IC-F310(new) 02.3.23 1:34 PM ページ18 INSTRUCTION MANUAL VHF TRANSCEIVER iF310 iF320 UHF TRANSCEIVER iF410 iF420 This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.
IC-F310(new) 02.3.23 1:33 PM ページi IMPORTANT CAUTIONS READ ALL INSTRUCTIONS carefully and com- RWARNING! NEVER connect the transceiver to an pletely before using the transceiver. AC outlet. This may pose a fire hazard or result in an electric shock. SAVE THIS INSTRUCTION MANUAL — This instruction manual contains important operating instructions for the IC-F310, IC-F320, IC-F410 and IC-F420 VHF/UHF TRANSCEIVERS.
IC-F310(new) 02.3.23 1:33 PM ページii TABLE OF CONTENTS DO NOT use or place the transceiver in areas with temperatures below –30°C or above +60°C or, in areas subject to direct sunlight, such as the dashboard. IMPORTANT ........................................................................ i EXPLICIT DEFINITIONS ..................................................... i CAUTIONS .......................................................................... i TABLE OF CONTENTS .....................................
IC-F310(new) 02.3.23 1:33 PM ページ1 1 PANEL DESCRIPTION ■ Front panel VOLUME UP/DOWN KEYS (P. 2) MICROPHONE CONNECTOR (P. 2) 1 FUNCTION DISPLAY (P. 2) CH UP/DOWN KEYS [ PROGRAMMABLE FUNCTION KEYS [P0],[P1],[P2],[P3] (P. 3) ]/[ ] (P. 3) POWER SWITCH (P.
IC-F310(new) 02.3.23 1:33 PM ページ2 PANEL DESCRIPTION VOLUME UP/ DOWN KEYS Push to adjust the audio output level. • Minimum audio level is pre-programmed. CH UP/DOWN [ ]/[ ] KEYS • Push to select the operating channel. • Can be programmed for one of several functions by yourdealer. POWER SWITCH Turns the power ON and OFF.
IC-F310(new) 02.3.23 1:33 PM ページ3 1 PANEL DESCRIPTION ■ Programmable function keys PRI A PRI B The following functions can be assigned to [P0], [P1], [P2], [P3], [ ] and [ ] programmable function keys. Consult your Icom Dealer or System operator for details concerning your transceivers programming. In the following explanations, programmable function names are bracketed, the specifc switch used to activate the function depends on programming.
IC-F310(new) 02.3.23 1:33 PM ページ4 PANEL DESCRIPTION LOCK MONI W/N LOCK KEY Electronically locks all programmable keys except the following: • [CALL] (incl. CAL A and CAL B), [MONI] and [EMER] keys. MONITOR KEY Activates one of (or two of) the following functions on each channel independently: HIGH LOW1 OUTPUT POWER SELECTION KEYS Select the transmit output power temporarily or permanently depending on the pre-setting.
IC-F310(new) 02.3.23 1:33 PM ページ5 1 PANEL DESCRIPTION TX CH TX CODE KEY Select a transmit 5-tone code (station code) channel. • Push and hold to changes the contents of the station code using [ ]/[ ] keys. • Push to selects a TX 5-tone code channel using [ ]/[ ] keys after pushing this key. CODE TX CODE CHANNEL UP/DOWN KEY Push to selects a TX code channel directory. DTMF DTMF CHANNEL SELECT KEY Push this key to select a DTMF channel.
IC-F310(new) 02.3.23 1:33 PM ページ6 OPERATION 2 ■ Turning power ON ■ Channel selection I ] to turn the power ON. q Push [K Several types are available, and the channel selection method may differ according to your system set up. • A power-up alert tone sounds for about 1 sec. and an opening message may appear. Opening message may differ depending on the pre-setting. w If the transceiver is programmed for a start up passcode, input digit codes as directed by your System operator.
IC-F310(new) 02.3.23 1:33 PM ページ7 2 OPERATION ■ Receiving and transmitting RECEIVING: I ] to turn the power ON. q Push [K w Push [ ]/[ ] to select a channel. e When receiving a call, adjust the volume [UP] or [DOWN] to a comfortable listening level. IMPORTANT: To maximize the readability of your signal: (1) pause briefly after pushing [PTT], (2) hold the transceiver 15 to 20 cm from your mouth, then speak into the microphone at a normal voice level.
IC-F310(new) 02.3.23 1:33 PM ページ8 OPERATION 2 D Tx code channel selection D DTMF transmission If the transceiver has a [TX CH] key, display can be toggled between the operating channel number (or name) and Tx code channel number (or name). When the Tx code channel number (or name) is displayed, the [ ]/[ ] keys select the Tx code channel. If the transceiver has a [DTMF] key, the automatic DTMF transmission function is available. Up to 7 DTMF channels may be available.
IC-F310(new) 02.3.
IC-F310(new) 02.3.23 1:33 PM ページ10 CONNECTION AND MAINTENANCE ⁄ ANTENNA CONNECTOR Connects to an antenna. Ask your Dealer about antenna selection and placement. (See p. 12) ■ Supplied Accessories 1 2 4 3 ¤ MICROPHONE HANGER Connect the supplied microphone hanger to the vehicle’s ground for on/off hook microphone functions. (See p. 2) ‹ DC POWER RECEPTACLE Connects to a 12 V DC battery. Pay attention to polarities. NEVER connect to a 24 V battery. This could damage the transceiver.
