Operation Manual
#0 TRANSMIT INDICATOR [TX]
Lights red while transmitting.
#1 RECEIVE INDICA
TOR [RX]
Lights green while receiving a signal and when the
squelch is open.
#2
LCD FUNCTION DISPLAY (p. 13)
Shows the operating frequency, function switch
menus, spectrum scope screen, memory list
screen, set mode settings, etc.
#3 SPLIT OPERA
TION INDICATOR [SPLIT] (p. 88)
Lights during split frequency operation.
#4 MAIN/SUB CHANGE SWITCH [CHANGE]
➥
Switches the frequency and selected memory
channel between main and sub readouts when
pushed.
• Switches between transmit frequency and receive
frequency when the split frequency function is ON.
(p. 88)
➥ Equalizes the sub readout frequency to the
main readout frequency when pushed and held
for 1 sec.
#5
LOCK INDICATOR [LOCK] (p. 82)
Lights when the dial lock function is activated.
#6 DU
ALWATCH SWITCH [DUALWATCH] (p. 79)
➥ Push to turn the dualwatch function ON and
OFF.
• “ ” appears when the dualwatch function
is in use.
➥ Push and hold for 1 sec. to turn the dualwatch
function ON and equalizes the sub readout fre-
quency to the main readout. (Quick dualwatch
function)
• The quick dualwatch function can be turned OFF in
others set mode. (p. 128)
#7 SPLIT SWITCH [SPLIT] (p. 88)
➥ Push to turn the split function ON and OFF.
• “ ” appears when the split function is in
use.
➥ Push and hold for 1 sec. to activate the quick
split function.
• The split function ON and equalize the sub readout
frequency to the main readout and sets the sub
readout for frequency input in non-FM modes. (p. 89)
• The offset frequency is shifted from the selected
VFO frequency in FM mode. (p. 129)
• The tone encoder function is turned ON in FM
mode.
• The quick split function can be turned OFF in others
set mode. (p. 129)
#8 KEYPAD
➥ Pushing a key selects the operating band. (p. 27)
• [GEN •] selects the general coverage band.
➥ Pushing the same key 2 or 3 times calls up
other stacked frequencies in the band.
(p. 27)
• Icom’s triple band stacking register memorizes 3 fre-
quencies in each band.
➥ After pushing [F-INP ENT], push a key on the
keypad to enter a numeric frequency. After en-
tering, push [F-INP ENT] to select the desired
frequency directly
(p. 28)
• e.g. to enter 14.195 MHz;
Push [F-INP ENT] [1] [4] [•] [1] [9] [5] [F-INP ENT].
➥ After pushing [F-INP ENT], push a key on the
keypad to enter a memory channel. After enter-
ing, push [∫]/[√] to select the desired memory
channel directly.
(p. 99)
■ Front panel (continued)
TWIN
-
PBT
RIT/ TX
Ӡ
NOTCH
CW PITCH
VOICE MEMORY
BAL NR
AF RF/SQL
MIC GAIN RF POWER BK
-
IN DELAY KEY SPEED
TIMER
PHONES
ELEC
-
KEY
MIC
AUTO
TUNE
GENE F
-
INP
1.8 3.5
1 2
14
5
18
6
7
3
24
8
28
9
50
0
ENT
4
7
10
21
CHANGE
TS
XFC
SPLIT
DUAL
WATCH
MAIN
/
SUB
M.SCOPE
VFO/MEMO
MP
-
W
MW
MP
-
R
F
-
6
F
-
5
F
-
4
F
-
3
F
-
2
F
-
1
NRNB
PBT
-
CLR
APF/TPF
NOTCH
POWER
RIT
CLEAR
TX
Ӡ
SPEECH
LOCK
FILTER
REC PLAY
EXIT
/
SET
SSB CW
RTTY
/
PSK
AM/FM
MONITOR
TRANSMIT
TUNER
HF/50MHz TRANSCEIVER
LOCKTX RX SPLIT
$2
$3
#0 #5#4 #6 #7 #8 #9
$0
#3#2#1
$1
$4$5
7
1
PANEL DESCRIPTION