IC-F510_F610_EU-6.qxd 05.12.
IC-F510_F610_EU-6.qxd 05.12.14 2:59 PM Page b (1,1) IMPORTANT CAUTIONS READ ALL INSTRUCTIONS carefully and com- RWARNING! NEVER connect the transceiver to an AC outlet. This may pose a fire hazard or result in an electric shock. pletely before using the transceiver. SAVE THIS INSTRUCTION MANUAL — This instruction manual contains important operating instructions for the IC-F510 VHF TRANSCEIVER AND IC-F610 UHF TRANSCEIVER.
IC-F510_F610_EU-6.qxd 05.12.14 2:59 PM Page c (1,1) TABLE OF CONTENTS peratures below –25°C or above +55°C or, in areas subject to direct sunlight, such as the dashboard. AVOID operating the transceiver without running the vehicle’s engine. The vehicle’s battery will quickly run out if the transceiver is in transmission while the vehicle’s engine OFF. AVOID placing the transceiver in excessively dusty environments. AVOID placing the transceiver against walls. This will obstruct heat dissipation.
IC-F510_F610_EU-6.qxd 05.12.14 2:59 PM 1 Page d (1,1) PANEL DESCRIPTION ■ Front panel q w u y q AF VOLUME CONTROL KNOB ➥Rotate the knob to adjust the audio output level. • Minimum audio level is pre-programmed. ∫]/[√ √] KEYS w LEFT UP/DOWN [∫ ➥One of several functions can be programmed by your Dealer. (Same as [P0] to [P4] keys) 1 e r t e FUNCTION DISPLAY ➥Displays variety of information, such as an operating channel number/name, 5-tone code, DTMF numbers and audible condition, etc.
IC-F510_F610_EU-6.qxd 05.12.14 2:59 PM Page e (1,1) PANEL DESCRIPTION t DEALER-PROGRAMMABLE KEYS [P0] to [P4] ➥Desired functions can be programmed independently by your Dealer. ■ Function display q w e r t y u i y POWER SWITCH [POWER] ➥Push to turns the power ON and OFF.
IC-F510_F610_EU-6.qxd 05.12.14 2:59 PM 1 Page f (1,1) PANEL DESCRIPTION u SCRAMBLER INDICATOR ➥Appears when scrambler function is activated. (Optional UT109 (#02)/UT110 (#02) SCRAMBLER UNIT is required.) i 2/5TONE INDICATOR ➥Appears when specified 2/5tone call is received. o ALPHANUMERIC DISPLAY ➥Displays the CH number, 5-tone indication, DTMF numbers, Audible indication, etc.
IC-F510_F610_EU-6.qxd 05.12.14 2:59 PM Page g (1,1) PANEL DESCRIPTION [BANK] BANK KEY Select and determine a bank number. [MONI] • When the optional UT-105 is installed, push [BANK] then push [CH UP]/[CH DN] to select operating bank number, and then push [BANK] to determine the bank number. NOTE: Place the microphone on hook to start scanning. Take the microphone off hook to stop scanning.
IC-F510_F610_EU-6.qxd 05.12.14 2:59 PM 1 PANEL DESCRIPTION [TA] [CALL] [CAL A] [CAL B] [EMER] 5 Page h (1,1) TALK AROUND KEY Turns the talk around function ON and OFF. • The talk around function equalises the transmit frequency to the receive frequency for mobileto-mobile communication. CALL KEYS Transmit a 5-tone code. • Call transmission is necessary before you call another station depending on your signaling system.
IC-F510_F610_EU-6.qxd 05.12.14 2:59 PM Page i (1,1) PANEL DESCRIPTION [ID MR] [GRP] [COMP] [SET] ID MEMORY READ KEY Recalls detected ID codes. • Push this key, then push [ ]/[ ] for selection. • Up to 5 ID’s are memorized. Push and hold this key to erase all memorized IDs. TRUNKING GROUP KEY Push to select the Trunking group. MIC COMPANDER KEY Push to toggle the mic compander function ON or OFF. USER SET MODE KEY Changes the contents of the items in the User Set mode. • Push and hold [SET] for 1 sec.
IC-F510_F610_EU-6.qxd 05.12.14 2:59 PM 2 Page j (1,1) OPERATION ■ Turning power ON ■ Channel selection q Push [POWER] to turn the power ON. Several types channel selections are available, methods may differ according to your system set up. • A power-up alert tone sounds for about 1 sec. and an opening message may appear. w If the transceiver is programmed for a start up passcode, input digit codes as directed by your Dealer.
IC-F510_F610_EU-6.qxd 05.12.14 2:59 PM Page k (1,1) OPERATION ■ Receiving and transmitting RECEIVING: q Push [POWER] to turn the power ON. w Push [CH UP] or [CH DN] to select a channel. e When receiving a call, adjust the audio output level to a comfortable listening level. TRANSMITTING: r Take the microphone off hook. • 5-tone mute may be released (the ‘audible’ condition is selected and “ ” appears). • A priority channel may be selected automatically. t Wait for the channel to become clear.
IC-F510_F610_EU-6.qxd 05.12.14 2:59 PM 2 Page l (1,1) OPERATION D Tx code channel selection D DTMF transmission If the transceiver has a [TX CH] key, display can be toggled between the operating channel number (or name) and Tx code channel number (or name). When the Tx code channel number (or name) is displayed, the [CH UP]/[CH DN] keys select the Tx code channel. If the transceiver has a [DTMF] key, the automatic DTMF transmission function is available. Up to 7 DTMF channels are available.
