i-501 Product Information Guide
Compatible Mobile Phones The following model types of mobile phone can be charged by the base via the USB connector: MI: 1A，1S，2A，2S, 3 Samsung: Galaxy S/Galaxy S II/Galaxy S III/Galaxy S IV Moto: MB860 Lenovo: LePhone Note: Welcome. You are using BT Handset with iPhone5 charger. Please do not charge the iPhone5 and other mobile phone at the same time. This guide contains helpful information that enables you to enjoy all of the features of your BT handset.
Introduction Thank you for purchasing the Bluetooth handset. The new product offers you a unique, wireless experience using Bluetooth wireless technology. It is a model of efficiency, offering wireless connections with iPhone5. Please read this guide before use and kindly note that the contents in this guide may be updated without notice. Technical Specifications Bluetooth Compliance Bluetooth Specifications version 3.0 Frequency Band 2.
Care and Maintenance Do not attempt to open the BT handset, only the authorized maintenance staff should perform the service. Please check with your local dealer. Do not expose the handset to liquid, moisture or humidity. It is not waterproof. Do not expose the handset to dusty and dirty environment. Do not expose the handset to fire. It may result in explosion. Do not expose or store the handset in high heat.
Contents Chapter 1: Getting Started 6 Feature List 7 Package Contents 8 Bluetooth Handset Overview 9 Connecting 10 Charging 11 Turning On or Off the Handset Symptom Solution Disable Bluetooth in the iPhone5 and then enable it again, the disconnected Bluetooth connection between the handset and the iPhone5 cannot be automatically resumed. Due to differences in each iPhone5's software, so it is normal for some iPhone5 that the Bluetooth connection cannot be automatically resumed.
Chapter 5: Additional Information Troubleshooting Symptom The handset doesn't turn on. Solution Ensure the battery is properly charged, fully drained battery may take a while to charge up. once the device crush down, press the reset button which bulid in the reset hole to restart. Contact an authorized service center. Ensure the handset and the iPhone5 is turned on. The handset is unable to use with Ensure the Bluetooth feature the iPhone5. on the iPhone5 is activated.
Chapter 1: Getting Started Flash LED Features List When a new call comes in, the LED on the keypad will flash if this feature is enabled. 1. Phonebook synchronization from the iPhone5 2. Phonebook searching 3. Voice dialing / Siri 4. Call waiting 5. Handsfree conversation 6. Music playing control 7. 3.5mm headset jack for music playing (A2DP) 8. Call logs 9. Profiles setting (Normal\Silence) 10. 5 ring tone selection 11. Ring volume setting 12. LCD backlight control (5S\15S\25S) 13.
Device Name Package Contents 1 Press Once you have unpacked your Bluetooth handset, make sure that you have all of these parts. If any component is missing or broken, please call your dealer. beneath Menu. or 2 Press beneath Select. to move to 4Setting, then press or to move to 5DeviceName, then press 3 Press beneath Select. 4 Enter the name, up to 12 characters long that you want to assign to the handset, then press beneath Select.
Bluetooth Handset Overview Avoid Loss Handset After this function is enabled, once your iPhone5 and i-501 are keep away from the Bluetooth's effective range, i-501 will ring continuous even in silence mode. 1 9 8 7 11 6 15 1. Charging LED 2. LCD screen 3. Up key 4. Music control key 5. Reject/Power key 6. Numeric keypad 7. Down key 8 1 Press 10 2 3 4 5 14 beneath Menu. or 2 Press beneath Select. to move to 4Setting, then press or to move to 3AvoidLoss, then press 3 Press beneath Select.
Charging Ring Volume BT Handset & iPhone5 1 Press The BT handset comes with a builtin rechargeable Li-Polymer battery. Before initial operation, fully charge the BT handset for 5 hours or more. or 2 Press beneath Select. To charge the Bluetooth handset or iPhone5, simply place it on the base. beneath Menu. to move to 3Profile, then press or to move to 3RingVol, then press 3 Press beneath Select. or to select the ring volume, then press 4 Press beneath Select.
Profile Battery Use and Care In Call If treated with care, a rechargeable battery has a long service life. A new battery, or one that has not been used for a long period of time, could have reduced capacity the first few times it is used. You can set your handset to ring or just be silent when a new call comes in. Also, you can switch the two modes in the standby mode by pressing and holding . 1 Press beneath Menu. or 2 Press beneath Select.
Chapter 2: Bluetooth Settings Pairing with an iPhone5 To use an iPhone5 with your Bluetooth handset, you must first pair and connect the iPhone5 with the handset. 1 Place the Bluetooth handset within 1 meter away from your iPhone5. 2 Turn on the Bluetooth feature of your iPhone5. Click Settings, Bluetooth and OFF, then the iPhone5 searches for available devices. 3 Press beneath Pair to enter the pairing mode. Dialed Calls The last 10 dialed calls are stored in the call logs. 1 Press beneath Menu.
