This manual contains important safety precautions and information for correct usage. Please be sure to read this manual carefully before use to avoid any damage to the device. Do not place the product in hot, wet or dusty environments. Do not place the product for outdoor usage. Avoid dropping or smashing the product. Select a suitable product with correspondent maximum load of current upto 15A. Notes: This device is not waterproof. All images in this manual are for reference only.
1. Location of Controls 1. IR LED 2. System LED (Blue) 3. MIC 4. PIR (Passive infrared sensor) 5. POWER LED (Red) 6. MICRO USB (For Power Supply) 7. MICRO SD Card Slot 8. Reset (After 15 seconds to return to default setting including password) 9. Antenna 2.GETTING STARTED Congratulations on buying a iCraig Camera. This device will enable you to easily check your loved ones by viewing them while you are away. 1.
An Android™ Smart Phone or Tablet ( Android Version 4.0 or later) or an iPhone, iPad, or iPod touch (iOS Version 6.1 or later). Make sure your Smart phone or tablet, the wifi status is ON. 2.Plug the iCraig Cam into a power outlet. Insert the micro USB cable ( included) to the Micro USB jack on the device. Plug the full size USB jack of connection cable to supplied AC/DC USB Adaptor to wall outlet having AC 100240V~, 50/60 Hz. Using the supplied AC/USB Adaptor for Power Supply.
After installing your app, open the APP, press and to choose “Add new online Camera”icon to activate the APP. 4.Check your iCraig cam LED lights which indicate the status as below: Blue LED Light “Slow Blue LED light “Fast Blue LED light Flash” ==== Ready for new connection mode. Flash”=== In progress for connection “Solid blue live”=== connected. 3.
Connect to your Camera with the Phone or tablet Tap on the Camera wifi name appear on your phone to connect the device. After a success connection, your phone will show the camera WIFI name on your screen as connected wifi.
4. Method 1 – connection without QR Scan (Make sure IP camera Access Point is Connected with Smartphone) Open the APP Choose “+” on the top right screen, then Tap on “Add new online Device”. Tap on “Search(LAN)” , all connected camera will display on your screen. Tap on camera you want to connect and press “OK” to connect. Wait until the new camera Logging in successfully, you will see the camera online status appear on your screen. Now app connected with IP camera through AP (Access Point) mode.
Connect IP Camera to WIFI network Tap the Setting icon” “advance Config”. ” on Live Cam page (see as below) and choose the Tap the “WIFI Config” and choose your wifi network by identifying your network name. Input your wifi network password if needed.
Tap “OK”, it will display confirmation message if all required wifi name/password is correct. Then touch “OK”, the camera will start to reboot. Once complete, it shows “Device reboot” The new camera will logging in to your home network automatically, wait until the camera appears “online, X User” (blue word) successfully. Now it is finish setup.
5. Method 2 - connection by UID (QR Code) Scan (Make sure IP camera Access Point is Connected with Smartphone) This is another method to connect IP camera by QR code scan, procedure as below: Open the APP Choose “+” on the top right screen, then Tap on “Setup Device WIFI connection”.
” Locate your QR Code label on the back of wifi camera which is similar to this “ use your Smart Phone to aim on the QR code after pressing the QR SCAN icon on the APP screen. Choose your wifi network by identifying your network name Input your wifi network password if needed. Press “Start Configuring Wifi” icon to start connection.
Wait until the “Add New Device” icon display on app screen, and then touch it. You can see new connected device shows on “Search Device” page (see below) Tap the new device then Press “OK”, the new camera will logging in, wait until the camera appear “online, X User” (blue word) successfully. Now it is finish setup.
6. Reset (Reset button on rear of camera) If you want to connect IP camera with other network or camera works abnormally. You can press and hold “reset button” locate at rear of camera 15 seconds to reset it as manufacturer stage (erase all network data and P2P password will set to manufacturer default (8888). Use small metal pin to press and hold reset button 15 secs to reset as manufacturer default. 7.
High The current frame image quality is high Normal The current frame image quality is normal. Low Bandwidth The quality of the low bandwidth when the current frame image Adjust the brightness Adjust the contrast Open and Close MIC No function Smartphone Screenshot Smartphone Record NO FUNCTION NO FUNCTION The current frame mirror left and right The current picture mirror up and down 8.
Tap on Advance Configs Set Up: Alarm Config Select motion detection sensitivity by pressing on the icon and sensitivity screen will pop up for you to choose. Choose disable if you do not wish to have this alert. - To set up motion detection by enabling PIR sensor by sliding the icon to the right hand side.
To record on your micro SD card (Micro SD is not included) 1. Insert the Micro SD card and format. 2. Choose Record Resolution before using this feature 3. Choose File Length to set your recording time 4. Tap “OK” to enable recording Change P2P password: - Default password: 8888 and you may change the password with 4 to 10 digits. **If you have forgotten the password, press the RESET button on the back of the device for about 15s.
Time Setting: To sync with the smart phone and the app on real time by pressing “Device Time Sync with App”.
Camera reboot: Enable remotely restart the camera. If camera works abnormally, you can do this step to reboot/restart camera.
9.Mounting Your Camera (optional) Attach screws to wall and hang plate onto screws (Screws and hang plate not included) 10.Troubleshooting Cannot power on the Device Check your power source. T Cannot go online Check if your WI-FI setting is correct, proper password may be needed. Check if your router is working properly. Check your signal, your device may not be to connect due to weak WI-FI signal.
11. Specification PRODUCT SPECIFICATIONS Hardware Features and Specifications Still Image Capture Video Features Support VGA and 0.3MP resolution JPEG still capture Adjust image size and quality Flip and mirror image Audio In Audio Compression Built-in microphone, ADPCM Camera Image Sensor Lens View Angle VGA 1/4 inch CMOS sensor Focal length: 2.5mm 130° IR LEDs 10 IR LEDs, IR Mode Always on Always off Auto mode ● IR turns on when luminance. decreases to about 3 lux ● IR turns off when luminance.