IMPORTANT EXPLICIT DEFINITIONS READ THIS INSTRUCTION MANUAL CAREFULLY before attempting o operate 'the transceiver. SAVE THIS INSTRUCTION MANUAL — This instruction: manual: contain important safety and operating instructions for the 1C-M719. The DSC function is: not standard Tor any of the 1C-M710 versions and is possible with the IC-M710 MDSE versions only. To use the DSC function, an optional GM:110DSC DSC TERMINAL UNIT must: be connected to the IC-M710 MDSE.
IN CASE OF EMERGENCY (for maritime operation) It your vessel regulates assistance; contact other vessels and the Coast Guard by sending a' distress cation 2182 kHz: Or, transmit your distress ‘call using digital selective calling on 2187 kHz > USING 2182 kHz WITH VOICE (3} Push: [2182kHz] to select the emergency frequency. @ Push [ALARM] and {TX FREQ] for 1 sec. 1o transmittal-tone alarm signal foray least 30 sec: transceiver. automatically stops the alarm after.
OPERATING RULES AND GUIDELINES 1 Before transmitting: monitor the channel you wish o ise! s as Yo avoid interrupting transmissions Already in progress. NN » CALL PROCEDURES Calls must-be properly identified :and: time limit: must he respected. £ 1 Give your call sign each dime you call another vessel or coast station.
2 PANEL DESCRIPTION W Front panel o6 © BITE MARINE HANOVERIAN Com =M o e MICROPHONE SPEAKER Omen: 860 MICROPHONE CONNECTOR {p. 16) Accepts: the supplied ‘microphone or an optional handset. %NOTE No audio is ‘output via: the: speaker: when % microphone or handset is ot connected. € POWER SWITCH Tunis power ON and OFF. © SPEAKER OFF SWITCH Turns the speaker ON:and OFF. L% g appears on the display wheels the speaker is trend OFF. ANy external speaker connected 1o the rear panelists not turned OFF.
@ KEYPAD aX. e Enters: the selected: channel number (or Trequency®) for direct channel selection: (p.6) *Flores a receive frequency. into a user channel or {TU simplex channel when: Pushing [ECCL T appears) = entering the desired frequency via the keypad < pushing and molding Adjusts the: HF ‘gain after pushing [FUN] 1o reduce the receiver sensitivity. (p. 8) »Flores ‘transmitter: frequency: into:a user channel (except General version) when: = pushing [TX] ¢ g7 blinks).
.| 2 PANEL DESCRIPTION M Display € ALARM INDICATOR (p. i) Appears:when: the alarm function is: activated such: for an: alarm test: or: distress: alarm: trans: mission: =:Not available on: General version: © RECEIVE INDICATOR (0.9 Appears while receiving ‘and when the squelch is pore. © TUNE INDICATOR (p. 8) Blinks while the connected antenna tuner; such as loom's Is:being tuned.
SELECTING A CHANNEL 3 M Selecting a channel The ‘transceiver has 180 ‘user channels and 1TU ‘channels. However, the number of user:channels ‘can be optionally restricted and ITU channels are not NOTE: When Channel 0 candor 2182 kHz is section is: NOT ‘possible, © In ‘such ‘a ‘case; push % % ejected: with the [2182KHz] switch, channel sec. available With sortie versions. [2182KHz] in advance.
| 3 SELECTING A CHANNEL < Using the keypad Direct:channel selection via the keypad is available forging rehang selection: (1) Be sure 7 does not appear on the display. =1t appears, push [CEL 10 delete |t @) Enter the desired channel number via the key: pad: A user channel s ‘selected when channel 1-160 s (it {in ax: umber may be optionally restricted).
l Selecting a frequency The transceiver has 0.5 1o 30.0 MHz general coverage receive capability with 100 Hz resolution. The receive frequency can be changed instantly, independent: dent ot the transmit frequency. SELECTING A CHANNEL 3 NOTE: The selected frequency is used for tempo: ray receiving {transmitting is not available}. This frequency is: cleared once the channels changed. I you want o program & frequency, refer to p.i 11, memory programming.
o ’ 4 RECEIVE AND TRANSMIT Il Basic voice receive and transmit 1) Be sure of the following in advance: * Microphone disconnected; * [SPEAKER] switch is turned OFF. *{SLY switch nutted OFF. » {CLARITY] control is set 1o center position; () = [SPEAKER] [saL] MICROPHONE connector [CLARITY] (23 Select the desired channel to be received wither [GROUP] and [CHANNEL] selectors.
