IC-F70_F80-1.qxd 05.1.18 4:26 PM Page a (1,1) INSTRUCTION MANUAL VHF TRANSCEIVER iF70DT/DS iF70T/S UHF TRANSCEIVER iF80DT/DS iF80T/S This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. The photo shows the IC-F70DT/T or IC-F80DT/T.
IC-F70_F80-1.qxd 05.1.18 4:26 PM Page i (1,1) IMPORTANT ABOUT APCO PROJECT 25 READ ALL INSTRUCTIONS carefully and com- This device made under license under one or more of the following US patents: #4,590,473, #4,636,791, #5,148,482, #5,185,796, #5,271,017, #5,377,229. pletely before using the transceiver. SAVE THIS INSTRUCTION MANUAL — This instruction manual contains important operating instructions for the IC-F70DT/F70DS/F70T/F70S VHF TRANSCEIVERS and IC-F80DT/F80DS/F80T/F80S UHF TRANSCEIVERS.
IC-F70_F80-1.qxd 05.1.18 4:26 PM Page ii (1,1) PRECAUTIONS R CAUTION! NEVER hold the transceiver so that the DO NOT modify the transceiver for any reason. antenna is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 5 to 10 cm (2 to 4 in.) away from the lips and the transceiver is vertical. Optional unit installation should be done at authorized Icom service center only.
IC-F70_F80-1.qxd 05.1.18 4:26 PM Page iii (1,1) TABLE OF CONTENTS IMPORTANT .................................................................................... i EXPLICIT DEFINITIONS ................................................................. i ABOUT APCO PROJECT 25 ........................................................... i PRECAUTIONS .............................................................................. ii TABLE OF CONTENTS .............................................................
IC-F70_F80-1.qxd 05.1.18 4:26 PM Page 1 (1,1) ACCESSORIES ■ Supplied accessories ■ Accessory attachments The following accessories are supplied: Qty. q Flexible antenna ……………………………………………1 w Battery pack …………………………………………………1 e Belt clip ………………………………………………………1 r Connector cover (with screw) …………………………1 set D Flexible antenna q w e 1 1 Connect the supplied flexible antenna to the antenna connector. CAUTION! • NEVER HOLD by the antenna when carrying the transceiver.
IC-F70_F80-1.qxd 05.1.18 4:26 PM 1 Page 2 (1,1) ACCESSORIES ï Battery pack D Belt clip To attach the battery pack: Slide the battery pack in the direction of the arrow (q), then lock it with the battery release button. To attach the belt clip: q Release the battery pack if it is attached. w Slide the belt clip in the direction of the arrow until the belt clip is locked and makes a ‘click’ sound. • Slide the battery pack until the battery release button makes a ‘click’ sound.
IC-F70_F80-1.qxd 05.1.18 4:26 PM Page 3 (1,1) ACCESSORIES 1 ï Connector cover 1 Attach the connector cover when the optional speaker-microphone is not used. To attach the connector cover: q Insert the connector cover into the multi-connector. w Tighten the screw. To detach the connector cover: e Unscrew the screw using a phillips screwdriver. r Detach the connector cover for the speakermicrophone connection.
IC-F70_F80-1.qxd 05.1.18 4:26 PM 2 Page 4 (1,1) PANEL DESCRIPTION ■ Front panel w q !2 !1 !0 e r t Speaker y Microphone u r EMERGENCY SWITCH Push and hold for a specified period to transmit an emergency call. • Desired function can be programmed by your dealer. (p. 7) t BUSY/TRANSMIT INDICATOR ➥ Lights green while receiving a signal, or when the squelch is open. ➥ Lights red while transmitting. y MULTI-CONNECTOR Connect the optional speaker-microphone.
IC-F70_F80-1.qxd 05.1.18 4:26 PM Page 5 (1,1) PANEL DESCRIPTION o 10-KEYPAD (IC-F70DT/F70T or IC-F80DT/F80T only) The keypad allows you to enter digits to: • Select memory channels, tone channels and DTMF codes (during transmission). • Set TX codes and BIIS status number. • Input text message for SDM operation. • Start up with a password. • Input the Individual ID code for digital operation. !0 MONITOR SWITCH ➥ Mute and release the CTCSS (DTCS) or 2-tone squelch mute.
