Operation Manual

6
SET MODE
6-6
PTT Start OFF or ON Turns the PTT Tuner Start function ON or OFF.
[TUNER] Switch Manual or Auto Selects whether or not to store the AT-180’s sta-
tus by each band.
[SPEECH/LOCK] Switch SPEECH/LOCK, LOCK/SPEECH
Selects the function for
SPEECH
when pushed
or held down.
Lock Function MAIN DIAL or PANEL Select the target to be locked when the Lock
function is activated.
Memopad Numbers 5 or 10 Sets the number of usable memopad channels.
MAIN DIAL Auto TS OFF, LOW or HIGH Selects an option for the automatic tuning step
function. When rapidly rotating the main dial, the
tuning step automatically changes according to
the setting.
MIC Up/Down Speed Slow or Fast Selects the microphone’s [∫]/[√] key speed.
[NOTCH] Switch (SSB) Auto, Manual or Auto/Manual Selects the notch function for the SSB mode.
[NOTCH] Switch (AM) Auto, Manual or Auto/Manual Selects the notch function for the AM mode.
SSB/CW Sync Tuning OFF or ON Turns the Synchronous Tuning function ON or
OFF to shift the operating frequency by the offset
amount to keep receiving a signal when the oper-
ating mode is changed between SSB and CW.
CW Normal Side LSB or USB Sets the carrier point for CW normal mode op-
eration to the LSB side or the USB side.
VOICE 1st Menu VOICE-Root or VOICE-TX Select whether or not to directly select the “VOICE
TX” screen, skipping the “VOICE” screen.
KEYER 1st Menu KEYER-Root or KEYER-SEND Select whether or not to directly select the
“KEYER SEND” screen, skipping the “KEYER”
screen.
Speaker Out OFF or ON Selects to mute the speaker output.
MIC AF Out OFF or ON Selects to output the received audio from the
[MIC] connector.
RC MIC
[F-1] ---, P.AMP/ATT, AGC, NB, NR, NOTCH,
RIT, AUTOTUNE/RX>CS, TS, MPAD,
M-CLR, BANK, SPLIT, A/B, DUP,
TONE/DSQL, COMP, TBW, METER,
DR, FROM/TO (DR), SCAN, Voice TX
(T1)
The functions listed to the left can be set to [F-1]
of the optional HM-151
r e m o t e c o n t r o l m i c .
[F-2] ---, P.AMP/ATT, AGC, NB, NR, NOTCH,
RIT, AUTOTUNE/RX>CS, TS, MPAD,
M-CLR, BANK, SPLIT, A/B, DUP,
TONE/DSQL, COMP, TBW, METER,
DR, FROM/TO (DR), SCAN, Voice TX
(T1)
The functions listed to the left can be set to [F-2]
of the optional HM-151
r e m o t e c o n t r o l m i c .
Mode Select
 SSB,  CW,  RTTY,  AM,  FM,
 WFM,  DV
(All boxes are checked.)
Disables the mode selection of the optional HM-
151
r e m o t e c o n t r o l m i c , to simplify operation.
Power OFF (With No Controller) OFF or ON Selects whether or not to automatically turn OFF
the transceiver when the controller is disconnect-
ed from the transceiver.
REF Adjust 0%~100% Sets a number to adjust for a zero beat with a
standard signal such as WWV or WWVH, for fre-
quency calibration.
Set mode items and Default settings (Continued)
NOTE: The default settings shown below in bold are for the USA version.
The default settings may differ, depending on your transceiver version.