N2QF User manual 1
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. “To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations.
CONTENTS Product introduction 1. Product interface introduction 2. Product function brief ※AP Bridge Mode ※Client Bridge Mode ※WDS Mode How to Apply N2QF 3. How to Install N2QF F Device 4. How to Configure N2QF 4-1. How to Setup your PC 4-2. N2QF 's Function Settings ※AP Bridge Mode Setting ※Client Bridge Mode Setting ※WDS Mode Setting Product introduction 1.
Dashboard: Show the current status information about the N2QF . Wizard: Configure your N2QF F quickly and work it. Network: Configure Local Network IP, Subnet Mask, etc., and enable DHCP Server. Wireless: Setup Wireless Settings on your N2QF . System: Important settings for related information with hardware. 2.
※AP Bridge Mode: The AP Mode is the most commonly and widely used mode of operation. Let mobile devices such as smart phones, tablets, etc. access Internet. ※Client Bridge Mode: In Client Mode, the N2QF F is receive other wireless signals; the unlimited device only be used by connecting to the N2QF . ※WDS Mode: Provides service operate in one of three modes; WDS AP Mode, WDS Client Mode, or WDS Repeater Mode. Please refer to the detailed instructions in section 4-2.
3) WDS Repeater Mode: WDS repeater, in which WDS Aps communicate with each other and with WDS Client. And extend the original wireless signal. How to Apply N2QF 3. How to Install N2QF Device 1) Connect the PC in PoE LAN port or normal LAN port of N2QF . 2) Connect the power to N2QF .
4. How to Configure N2QF 4-1. How to Setup your PC Follow the steps below to configure in Windows OS. 1) Press on the Windows Key and X on your Keyboard. 2) On the menu that appears and click Network Connections.
first and follow up the step) 4) Click Internet Protocol Version 4 (TCP/IP) then click Properties 9
5) Set your PC’s IP address manually to 192.168.1.2. And set Subnet mask to 255.255.255.0( or other address in the same subnet).
6) Click OK to save and apply your settings.
Now, you can run the Ping command in the command prompt. 7) Click on Search Icon; Typing cmd and click on the Command Prompt Icon. 8) On the Command Prompt screen; Typing “ping 192.168.1.
If the result is similar to the one shown below, it means the connection success. If the result is not similar to the one shown below, back to set PC’s address steps. 9) After connect success, open a web-browser and type in the default address http://192.168.1.1 in the address of the browser. 10) A login window will display, and enter the default password "admin" to login.
4-2. N2QF 's Function Settings Please follow the teaching steps to configure. 1) Open Wizard Settings by clicking on Wizard on the left control menu.
Country Code: Please select your country code to ensure that the radio operates according to local regulations. Operation Mode: Select the mode of operation you need to apply. 2) If you complete the configuration, please press "Next" to the next teaching step. The teaching steps here only teach you the configuration method.
know more about the operation mode, please go back to Chapter 2 Product function brief. ※AP Bridge Mode Setting 1) Radio: The default Radios is on. You can enable the radio according to your needs. 2) AP SSID: The default AP SSID of 2.4GHz Radio is “N2Q”, You can be modified and the SSID length is up to 32 characters.
3) Security settings: It allows you to use encryption provide association authentication to secure your data, and you can select different security policy. ※Client Bridge Mode Setting When you select this mode of operation, you may need to wait until the wireless scan is complete. When the wireless scan is complete, the available wireless radios and associated status will be displayed.
1) Search: Typing keywords to filter wireless radio. 2) Join Network: Click to join the wireless radio of your choice. 3) Repeat scan: Rescan for available wireless radios. When you click on the wireless radio you have joined, "Add Wireless Profile" will pop up.
If the security of the wireless radio you joined is "None", it will pop up as shown below. If you have confirmed the wireless radio you are joining, press "Apply" to save the settings.
※WDS Mode Setting If you selected WDS mode, please select the function mode you need first, and follow the teaching steps to complete the configuration. 1) WDS AP Mode: This configuration is similar to "※AP Bridge Mode Setting". Please refer to the "※AP Bridge Mode Setting" method for configuration. 2) WDS Client Mode: This configuration is similar to "※Client Bridge Mode Setting". Please refer to the "※ Client Bridge Mode Setting" method for configuration.