M Functions for receive RECEIVE AND TRANSMIT 4 > Squelch function This function detects signals with voice ‘components and ‘squelches (mutes) Unwanted signals 'such as non modulated: beat signals. | This: provides: quiet stand by When linefeed 1o receive weak signals, the squelch should be turned OFF. »Push [SILT 10 turn: the squelch function ON: and OFF.
4 RECEIVE AND TRANSMIT Il CW operation ‘The ‘transceiver has the "following CW keying fea: tires ‘and they can be selected in 'set mode as described on p. 14 »Full break-In (receiving is possible white Transmitting) » Daley keying {automatic transmission with keying) = OFF (manual transmission ia necessary before keying) () Connect a CW lever or an external electronic keyed 1o the ACCRA) socket as shown at fight. @ Select the desired channel 16 operate CW.mode.
USER CHANNEL PROGRAMMING 5 B Programming a frequency The 1C-M710 has up o 160 user-programmable channels each with channel name capability .ot UPI 7 alphanumeric characters. & Receive frequency (1) Select the desired user channel fo be programmed. =Channels 1 fo 160 maximum are programmable. @) Push [CE} 1o select frequency selection mode, L% and frequency appear on tha display. @ Enter the desalted frequency via the keypad 'with 5or 6 digits: 2 Or rotate’ the [CHANNEL] “deletion W sangs the piquancy.
B 6 Set mope Il Set mode operation Set mode operation fs: used for programming: infrequently: changed values ‘or conditions ‘of functions: The IC-M710 has uproot 13 such items, Some: of the set ‘mode totems describable in ' this section are not available on some transceiver vert sins. {0 Rush [POWER] 1o trn prows OFF, I (2) While pushing and: holding [FUN] turn [Power] RUNG (1] power set mode. “ Set mode js selected and ohe of s rems appears.
CONNECTIONS AND INSTALLATION 7 M Connections on rear panel Optional © ANTENNA CONNECTOR (p.19) +:Connects band antenna with 4 50 Q matched coaxial cable sand a PL259 plug. @ GROUND TERMINAL (p. 18} IMPORTANT! Connects: a ship's (of vehicle's) ground. :Bee p. 18 for details. © ALCOA) and ACCRA) SOCKETS Seep: 16 for derails O CLONE JAG For Dealer Use only. €@ DSC or REMOTE SOCKETS * DSC socket for MDSE versions: = Consents ‘an optional GM-110DSE DSC TERMINAL UNIT for DSC operation.
7 CONNECTIONS AND INSTALLATION M Ground connection The transceiver and antenna tuner MUST have an adequate ground connection. Otherwise, the overall efficiency. of the ‘transceiver and antenna: net installation will: be: reduced i Electrolysis, electrical shocks and interference from other equipment could also occur. For best results; gse the heaviest gauge wire or strap available and make the connection as short as possible.
7 CONNECTIONS AND INSTALLATION M Mounting 7 /A WARNING: NEVER mount the trans caver overhead.: The weight of the transceiver is approximately: 8 kg, bt its apparent: weight: will 7 increase several fold due to wave ‘shocks or Libra: g son. ‘The transceiver must be mounted on a flat 7 SN hard surface. ¥ Mounting Location Select & location Wat: provides says ‘access 10 the tron panel for \navigation: safely,; ‘has good ventilation ‘and is not subjection sea spray.
CONNECTIONS AND INSTALLATION | 7 M installing options < Opening the case Follow the case: and: cover opening procedures shown here ‘when :you: want to:install an ‘option: or adjust a settling for non-committer control: () Remove 9 screws’ from the tear panel. then remove the rear frame and rear sealing: 2 Remove the transceiver's case as shown at fight. 3 When reassembling the cover, cheek thi Hollow: ing points: s Inter rial fan: and slits in the case are on the same side.
