User's Manual

164
14
SET MODE
14
30%%#(,EVEL25. $EFAULT
!DJUSTTHESPEECHAUDIOOUTPUTLEVELTOBETWEEN
NOOUTPUTANDMAXIMUMOUTPUT
30%%#(,ANGUAGE26. $EFAULT%NGLISH
Select English or Japanese as the speech language.
30%%#(3PEED27. $EFAULT()'(
Select HIGH (faster) or LOW (slower) speech speed.
30%%#(3,EVEL28. $EFAULT/.
The signal level announcement with the voice synthe-
sizer can be turned ON or OFF.
s/&&3IGNALLEVELISNOTANNOUNCED/PERATINGFRE-
quency and mode are announced.
s/. 3IGNALLEVELOPERATINGFREQUENCYANDMODE
are announced.
SPEECH [MODE] SW 29. $EFAULT/&&
Turn the Operating Mode Speech function ON or OFF.
When this function is ON, the selected operating mode
is verbally announced when a mode switch is pushed.
s/&&4HEOPERATINGMODE3PEECHFUNCTIONIS/&&
s/. 4HEOPERATINGMODE3PEECHFUNCTIONIS/.
[SPEECH/LOCK] SW 30.
$EFAULT30%%#(,/#+
Select the [SPEECH/LOCK] switch action.
s30%%#(,/#+0USHING THE ;30%%#(,/#+=
switch turns ON the voice synthe-
sizer function.
Holding down the [SPEECH/LOCK]
switch turns the dial lock function
ON or OFF.
s,/#+30%%#(0USHING THE ;30%%#(,/#+=
switch turns the dial lock function
ON or OFF.
Holding down the [SPEECH/LOCK]
switch turns ON the voice synthe-
sizer function.
-EMOPAD.UMBERS31. $EFAULT
Set the number of available memo pads to 5 or 10.
See page 144 for details.
MAIN DIAL Auto TS 32. $EFAULT()'(
Set the Auto Tuning Step function for [MAIN DIAL].
When rapidly rotating [MAIN DIAL], the tuning step au-
tomatically changes as selected.
There are two types of auto tuning steps: LOW (Faster)
and HIGH (Fastest).
s/&& !UTOTUNINGSTEPISTURNED/&&
s,/7 !PPROXIMATELYTIMESFASTER
s()'(!PPROXIMATELYTIMESFASTERWHENTHETUNING
STEPISSETTOK(ZORSMALLERSTEPSAPPROXI-
mately 2 times faster when the tuning step is
set to 5 kHz or larger steps.
-)#5P$OWN3PEED33. $EFAULT()'(
Set the rate at which frequencies are scanned while
holding down the microphone [UP]/[DN] switches.
s,/7,OWSPEEDTUNINGSTEPSSECOND
s()'((IGHSPEEDTUNINGSTEPSSECOND
1UICK2)4#LEAR34. $EFAULT/&&
Select the RIT/∂TX frequency offset clearing opera-
tion with [CLEAR].
s/&&(OLDINGDOWN;#,%!2=FORSECONDCLEARSTHE
RIT and ∂TX frequency offset.
s/. 0USHING;#,%!2=INSTANTLYCLEARSTHE2)4AND
∂TX frequency offset.
!&#,IMIT35. $EFAULT/.
Turn the AFC (Automatic Frequency Control) limit
function ON or OFF.
The AFC function automatically compensates the tun-
ing when a received frequency drifts or goes off fre-
quency.
s/&&4HE!&#FUNCTIONCONTINUESTOTUNEUNTILTHE
displayed frequency changes to reflect the
center of the signal.
s/. 4HE!&#FUNCTIONSTOPSTUNINGWHENTHEFRE-
quency goes off the limited frequency range,
even if received frequency is off frequency.
AFC limit value:
IF Filter width AFC limit value
15 kHz ±10 kHz
10 kHz ±7 kHz
7 kHz ±5 kHz