Call Logs Connecting an iPhone5 Received or Missed Calls The Bluetooth handset will connect to the last paired iPhone5 automatically when the handset is switched off then on, and within 10 meters range. Ensure the Bluetooth feature is enabled on the iPhone5. The last 10 received (or missed) calls are stored in the call logs. 1 Press beneath Menu. 2 Press Select. to move to 2Caller, then press beneath beneath Select to access 1Received or 3 Press press to choose 2Missed, then press beneath Select.
Disconnecting an iPhone5 Review or Dial a Number in Phonebook When not using the handset with the iPhone5, they can be disconnected as follows: 1 Press beneath Menu. 2 Press beneath Select to choose 1Phonebook. Method 1: Using the Bluetooth handset 3 Press beneath Select to choose 1Search. Press beneath Disc in the standby mode. After that, Not Connected appears to the right side of i-501 on the iPhone5 screen. or to scroll to the desired 4 Repeatedly press entry.
Phonebook Chapter 3: Basic Functions Download Phonebook from the iPhone5 Making a Call The phonebook on your iPhone5 can be downloaded to your Bluetooth handset. Each downloaded phonebook entry can store up to 500 entries. You can access these phonebook entries and use them to make a call. During the phonebook reviewing, if a number is more than 12 digits, press to review the other digits.
Call Switching between the Handset and an iPhone5 During a call, you can switch between your Bluetooth handset and your iPhone5. Menu Structure 1Phonebook 1 During a call using the iPhone5, click of the iPhone5, then click switches to the BT handset. 3Clear on the display . The call on the iPhone5. 2 To switch back, click The call switches back to the iPhone5. 4Opp 2Caller 3Dialed During a call, press and hold for about 2 seconds to switch the call between the Bluetooth handset and the iPhone5.
Chapter 4: Menu Settings Ending a Call Menu Navigation To end a call, press iPhone5 to end the call. To access a menu option: or . You can also use the 1 When no iPhone5 is connected, press to enter the menu, otherwise press beneath Menu to enter. Adjusting the Volume 2 To scroll through menu options, press repeatedly. During a conversation, press to increase or press to decrease the volume. The handset volume will increase or decrease. 3 To select a menu, press moving to the desired menu.
Music Control After connecting to the iPhone5, press to play the music. During music playing, press to play previous song and press to play next song (If a song is played by iPhone5, it will also be played through i-501, but you should press to enter the playing interface.
Music Control After connecting to the iPhone5, press to play the music. During music playing, press to play previous song and press to play next song (If a song is played by iPhone5, it will also be played through i-501, but you should press to enter the playing interface.
Chapter 4: Menu Settings Ending a Call Menu Navigation To end a call, press iPhone5 to end the call. To access a menu option: or . You can also use the 1 When no iPhone5 is connected, press to enter the menu, otherwise press beneath Menu to enter. Adjusting the Volume 2 To scroll through menu options, press repeatedly. During a conversation, press to increase or press to decrease the volume. The handset volume will increase or decrease. 3 To select a menu, press moving to the desired menu.
Call Switching between the Handset and an iPhone5 During a call, you can switch between your Bluetooth handset and your iPhone5. Menu Structure 1Phonebook 1 During a call using the iPhone5, click of the iPhone5, then click switches to the BT handset. 3Clear on the display . The call on the iPhone5. 2 To switch back, click The call switches back to the iPhone5. 4Opp 2Caller 3Dialed During a call, press and hold for about 2 seconds to switch the call between the Bluetooth handset and the iPhone5.
Phonebook Chapter 3: Basic Functions Download Phonebook from the iPhone5 Making a Call The phonebook on your iPhone5 can be downloaded to your Bluetooth handset. Each downloaded phonebook entry can store up to 500 entries. You can access these phonebook entries and use them to make a call. During the phonebook reviewing, if a number is more than 12 digits, press to review the other digits.
Disconnecting an iPhone5 Review or Dial a Number in Phonebook When not using the handset with the iPhone5, they can be disconnected as follows: 1 Press beneath Menu. 2 Press beneath Select to choose 1Phonebook. Method 1: Using the Bluetooth handset 3 Press beneath Select to choose 1Search. Press beneath Disc in the standby mode. After that, Not Connected appears to the right side of i-501 on the iPhone5 screen. or to scroll to the desired 4 Repeatedly press entry.
Call Logs Connecting an iPhone5 Received or Missed Calls The Bluetooth handset will connect to the last paired iPhone5 automatically when the handset is switched off then on, and within 10 meters range. Ensure the Bluetooth feature is enabled on the iPhone5. The last 10 received (or missed) calls are stored in the call logs. 1 Press beneath Menu. 2 Press Select. to move to 2Caller, then press beneath beneath Select to access 1Received or 3 Press press to choose 2Missed, then press beneath Select.
Chapter 2: Bluetooth Settings Pairing with an iPhone5 To use an iPhone5 with your Bluetooth handset, you must first pair and connect the iPhone5 with the handset. 1 Place the Bluetooth handset within 1 meter away from your iPhone5. 2 Turn on the Bluetooth feature of your iPhone5. Click Settings, Bluetooth and OFF, then the iPhone5 searches for available devices. 3 Press beneath Pair to enter the pairing mode. Dialed Calls The last 10 dialed calls are stored in the call logs. 1 Press beneath Menu.
