Operation Manual

8
SET MODE
8-6
Connectors (Continued)
DATA1 MOD (Default: ACC)
DATA2 MOD (Default: USB)
DATA3 MOD (Default: MIC, USB)
Selects the connector(s) to input the modulation signal
when the data mode is ON.
L Touching the [DATA] key in the MODE screen
activates the data mode and does the following:
• In transmit, it locks the transmission pass bandwidth to
the default MID (300 – 2700 Hz).
• In receive, it changes the lter selection from the SSB
lter set to the CW lter set. (However, you can still
adjust the set receive IF lter bandwidths by touching
the lter icon for 1 second.) This enables the 1/4 Tuning
function setting in the FUNCTION screen. (Disables the
Speech Compressor)
• It automatically sets the modulation input to the “MIC,”
“ACC,” “MIC, ACC,” “USB,” “MIC, USB” or “LAN”
connector(s) selected in this item, for all three data
modes.
MENU
» SET > Connectors > USB SEND/Keying
USB SEND (Default: OFF)
You can control transmit and receive from the PC
through the USB port.
Selects the control port to be used for communication
between the IC-7610 and PC.
L You cannot select the terminal which is already
selected in the “USB Keying (CW)” or “USB Keying
(RTTY)” item.
USB Keying (CW) (Default: OFF)
You can control transmit, receive and keying from the
PC, through the USB port.
Selects the control port to be used for communication
between the IC-7610 and PC.
L You cannot select the terminal which is already
selected in the “USB SEND” or “USB Keying
(RTTY)” item.
USB Keying (RTTY) (Default: OFF)
You can control transmit, receive and RTTY (FSK)
from the PC, through the USB port.
Selects the control port to be used for communication
between the IC-7610 and PC.
L You cannot select the terminal which is already
selected in the “USB SEND” or “USB Keying (CW)”
item.
MENU
» SET > Connectors > External Keypad
VOICE (Default: OFF)
Enables voice memory transmission using an external
keypad.
KEYER (Default: OFF)
Enables keyer memory transmission using an external
keypad.
RTTY (Default: OFF)
Enables RTTY memory transmission using an
external keypad.
PSK (Default: OFF)
Enables PSK memory transmission using an external
keypad.
MENU
» SET > Connectors > Keyboard/Mouse
Keyboard [F1]-[F8] (VOICE) (Default: OFF)
Enables the Voice TX memory transmission using a
keyboard connected to [USB].
Keyboard [F1]-[F8] (KEYER) (Default: OFF)
Enables keyer memory transmission using a keyboard
connected to [USB].
Keyboard Type (Default: English)
Selects the keyboard language.
Keyboard Repeat Delay (Default: 250ms)
Sets the repeat delay time of the keyboard.
Keyboard Repeat Rate (Default: 10.9cps)
Sets the repeat rate of the keyboard.
Mouse Pointer Speed (Default: MID)
Selects the mouse pointer speed.
Mouse Pointer Acceleration (Default: ON)
Turns the mouse pointer acceleration ON or OFF.
MENU
» SET > Connectors > USB DIAL
USB DIAL Select (Default: SUB Only)
Selects the Sub band or Main and Sub band to
operate on the RC-28’s main dial.
USB DIAL Auto TS (Default: High)
Selects the Automatic Tuning Step for the RC-28’s
main dial.
When rapidly rotating the RC-28’s main dial, the
tuning step is automatically changed according to the
rotation speed.
USB DIAL [TRANSMIT] Switch
(Default: Push to toggle)
Selects whether to toggle between transmit and
receive by pushing, or to transmit only while holding
the [TRANSMIT] key on the RC-28.