IC-F70_F80-1.qxd 05.1.18 4:26 PM 2 Page 6 (1,1) PANEL DESCRIPTION ■ Function display t SCRAMBLER INDICATOR Appears when the voice scrambler function is activated. q we r tyui o y BELL INDICATOR Appears/blinks when the specific 2/5-tone/BIIS code is received, according to the pre-programming. !0 !1 q SIGNAL STRENGTH INDICATOR Indicates relative signal strength level. w LOW POWER INDICATOR Appears when low output power is selected.
IC-F70_F80-1.qxd 05.1.18 4:26 PM Page 7 (1,1) PANEL DESCRIPTION 2 ■ Programmable function keys The following functions can be assigned to [EMERGENCY], [UP], [DOWN], [MONITOR], [P0], [P1], [P2] and [P3] programmable function keys. Consult your Icom dealer or system operator for details concerning your transceivers programming. If the programmable function names are bracketed in the following explanations, the specific key is used to activate the function depends on the programming.
IC-F70_F80-1.qxd 05.1.18 4:26 PM 2 Page 8 (1,1) PANEL DESCRIPTION SCAN ADD/DEL (TAG) KEY “SCAD” Push to add or delete the selected channel to/from the scan group. LIGHT KEY “LIGT” Push to turn the transceiver’s backlight ON temporarily only when the backlight function is turned OFF in user set mode. PRIO A/B KEYS “PRA”/“PRAR”/“PRB”/“PRBR” ➥ Push to select Priority A or Priority B channel.
IC-F70_F80-1.qxd 05.1.18 4:26 PM Page 9 (1,1) PANEL DESCRIPTION 2 DTMF AUTODIAL KEY “DTMA” ➥ Push to enter the DTMF channel selection mode. Then select the desired DTMF channel using [CH Up]/[CH Down]. ➥ After selecting the desired DTMF channel, push this key to transmit the DTMF code. SURVEILLANCE KEY “SURV” Push to turn the surveillance function ON or OFF. When this function is turned ON, the beep is not emitted and the LCD backlight does not light when a signal is received or a key is pushed, etc.
IC-F70_F80-1.qxd 05.1.18 4:26 PM 2 Page 10 (1,1) PANEL DESCRIPTION ID-MR SELECT KEY “IDMS” (PMR or BIIS PMR operation only) ➥ Recalls detected ID codes. • Push this key, then select the ID code using [CH Up]/[CH Down]. • Up to 5 ID’s are memorized. ➥ Push and hold to erase the selected ID’s. SCRAMBLER FUNCTION “SCR” Push to toggle the voice scrambler function ON and OFF. COMPANDER KEY “COMP” Push to toggle the compander function ON and OFF.
IC-F70_F80-1.qxd 05.1.18 4:26 PM Page 11 (1,1) PANEL DESCRIPTION TONE/NAC CH SELECT KEY “TSEL” (LMR (P25 Conventional) operation only) ➥ While in the analog mode operation, push to select the continuous tone channel using [CH Up] or [CH Down] to change the tone frequency/code setting. ➥ While in the digital mode operation, push to select the NAC channel using [CH Up] or [CH Down] to change the NAC code setting.
IC-F70_F80-1.qxd 05.1.18 4:26 PM 3 Page 12 (1,1) BASIC OPERATION ■ Turning power ON ■ Channel selection Prior to using the transceiver for the first time, the battery pack must be fully charged for optimum life and operation. (P. 30) q Rotate [VOL] to turn the power ON. w If the transceiver is programmed for a start up password, input the digit codes as directed by your dealer. • 10-keypad* can be used for password input.
IC-F70_F80-1.qxd 05.1.18 4:26 PM Page 13 (1,1) BASIC OPERATION 3 ■ Call procedure ■ Receiving and transmitting When your system employs tone signaling (excluding CTCSS and DTCS), the call procedure may be necessary prior to voice transmission. The tone signalling employed may be a selective calling system which allows you to call specific station(s) only and prevent unwanted stations from contacting you. Receiving: q Rotate [VOL] to turn the power ON.
IC-F70_F80-1.qxd 05.1.18 4:26 PM 3 Page 14 (1,1) BASIC OPERATION D Transmitting notes D TX code channel selection • Transmit inhibit function The transceiver has several inhibit functions which restrict transmission under the following conditions: - The channel is in mute condition (‘Inaudible’ condition; “ ” does not appear.) - The channel is busy. - Un-matched (or matched) CTCSS is received.