Profile Battery Use and Care In Call If treated with care, a rechargeable battery has a long service life. A new battery, or one that has not been used for a long period of time, could have reduced capacity the first few times it is used. You can set your handset to ring or just be silent when a new call comes in. Also, you can switch the two modes in the standby mode by pressing and holding . 1 Press beneath Menu. or 2 Press beneath Select.
Charging Ring Volume BT Handset & iPhone5 1 Press The BT handset comes with a builtin rechargeable Li-Polymer battery. Before initial operation, fully charge the BT handset for 5 hours or more. or 2 Press beneath Select. To charge the Bluetooth handset or iPhone5, simply place it on the base. beneath Menu. to move to 3Profile, then press or to move to 3RingVol, then press 3 Press beneath Select. or to select the ring volume, then press 4 Press beneath Select.
Setting Base Back Light You can adjust the backlight time of the handset keypad. Then after the setting time, when no key is pressed, the backlight of the handset keypad will be off. 1 Press to move to 4Setting, then press beneath Select to choose 1BackLight. or 4 Press then press to choose among 5s, 15s and 25s, beneath Select. Key Lock After the time you set, and no key is pressed, the keypad will be locked automatically. To unlock, press and hold .
Bluetooth Handset Overview Avoid Loss Handset After this function is enabled, once your iPhone5 and i-501 are keep away from the Bluetooth's effective range, i-501 will ring continuous even in silence mode. 1 9 8 7 11 6 15 1. Charging LED 2. LCD screen 3. Up key 4. Music control key 5. Reject/Power key 6. Numeric keypad 7. Down key 8 1 Press 10 2 3 4 5 14 beneath Menu. or 2 Press beneath Select. to move to 4Setting, then press or to move to 3AvoidLoss, then press 3 Press beneath Select.
Device Name Package Contents 1 Press Once you have unpacked your Bluetooth handset, make sure that you have all of these parts. If any component is missing or broken, please call your dealer. beneath Menu. or 2 Press beneath Select. to move to 4Setting, then press or to move to 5DeviceName, then press 3 Press beneath Select. 4 Enter the name, up to 12 characters long that you want to assign to the handset, then press beneath Select.
Chapter 1: Getting Started Flash LED Features List When a new call comes in, the LED on the keypad will flash if this feature is enabled. 1. Phonebook synchronization from the iPhone5 2. Phonebook searching 3. Voice dialing / Siri 4. Call waiting 5. Handsfree conversation 6. Music playing control 7. 3.5mm headset jack for music playing (A2DP) 8. Call logs 9. Profiles setting (Normal\Silence) 10. 5 ring tone selection 11. Ring volume setting 12. LCD backlight control (5S\15S\25S) 13.
Chapter 5: Additional Information Troubleshooting Symptom The handset doesn't turn on. Solution Ensure the battery is properly charged, fully drained battery may take a while to charge up. once the device crush down, press the reset button which bulid in the reset hole to restart. Contact an authorized service center. Ensure the handset and the iPhone5 is turned on. The handset is unable to use with Ensure the Bluetooth feature the iPhone5. on the iPhone5 is activated.
Contents Chapter 1: Getting Started 6 Feature List 7 Package Contents 8 Bluetooth Handset Overview 9 Connecting 10 Charging 11 Turning On or Off the Handset Symptom Solution Disable Bluetooth in the iPhone5 and then enable it again, the disconnected Bluetooth connection between the handset and the iPhone5 cannot be automatically resumed. Due to differences in each iPhone5's software, so it is normal for some iPhone5 that the Bluetooth connection cannot be automatically resumed.
Care and Maintenance Do not attempt to open the BT handset, only the authorized maintenance staff should perform the service. Please check with your local dealer. Do not expose the handset to liquid, moisture or humidity. It is not waterproof. Do not expose the handset to dusty and dirty environment. Do not expose the handset to fire. It may result in explosion. Do not expose or store the handset in high heat.
Introduction Thank you for purchasing the Bluetooth handset. The new product offers you a unique, wireless experience using Bluetooth wireless technology. It is a model of efficiency, offering wireless connections with iPhone5. Please read this guide before use and kindly note that the contents in this guide may be updated without notice. Technical Specifications Bluetooth Compliance Bluetooth Specifications version 3.0 Frequency Band 2.
Compatible Mobile Phones The following model types of mobile phone can be charged by the base via the USB connector: MI: 1A，1S，2A，2S, 3 Samsung: Galaxy S/Galaxy S II/Galaxy S III/Galaxy S IV Moto: MB860 Lenovo: LePhone Note: Welcome. You are using BT Handset with iPhone5 charger. Please do not charge the iPhone5 and other mobile phone at the same time. This guide contains helpful information that enables you to enjoy all of the features of your BT handset.
i-501 Product Information Guide
