Quick Start Guide

ManualsBrandsICRealtime ManualsHD Recorders16 Channel 4K AVS, Analog & IP Mini 1U Standalone DVR, No HDD

Quick Start Guide V1.02

HD Analog Video

Recorder 1U/ Mini 1U

Getting Started

A. Inspecting the Components

B. Rear Panel Identiﬁcation

Device Setup

A. Booting Up

B. Device Initialization

C. Startup Wizard

Web Operation

A. Accessing Web Interface

Remote Access

A. P2P setup to Phone App

Appendices

A. FAQ

B. Toxic or Hazardous materials or

Elements

C. Cybersecurity Recommendations

4-5

8-9

Table Of Contents

MARGIN

GUIDES

To see the guides to go:

View / Guides / Show

Guides

www.icrealtime.com

IMPORTANT SAFEGUARDS AND WARNINGS

Operating Requirement

● Install the PoE front-end device indoors.

● The Device does not support wall mount.

● Do not place and install the device in an area exposed to direct sunlight or near heat

generating devices.

● Do not install the device in a humid, dusty or fuliginous area

● Keep its horizontal installation, or install it at stable places, and prevent it from falling.

● Do not drip or splash liquids onto the device; don’t put on the device anything ﬁlled

with liquids, in order to prevent liquids from ﬂowing into the device.

● Install the device at well-ventilated places; don’t block its ventilation opening.

● Use the device only within rated input and output range

● Do not dismantle the device arbitrarily.

● Transport, use and store the device within allowed humidity and temperature range.

Electrical Safety

● Improper battery use might result in ﬁre, explosion, or inﬂammation.

● When replacing battery, make sure the same model is used.

● Use the recommended power cables in the region and conform to the rated power

speciﬁcation

● Use the power adapter provided otherwise, it may result in injury and device damage.

● The power source shall conform to the requirement of the Safety Extra Low Voltage

(SELV) standard, and supply power with rated voltage which conforms to Limited

power Source requirement according to IEC60950-1. Please note that the power

supply requirement is subject to the device label.

● Connect the device (I-type structure)to the power socket with protective earthing.

1A. Inspecting the Components

Items Detail Inspect

Package ● Appearance

● Packing Materials

● Accessories

● Any obvious damage on box

● Broken or distorted positions due to physical abuse

● The accessory box should have all materials (ie: extra

SATA cables, Remote, Power cord)

Labels ● Labels Containing the

Serial Number are

located on Device and

in box

● The serial numbers on the Labels are in vital in

tracking the device in our database. Ensure they are

not torn or lost.

Device ● Appearance

● Data, power, and fan

cables, mainboard

● Any obvious damage

● Loose connections

Summary of content (9 pages)

PAGE 1
IMPORTANT SAFEGUARDS AND WARNINGS Operating Requirement ● Install the PoE front-end device indoors. ● The Device does not support wall mount. ● Do not place and install the device in an area exposed to direct sunlight or near heat generating devices. ● Do not install the device in a humid, dusty or fuliginous area ● Keep its horizontal installation, or install it at stable places, and prevent it from falling.
PAGE 2
1B. Rear Panel Identiﬁcation The actual appearance may differ depending on the model purchased. 1. 2. 3. 4. 5. 6. Power Input Port Power On/Off Switch BNC Ports Ethernet Port VGA Port HDMI Port 2 | www.icrealtime.com 7. 8. 9. 10. 11. 12.
PAGE 3
2A. BOOTING UP 1.1 - Prerequisites ● System is being supplied appropriate power. ● A network cable is connected to a router for local and remote access. ● A mouse and display are connected to the machine to interact with the menus. DEVICE INITIALIZATION (cont.) ● ● Draw an unlock pattern to use in place of a password. Click skip if you do not want to use an unlock pattern. 2B. DEVICE INITIALIZATION 1.1 - Region Settings ● Select region and appropriate language then click next. Figure 4.2-2 1.
PAGE 4
2C STARTUP WIZARD 1.1 - General Settings ● General settings can be left at default. ● Change Auto Logout to 0 minutes to always stay logged in. 1.2 - Timezone ● Select appropriate time zone (UTC/GMT). ● Enable Daylight Savings Time (DST) if applicable. DST settings should be set to week with a start time of Mar 2nd Sun and an end time of Nov 1st Sun. 4 | www.icrealtime.com STARTUP WIZARD (cont.) 1.3 - Network ● Leave machine on DHCP so it gets assigned an IP address from the router.
PAGE 5
STARTUP WIZARD (cont) 1.5 - Encode Settings (optional) ● Lower encode settings to optimize maximum recording time. ● Recommended values are: H.265, 15FPS, VBR, 6(Best). 1.6 - Basic (optional) ● Basic settings can be left on default. ● Auto delete old ﬁles only applies to system logs. 5 | www.icrealtime.com STARTUP WIZARD (cont) 1.
PAGE 6
4A. P2P setup to Phone App: ● ● ● Log in to the local or web interface and select Main Menu> NETWORK>P2P. Enable the P2P checkbox. The Status should be: Online or Connect Success. Open the phone app (ICRSS Pro or IC VIew) Go to the Home Page and tap on Devices. 6 | www.icrealtime.com ● Tap on the “+” icon on the upper right then tap on P2P. The app will use your phone camera to scan for the QR code or you can input the Serial Number manually. ● ● Select the Device type.
PAGE 7
5A. FAQ P2P says Oﬄine even though I followed the steps in the guide 5B. APPENDIX: TOXIC OR HAZARDOUS MATERIALS OR ELEMENTS The machine may not have pulled an IP address from the router. Verify all cables are secure and there is link light activity on the Ethernet Port. You can also change the DNS servers to DHCP instead of the default 8.8.8.8 I want to access my recorder from my phone You can download our free or premium version of the app from the Play Store or the App Store.
PAGE 8
5C. Appendix: Cybersecurity Recommendations Cybersecurity is more than just a buzzword: it’s something that pertains to every device that is connected to the internet. IP video surveillance is not immune to cyber risks, but taking basic steps toward protecting and strengthening networks and networked appliances will make them less susceptible to attacks. Below are some tips and recommendations on how to create a more secured security system.
PAGE 9
● Change Default HTTP and Other Service Ports. It is recommended to change default HTTP and other service ports into any set of numbers between 1024~65535, reducing the risk of outsiders being able to guess which ports you are using. ● Enable HTTPS. It is recommended to enable HTTPS, so that you visit Web service through a secure communication channel. ● ● ● ● Enable Whitelist.