IC-F70_F80-1.qxd 05.1.18 4:26 PM Page 15 (1,1) BASIC OPERATION 3 D TX code number edit (PMR or BIIS PMR operation only) If the transceiver has [TX Code CH Select] or [TX Code Enter] assigned to it, TX code contents can be edited within the allowable digits. USING [TX CODE CH SELECT] KEY: q Push [TX Code CH Select] to enter the TX code channel selection mode. • Select the desired channel before entering the TX code channel selection mode if necessary. w Push and hold [TX Code CH Select] for 1 sec.
IC-F70_F80-1.qxd 05.1.18 4:26 PM 3 Page 16 (1,1) BASIC OPERATION D Individual ID code selection D Talkgroup ID code selection (Digital mode operation only) If the transceiver has [Individual] assigned to it, the indication can be toggled between the operating channel number (or name) and Individual ID code (or name). When the Individual ID code (or name) is displayed, [CH Up] or [CH Down] selects the desired Individual ID code.
IC-F70_F80-1.qxd 05.1.18 4:26 PM Page 17 (1,1) BASIC OPERATION 3 ■ User set mode User set mode is accessed at power ON and allows you to set seldom-changed settings. In this case you can “customize” the transceiver operation to suit your preferences and operating style. Entering the user set mode: q While pushing and holding [P1] and [P2], rotate [VOL] to turn the power ON. Then, push and hold [P0] to enter user set mode. [VOL] e Rotate [VOL] to turn the power OFF to exit set mode.
IC-F70_F80-1.qxd 05.1.18 4:26 PM 3 Page 18 (1,1) BASIC OPERATION ■ Scrambler function The voice scrambler function provides private communication between stations. The frequency inversion type is equipped to all versions, moreover, the optional Rolling or Non-rolling type can be available. q Push [Scrambler] to turn the scrambler function ON. •“ ” appears. w Push [Scrambler] again to turn the scrambler function OFF. •“ 18 ” disappears.
IC-F70_F80-1.qxd 05.1.18 4:26 PM Page 19 (1,1) BIIS OPERATION ■ Default setting The following functions are assigned to each programmable key as the default. However, the assigned function can be changed by your dealer. Ask your dealer for details. During digital mode operation, BIIS is not available. NOTE: [TX Code Enter] must be assigned to a key. [P0]; Call : Push to transmit a 5-tone/BIIS call when the selected channel is a 5-tone or BIIS channel.
IC-F70_F80-1.qxd 05.1.18 4:26 PM 4 Page 20 (1,1) BIIS OPERATION D Group call D Displaying the received call record — Queue indication q When a group call is received; • Beeps sound. • “ ” appears and the mute is released. • The programmed text message (e.g.“GROUP”) and the calling station ID (or text) is displayed when the indication mode is 2 lines. • The programmed text message (e.g.
IC-F70_F80-1.qxd 05.1.18 4:26 PM Page 21 (1,1) BIIS OPERATION 4 ■ Transmitting a call A total of 3 ways for code selection are available—selecting the call code from memory, entering the call code from the keypad and calling back from the queue channel record. D Using call memory D Calling back from the queue channel q While in the standby condition, push and hold [P1] (Digital) for 1 sec. to enter the queue memory channel selection mode. w Push [Up] or [Down] to select the desired record.
IC-F70_F80-1.qxd 05.1.18 4:26 PM 4 Page 22 (1,1) BIIS OPERATION D Direct code entry q While in the standby condition, push [P3] (TX Code Enter) to enter the TX code edit mode. u Push [PTT] to transmit; release to receive. i Push [P4] (Moni(Audi)) to send the ‘Clear down’ signal. • Code digit for editing blinks. For your information When the “UpDate” setting for the call code is enabled, the set code is overwritten into the call code memory.
IC-F70_F80-1.qxd 05.1.18 4:26 PM Page 23 (1,1) BIIS OPERATION 4 ■ Receiving a message D Receiving a status message D Receiving an SDM (Short Data Message) q When a status message is received; q When an SDM is received; • Beeps sound. • The calling station ID (or text) and the status message is displayed alternately when the indication mode is 1 line, depending on the setting. X w Push [P4] (Moni(Audi)) to return to the standby condition.
