User's Manual

134
9
GPS/GPS-A OPERATION
9
GPS Auto TX 11. $EFAULT/&&
Select the desired interval from OFF, 5, 10, 30 sec-
onds, 1, 3, 5, 10 or 30 minutes for automatic position
data transmission.
The current position data, received from a GPS re-
ceiver, is transmitted at the selected interval when
“GPS” or “GPS-A” is selected as the “GPS TX Mode”
option as described below.
The GPS message is transmitted as well as the posi-
tion data, if it is programmed.
Even if this setting is set to OFF, you can manually
transmit the position data by pushing [TRANSMIT] or
[PTT] (microphone).
NOTE:
s7HENFOUR'03SENTENCES ARE SELECTED AT THE
same time, “5sec” cannot be selected.
s7HENh-ANUALvISSELECTEDINh-Y0OSITIONvTHE
current position data will not be automatically
transmitted.
GPS TX Mode 12. $EFAULT$ISABLE
Select the GPS or GPS-A operating mode to transmit
the position data from a GPS receiver, or turn OFF the
function.
NOTE: When “GPS” or “GPS-A” is selected, low-
speed data communication cannot be used.
'033ENTENCE2-#13. *
1
$EFAULT/&&
Turn the GPS sentence formatter “RMC” ON or OFF.
'033ENTENCE''!14. *
1
$EFAULT/.
Turn the GPS sentence formatter “GGA” ON or OFF.
'033ENTENCE',,15. *
1
$EFAULT/&&
Turn the GPS sentence formatter “GLL” ON or OFF.
'033ENTENCE'3!16. *
1
$EFAULT/&&
Turn the GPS sentence formatter “GSA” ON or OFF.
'033ENTENCE64'17. *
1
$EFAULT/&&
Turn the GPS sentence formatter “VTG” ON or OFF.
'033ENTENCE'3618. *
1
$EFAULT/&&
Turn the GPS sentence formatter “GSV” ON or OFF.
./4%FOR'03SENTENCES
s5PTOFOUR'03SENTENCESAREUSABLEATTHESAME
time.
s3EEPAGEFOR'03SENTENCESETTINGDETAILS
5NPROTO!DDRESS19. *
2
$EFAULT!0)$34!21
Enter an unproto address of up to 56 characters. The
manually programmed data can be memorized.
s5NPROTOADDRESSPROGRAMMING
q Push [EDT](F-4) to enter the unproto address edit
mode.
w Push [F-1] one or more times to select the desired
character type.
#HARACTERTYPE 3ELECTABLECHARACTERS
ABC A to Z
abc a to z
etc
<" ’ ` ^ + – 1b
( ) [ ] { } ¦ _ ¯ @
e Rotate [MAIN DIAL] to select the first character or
symbol to input.
s7HENENTERINGNUMBERORADECIMALPOINTPUSHTHEAP-
propriate keypad key.
 s0USH;$%,=&TODELETETHESELECTEDCHARACTERSYM-
bol or number.
 s0USH;30#=&TOINPUTASPACE
s7HENALL CHARACTERSHAVEBEENprogrammed, an
error beep sounds. If you want to reprogram, push [Ω]
(F-2) or [≈](F-3) to select a character, then push [DEL]
(F-4) to delete it.
r Push [Ω](F-2) to move the cursor backward, or push
[≈](F-3) to move the cursor forward.
t Repeat steps w through r to program an unproto
address of up to 56 characters.
y Push [MENU] to save the unproto address, and re-
turn to the “SET” screen.
*
1
Appears when “GPS” is selected in “GPS TX Mode.”
*
2
Appears when “GPS-A” is selected in “GPS TX Mode.”