Gateway
Repeater Call Sign).
s4HEPROGRAMMEDREPEATER’s call sign is displayed, and
“G” is automatically added as, or overwrites, the 8th
digit.
RP–L
GW : JP3YHH G
Ú EDTÙ
!9 Push [EDT](F-4) to enter the repeater call sign pro-
gramming mode.
 s!CURSORAPPEARSANDBLINKS
@0 Push [Ω](F-2) or [≈](F-3) to select the character to
program.
@1 Rotate [MAIN DIAL] to select the first character or
symbol (‘/’ only) to input.
When inputting numbers, push the appropriate key-
pad key.
 s0USH;$%,=&TODELETETHESELECTEDCHARACTERSYM-
bol or number.
 s0USH;30#=&TOINPUTASPACE
s7HENALLCHARACTERSHAVEBEENprogrammed, an error
beep sounds. If you want to reprogram, push [Ω](F-2) or
[≈](F-3) to select a character, then push [DEL](F-4) to
delete it.
@2 Repeat steps @0 through @1 to program a repeater
call sign of up to 8 characters.
 s4HETHDIGITMUSTBEh'v
 s&ORREPEATERSINAZONEWITHNOGATEWAYENTERACOM-
mon name or call sign, up to 7 digits, in all their gateway
repeater cells. The 8th digit must be blank.
@3 Push [MENU] to save the programmed call sign.
R5. EPEATERGROUPPROGRAMMING
4HE)#HASATOTALOFGROUPSn9OUCAN
assign and organize up to 500 repeaters in the 10
groups. Group selection is helpful for quick recall of a
desired repeater.
@4 Push [Z](F-2) to display the “GROUP” item (Re-
peater group).
 s3ELECTEDGROUPNUMBERAPPEARS
RP–L
GROUP:  GRP1

@5 Rotate [MAIN DIAL] to select the desired repeater
group.
!CCESSREPEATERSETTING253%6.
The programmed repeaters can be set as an access
repeater (R1) in the DR mode. To use as R1, the re-
peater frequency, duplex direction and frequency off-
set must be programmed.
@6 Push [Z](F-2) to display the “R1USE” item (Access
Repeater Programming).
 s4HEACCESSREPEATERPROGRAMMINGSCREENAPPEARS
RP–L
R1USE:  YES

@7 Rotate [MAIN DIAL] to select h9%3vORh./v
s7HENh./vISSELECTEDTHEREPEATERCANNOTBESELECTED
as an access repeater (R1) in the DR mode.
s7HENh9%3vISSELECTEDTHEREPEATERCANBESELECTED
as an access repeater (R1) in the DR mode.
± W
hen “NO” is selected in step @7, skip ‘Frequency
programming (FREQ)’ and go to ‘Duplex direction
setting (DUP).’
± 7HENh9%3vISSELECTEDINSTEP@7, push [Z](F-2) to
go to step @8 for the access repeater (R1) program-
ming.
&REQUENCYPROGRAMMING&2%17.
This content appears when “9%3” is selected in “R1
USE,” as described in ‘Access repeater setting (R1
USE)’ above.
@8 Push [Z](F-2) to display the “FREQ” item (Fre-
quency Programming).
 s4HEFREQUENCYPROGRAMMINGSCREENISDISPLAYED
RP–L
FREQ: ..
Ú CLR EDTÙ
@9 Push [EDT](F-4) to enter the frequency program-
ming mode.
 s!CURSORAPPEARSANDBLINKS
RP–L
: ..
ÚÙ
F-INP
#0 Push the keypad key to input the frequency, then
push [F-INP ENT].
s(OLDDOWN;#,2=&FORSECONDTOCLEARTHEDIS-
played frequency.