IC-F70_F80-1.qxd 05.1.18 4:26 PM 4 Page 24 (1,1) BIIS OPERATION D Received message selection The transceiver memorizes the received message in the memory. Up to 6 messages for status and SDM, or 95 character SDM’s can be memorized. The oldest message is erased when the 7th message is received. However, once the transceiver is powered OFF, all messages are cleared. q Push and hold [P1] (Digital) for 1 sec.
IC-F70_F80-1.qxd 05.1.18 4:26 PM Page 25 (1,1) BIIS OPERATION 4 ■ Transmitting a status D General D Transmitting a status The status message can be selected with the programmed text, and the message text is also displayed on the function display of the called station. Up to 24 status types (1 to 24) are available, and the status messages 22 and 24 have designated meanings.
IC-F70_F80-1.qxd 05.1.18 4:26 PM 4 Page 26 (1,1) BIIS OPERATION ■ Transmitting an SDM (Short Data Message) D Programming an SDM memory D General The short data message, SDM, can be sent to an individual station or group stations. Also, 8 SDM memory channels are available and the messages can be edited via PC programming. D Transmitting an SDM q While in the standby condition, push [P1] (Digital), then push [Up] or [Down] or rotate [DIAL] to select the desired station/group code.
IC-F70_F80-1.qxd 05.1.18 4:26 PM Page 27 (1,1) BIIS OPERATION 4 ■ Position data transmission • Available characters Key Characters [0] [1] [2] [3] [4] [5] [6] [7] [8] [9] NOTE: A decimal point can only be written with the CSF70/F1700 CLONING SOFTWARE. Pre-programmed characters can be rewritten with the 10-keypad, except for the decimal point, as it is not included in the transceiver character list, and cannot be displayed again.
IC-F70_F80-1.qxd 05.1.18 4:26 PM 4 Page 28 (1,1) BIIS OPERATION ■ Printer connection ■ Auto emergency transmission When the optional cable is connected to the transceiver, a printer can be connected to print out the received SDM content and the ID of the station who sent the message. Ask your dealer or system operator for connection details. When [Emergency Single (Silent)] or [Emergency Repeat (Silent)] is pushed, an emergency signal is automatically transmitted for the specified time period.
IC-F70_F80-1.qxd 05.1.18 4:26 PM Page 29 (1,1) BIIS OPERATION 4 ■ BIIS indication The following indications are available for the BIIS operation on a BIIS channel. CONNECT : Individual/group call is successful. OK : Message (status or SDM) transmission is successful. FAILED : No answer back is received. WAIT : Appears during retry of the call (2nd call). CLR DOWN : End the communication. BUSY : Operating channel is in the busy condition.
IC-F70_F80-1.qxd 05.1.18 4:26 PM 5 Page 30 (1,1) BATTERY CHARGING ■ Battery charging ■ Battery caution Prior to using the transceiver for the first time, the battery pack must be fully charged for optimum life and operation. R DANGER Charge the specified Icom batteries only. CAUTION: To avoid damage to the transceiver, turn the power OFF while charging. • Recommended temperature range for charging: +10°C to +40°C (+50°F to +104°F) • Use the specified chargers (BC-119N and BC-121N).
IC-F70_F80-1.qxd 05.1.18 4:26 PM Page 31 (1,1) BATTERY CHARGING 5 ■ Optional battery chargers ï AD-110 installation ï Rapid charging with the BC-119N+AD-110 q Install the AD-110 desktop charger adapter into the holder space of the BC-119N/BC-121N. w Connect the plugs of the BC-119N/BC-121N to the AD-110 desktop charger adapter with the connector, then install the adapter into the charger with the supplied screws. The optional BC-119N provides rapid charging of battery packs.
IC-F70_F80-1.qxd 05.1.18 4:26 PM 5 Page 32 (1,1) BATTERY CHARGING ï Rapid charging with the BC-121N+AD-110 The optional BC-121N allows up to 6 battery packs to be charged simultaneously. The following items are additionally required. • Six AD-110 charger adapters • An AC adapter (BC-124) or the DC power cable (OPC-656) q Insert the battery pack with/without the transceiver into the charger.
IC-F70_F80-1.qxd 05.1.18 4:26 PM Page 33 (1,1) BATTERY CASE 6 ■ Optional battery case (BP-237) When using the optional battery case attached to the transceiver, install 6 × AA (LR6) size alkaline batteries as illustrated at right. q Hook your finger under the latch, and open the cover in the direction of the arrow (q). (Fig.1) w Then, install 6 × AA (LR6) size alkaline batteries. (Fig.2) • Install the alkaline batteries only. • Be sure to observe the correct polarity.