IC-F510_F610_EU-6.qxd 05.12.14 2:59 PM Page m (1,1) OPERATION 2 D User set mode User set mode is accessed at power ON and allows you to set seldom-changed settings. In this case you can “customize” transceiver operation to suit your preferences and operating style. Entering the user set mode: qWhile pushing and holding [ ] and [ ], push [POWER] to enter user set mode ON, allowing you to set seldomchanged settings. wPush and hold [P0] to enter user set mode. Push [P0] momentarily to select the item.
IC-F510_F610_EU-6.qxd 05.12.14 2:59 PM 3 Page n (1,1) OPTIONAL SmarTrunk II™ OPERATION ■ SmarTrunk II™ and conventional modes This transceiver is capable of SmarTrunk II™ functions. The optional UT-105 allows communication in conventional channels or SmarTrunk II™ channels. Select a channel bank for SmarTrunk II™ before trunking operation. • Push [BANK] several times to select a channel bank for conventional channels or SmarTrunk II™ channels.
IC-F510_F610_EU-6.qxd 05.12.14 2:59 PM Page o (1,1) OPTIONAL SmarTrunk II™ OPERATION 3 D Terminating a call D System busy indication After completing a call, push [#] to disconnect (hang up). If all channels are busy, three low beeps sound after you initiate a call. Try the call again later. IMPORTANT: If one person in the conversation terminates a call, all participants will be cut off. D Last number re-dial Push [M] 2times to automatically re-dial the last called number.
IC-F510_F610_EU-6.qxd 05.12.14 2:59 PM 4 Page p (1,1) CONNECTION AND MAINTENANCE ■ Rear panel and connection Optional speaker (SP-22) w q Antenna r Red: + NEVER connect to a 24 V battery. t Optional cable (OPC-617) e Supplied DC power cable Black: Note: Use the terminals for the cable connections.
IC-F510_F610_EU-6.qxd 05.12.15 4:40 PM Page q (1,1) CONNECTION AND MAINTENANCE ⁄ ANTENNA CONNECTOR Connects to an antenna. Ask your Dealer about antenna selection and placement. ■ Supplied Accessories q w r e ¤ MICROPHONE HANGER Connect the supplied microphone hanger to the vehicle’s ground for microphone on/off hook functions. (See p. 2) ‹ DC POWER RECEPTACLE Connects to a 12 V DC battery. Pay attention to polarities. NEVER connect to a 24 V battery. This could damage the transceiver.
IC-F510_F610_EU-6.qxd 05.12.14 2:59 PM 4 Page r (1,1) CONNECTION AND MAINTENANCE ■ Mounting the transceiver The front panel can be inverted for correct viewing while leaving the built-in speaker facing away from the mounting surface. D Inverting the Front panel r Invert the transceiver 180 degrees clockwise as below. t Re-attach the Front panel to the transceiver. y Tighten the 2 screws. q Unscrew the 2-side screws. w Detach the Front panel forward from the transceiver.
IC-F510_F610_EU-6.qxd 05.12.14 2:59 PM Page s (1,1) CONNECTION AND MAINTENANCE 4 D Mounting the transceiver The universal mounting bracket supplied with your transceiver allows overhead mounting. • Mount the transceiver securely with the 4 supplied screws to a thick surface which can support more than 1.5 kg.
IC-F510_F610_EU-6.qxd 05.12.14 2:59 PM 4 Page t (1,1) CONNECTION AND MAINTENANCE ■ Optional UT-105 and UT-108 installation ■ Optional UT-109 /UT-110 installation The optional UT-105 and UT-108 units install as follows: q Turn power OFF, then disconnect the DC power cable. w Unscrew the 4 screws, then remove the bottom cover. e Cut the print pattern on the PCB at the TX mic circuit (A) and RX AF circuit (B) as shown in the following figure. r Install the scrambler unit as shown in the left.
IC-F510_F610_EU-6.qxd 05.12.14 2:59 PM Page u (1,1) CONNECTION AND MAINTENANCE 4 ■ Optional OPC-617 installation ■ Antenna Install the OPC-617 as shown below. A key element in the performance of any communication system is an antenna. Ask your Dealer about antennas and the best places to mount them. ■ Fuse replacement Two fuses are installed in the supplied DC power cable.
IC-F510_F610_EU-6.qxd 05.12.14 2:59 PM 5 Page v (1,1) OPTIONS SP-22 EXTERNAL SPEAKER Compact and easy-to-install. Input impedance: 4 Ω Max. input power: 5 W HM-152/HM-152T/HM-148 HAND MICROPHONE • HM-152 : Hand microphone. The same as that supplied with the transceiver. • HM-152T : DTMF microphone • HM-148 : Heavy duty microphone SM-25 Desktop microphone. UT-105 SmarTrunk II™ Logic Board Provides SmarTrunk II™ capabilities. UT-108 DTMF DECODER UNIT Provides pager and code squelch capabilities.
IC-F510_F610_EU-6.qxd 05.12.14 2:59 PM Page w (1,1) DOC DECLARATION OF CONFORMITY We Icom Inc. Japan 1-1-32, Kamiminami, Hirano-ku Osaka 547-0003, Japan Declare on our sole responsibility that this equipment complies with the essential requirements of the Radio and Telecommunications Terminal Equipment Directive, 1999/5/EC, and that any applicable Essential Test Suite measurements have been performed. Kind of equipment: UHF TRANSCEIVER Type-designation: iC-f610 440—490 MHz 12.
IC-F510_F610_EU-6.qxd 05.12.14 3:26 PM Page Z (1,1) < Intended Country of Use > GER AUT GBR IRL A-6121H-1EU-y Printed in Japan © 2001–2006 Icom Inc.