IC-F310(new) 02.3.23 1:34 PM ページ11 3 CONNECTION AND MAINTENANCE ■ Mounting the transceiver The universal mounting bracket supplied with your transceiver allows overhead mounting. Please read the following instructions carefully. • Mount the transceiver securely with the 4 supplied screws to a thick surface which can support more then 1.5 kg. ■ Optional UT-96/UT-105 installation The optional UT-96/UT-105 units install as follows: q w e r Turn power OFF, then disconnect the DC power cable.
IC-F310(new) 02.3.23 1:34 PM ページ12 CONNECTION AND MAINTENANCE 3 ■ Optional OPC-617 installation ■ Antenna Install the OPC-617 as shown below. A key element in the performance of any communication system is an antenna. Ask your Dealer about antennas and the best places to mount them. ■ Fuse replacement Two fuses are installed in the supplied DC power cable.
IC-F310(new) 02.3.23 1:34 PM ページ13 4 OPTIONAL SmarTrunk II™ OPERATION ■ SmarTrunk II™ and conventional modes This transceiver is capable of SmarTrunk II™ functions. The optional UT-105 allows communication in conventional channels or SmarTrunk II™ channels. Select a channel bank for SmarTrunk II™ before trunking operation. • Push [BANK] one or more times to select a channel bank for conventional channels or SmarTrunk II™ channels. • Scanning starts when a channel bank for SmarTrunk II™ is selected.
IC-F310(new) 02.3.23 1:34 PM ページ14 OPTIONAL SmarTrunk II™ OPERATION 4 D Terminating a call D Programming memory speed dial After completing a call, push [#] to disconnect (hang up). q Push and hold [M] until you hear a high-pitched beep. w Enter the memory location (0–9, A, B, C, D), the telephone or subscriber number, then [1], [M] (or [3], [M] if for another system subscriber). IMPORTANT: If one person in the conversation terminates a call, all participants will be cut off.
IC-F310(new) 02.3.23 1:34 PM ページ15 4 OPTIONAL SmarTrunk II™ OPERATION D Clear channel alerting If all channels are busy, the transceiver automatically begins searching for an open channel and beeps every ten seconds. When two short beeps (low-pitched, then high-pitched) are heard, a channel is available. Push [M], [M] immediately to redial the last number. NOTE: For additional operating instructions, contact your Dealer or System Operator.
IC-F310(new) 02.3.23 1:34 PM ページ16 OPTIONS 5 EXTERNAL SPEAKERS SP-5 Large speaker for good audio quality. Input impedance: 4 Ω Max. input power: 5 W SP-10 Compact and easy-to-install. Input impedance: 4 Ω Max. input power: 5 W HM-100T/TA DTMF microphone. UT-96 5-TONE UNIT Provides 2-tone/5-tone signaling . UT-105 SmarTrunk II™ Logic Board Provides SmarTrunk II™ capabilities. OPC-617 ACC CABLE Allows you to connect to an external terminal. HM-100 Normal microphone.
IC-F310(new) 02.3.23 1:34 PM ページ17 A-5458D-1EX-e Printed in Japan © 1997 by Icom Inc.
DECLARATION OF CONFORMITY We Icom Inc. Japan 1-1-32, Kamiminami, Hirano-ku Osaka 547-0003, Japan Declare on our sole responsibility that this equipment complies the essential requirements of the Radio and Telecommunications Terminal Equipment Directive, 1999/5/EC, and that any applicable Essential Test Suite measurements have been performed. Kind of equipment: VHF TRANSCEIVER Type-designation: iC- f310/s 146–174 MHz 12.5 KHz/ 20 KHz/ 25 KHz Version (where applicable): 0168 Düsseldorf 07 Feb.
INSTALLATION NOTES ABOUT CE CE Versions of the IC-F310/S which display the “CE” symbol on the serial number seal, comply with the essential requirements of the European Radio and Telecommunication Terminal Directive 1999/5/EC. This warning symbol indicates that this equipment operates in non-harmonised frequency bands and/or may be subject to licensing conditions in the country of use.
DECLARATION OF CONFORMITY We Icom Inc. Japan 1-1-32, Kamiminami, Hirano-ku Osaka 547-0003, Japan Declare on our sole responsibility that this equipment complies the essential requirements of the Radio and Telecommunications Terminal Equipment Directive, 1999/5/EC, and that any applicable Essential Test Suite measurements have been performed. Kind of equipment: UHF TRANSCEIVER Type-designation: iC- f410/s 440-470 MHz 12.5 KHz/ 25 KHz 400-430 MHz 12.
INSTALLATION NOTES ABOUT CE CE Versions of the IC-F410/S which display the “CE” symbol on the serial number seal, comply with the essential requirements of the European Radio and Telecommunication Terminal Directive 1999/5/EC. This warning symbol indicates that this equipment operates in non-harmonised frequency bands and/or may be subject to licensing conditions in the country of use.