IC-F70_F80-1.qxd 05.1.18 4:26 PM 7 Page 34 (1,1) SWIVEL BELT CLIP ■ MB-93 contents Qty. q Belt clip ……………………………………………………… 1 w Base clip …………………………………………………… 1 q w ■ To attach q Release the battery pack if it is attached. (p. 2) w Slide the base clip in the direction of the arrow until the base clip is locked and makes a ‘click’ sound. 34 e Clip the belt clip to a part of your belt. And insert the transceiver into the belt clip until the base clip inserted fully into the groove.
IC-F70_F80-1.qxd 05.1.18 4:26 PM Page 35 (1,1) SWIVEL BELT CLIP 7 ■ To detach q Turn the transceiver upside down in the direction of the arrow and pull out from the belt clip. w Release the battery pack if it is attached. (p. 2) e Pinch the clip (q), and slide the base clip in the direction of the arrow (w). q w 7 CAUTION! HOLD THE TRANSCEIVER TIGHTLY, WHEN HANGING OR DETACHING THE TRANSCEIVER FROM THE BELT CLIP.
IC-F70_F80-1.qxd 05.1.18 4:26 PM 8 Page 36 (1,1) SPEAKER-MICROPHONE ■ Optional HM-138 description Alligator type clip To attach the speaker-mic. to your shirt or collar, etc. ■ Attachment Attach the connector of the speaker-microphone into the [SP/MIC] connector on the transceiver and tighten the screw. PTT switch Transmits while pushed Receives while released Microphone Speaker NEVER immerse the connector in water.
IC-F70_F80-1.qxd 05.1.18 4:26 PM Page 37 (1,1) OPTIONS 9 D BATTERY PACK D BELT CLIPS • BP-235 Li-Ion BATTERY PACK 7.4 V/1600 mAh Li-Ion battery pack, allows more than 8 hours operation. The same as supplied with the transceiver. The BP-235 meets IPX waterproof specification grade 7. • BP-236 Li-Ion BATTERY PACK 7.4 V/2400 mAh Li-Ion battery pack, allows more than 12 hours operation. The BP-236 meets IPX waterproof specification grade 7.
IC-F70_F80-1.qxd 05.1.18 4:26 PM 9 Page 38 (1,1) OPTIONS D OTHER OPTIONS ï About VS-1SC VOX/PTT CASE • HM-138 SPEAKER-MICROPHONE Full-sized waterproof (IPX grade 7; 1m/30 min.) speakermicrophone including alligator type clip to attach to your shirt or collar, etc. • HS-94/HS-95/HS-97 HEADSET + VS-1SC VOX/PTT CASE HS-94: Ear-hook type HS-95: Neck-arm type HS-97: Throat microphone VS-1SC: VOX/PTT switch box for hands-free operation, etc.
IC-F70_F80-1.qxd 05.1.18 4:26 PM Page 39 (1,1) OPTIONS VOX gain and delay adjustment q Attach the connector of the VS-1SC into the [SP/MIC] connector on the transceiver and tighten the screw. 9 • VOX Delay The VOX delay time can be set from 0.5 to 3.0 sec. (0.5 sec. step) for a convenient interval before returning to receive. • Toggle the toggle switch to [VOX]. w Enter user set mode. (p. 17) e Push [P0] several times to select the “VOX Gain” or “VOX Delay” items.
IC-F70_F80-1.qxd 05.1.18 4:26 PM 10 Page 40 (1,1) SAFETY TRAINING INFORMATION Your Icom radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as “Occupational Use Only”, meaning it must be used only during W ARN ING the course of employment by individuals aware of the hazards, and the ways to minimize such hazards. This radio is NOT intended for use by the “General Population” in an uncontrolled environment.
IC-F70_F80-1.qxd 05.1.18 4:26 PM Page 41 (1,1) SAFETY TRAINING INFORMATION 10 Electromagnetic Interference/Compatibility During transmissions, your Icom radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals, aircraft, and blasting sites.
IC-F70_F80-1.qxd 05.1.
IC-F70_F80-1.qxd 05.1.
IC-F70_F80-1.qxd 05.1.18 4:31 PM A-6418D-1US-q Printed in Japan © 2004–2005 Icom Inc.