Operation Manual

4
1
PANEL DESCRIPTION
VVOOXX FFUUNNCCTTIIOONN
(p. 26)
Toggles the VOX function ON and OFF.
•The [VOX GAIN] and [ANTI VOX] are available
on the side panel.
•VOX delay can be set in quick set mode
(p. 48).
SSPPEEEECCHH CCOOMMPPRREESSSSOORR
(p. 26)
Toggles the speech compressor ON and
OFF.
•The [COMP GAIN] control is available on the
side panel.
AAGGCC
(p. 21)
Changes the time constant of the AGC cir-
cuit.
BBRREEAAKK--IINN
(p. 33)
Selects semi break-in, full break-in (QSK)
and break-in OFF
•“BK” or “F-BK” appears when selecting semi
break-in or full break-in, respectively.
•An external switch, such as a foot switch, is
necessary to connect to the ACC socket (pin
3, pin 7 or RTTY SEND—see p. 35) to use no
break-in operation.
11//44 FFUUNNCCTTIIOONN
(p. 36)
Toggles the 1/4 function ON and OFF.
•When the
1
⁄4 function is ON, a bar appears
under the
1
⁄4 indication and fine tuning can be
used.
TTOONNEE SSQQUUEELLCCHH
(p. 31)
Toggles the tone squelch function ON and
OFF (a tone squelch frequency must be
selected in Quick Set mode).
•“FM-TSQL” appears when the function is ON.
RREEPPEEAATTEERR TTOONNEE OOPPEERRAATTIIOONN
(p. 30)
➥ Toggles the subaudible tone encoder
for repeater use ON and OFF.
•“FM-T” appears when the function is ON.
➥ Transmits a 1750 Hz tone burst when
pushed and held during transmission.
•Tone frequencies or tone burst can be set in
initial set mode (p. 49).
D
SS11 FFUUNNCCTTIIOONNSS
MMEEMMOORRYY WWRRIITTEE
(p. 40)
Stores the displayed frequency and oper-
ating mode into the displayed memory
channel.
MMEEMMOO PPAADD WWRRIITTEE
(p. 42)
Stores the displayed frequency and oper-
ating mode into a memo pad.
MMEEMMOO PPAADD RREEAADD
(p. 42)
Calls up a memo pad.
D
SS22 FFUUNNCCTTIIOONNSS
SSCCAANN
(p. 44)
Starts and stops the scan function.
PPRRIIOORRIITTYY WWAATTCCHH
(p. 44)
Starts and stops priority watch.
SSEELLEECCTT SSCCAANN
(p. 44)
Toggles the select setting ON and OFF for
the selected memory channel.
VVFFOO//MMEEMMOORRYY
(p. 44)
Toggles between VFO and memory
modes.
D
SS33 FFUUNNCCTTIIOONNSS
QQUUIICCKK BBAANNDD CCHHAANNGGEE FFUUNNCCTTIIOONN
(p. 19)
This item provides access to the band stacking regis-
ter. By default the 7, 50 and 144 MHz bands are dis-
played. Push [F-1] to [F-3] for 2 sec. to select a new
band if desired.
•A mode is memorized along with the frequency for each
band.
D
SS44 FFUUNNCCTTIIOONNSS
(may be optional for some ver.)
AAUUTTOOMMAATTIICC NNOOTTCCHH FFIILLTTEERR
(p. 24)
This function automatically attenuates beat
tones, tuning signals, etc., even if they are
moving.
NNOOIISSEE RREEDDUUCCTTIIOONN
(p. 24)
This function reduces noise components
and picks out desired signals which are
buried in the noise.
NNOOIISSEE RREEDDUUCCTTIIOONN DDIISSPPLLAAYY
(p. 24)
This displays the noise reduction level
when using the noise reduction function.
F-3
NRL
F-2
NR
F-1
ANF
F-3
V/M
F-2
SEL
F-2
PRI
F-1
SCN
F-3
MPR
F-2
MPW
F-1
MW
F-3
TON
F-2
TSQ
F-1
1/4
F-2
BRK
F-3
AGC
F-2
COM
F-1
VOX
MENU
S1
F-1
MW
F-2
MPW
F-3
MPR
MENU
S2
F-1
SCN
F-2
PRI
SEL
F-3
V/M
(in memory mode)
MENU
S3
F-1
7
F-2
50
F-3
144
MENU
S4
F-1
ANF
F-2
NR
F-3
NRL
IC-706MKIIG.qxd 02.3.27 13:53 Page 4